Santec 4420CO User Manual
MODEL NUMBER
PLEASE READ THE INSTRUCTIONS COMPLETELY
BEFORE BEGINNING THE INSTALLATION.
11
1616
1717
1818
22
22
55
44
77
1919
1212
1313
1919
4420CO10
4420CO44
4420CO75
ESTATE SERIES COLOGNE COLLECTIONESTATE SERIES COLOGNE COLLECTION
##
11
22
33
44
55
66
77
88
99
1010
3333
1111
1212
1313
1414
22
66
88
1515
1616
1717
1818
1919
PARTPART
DESCRIPTIONDESCRIPTION
Complete Spout Assembly *Complete Spout Assembly *
Rubber WasherRubber Washer
Complete Lever HandleComplete Lever Handle
Spout Mounting HardwareSpout Mounting Hardware
Hot Cartridge OnlyHot Cartridge Only
Cold Cartridge OnlyCold Cartridge Only
Complete Hot ValveComplete Hot Valve
Complete Cold ValveComplete Cold Valve
Connecting Hose to the TeeConnecting Hose to the Tee
Connecting Hose to the SupplyConnecting Hose to the Supply
Tee ConnectorTee Connector
Lift Rod * Lift Rod *
Lift Knob* Lift Knob*
Lift Rod Extension *Lift Rod Extension *
Complete Pop-Up *Complete Pop-Up *
Aerator WasherAerator Washer
Aerator Basket with RestrictorAerator Basket with Restrictor
Aerator Housing *Aerator Housing *
Body mounting hardwareBody mounting hardware
Assembly *Assembly *
LineLine
PART #PART #
PS-2EC00-UPS-2EC00-U
PM-400PM-400
00CO00CO
P0431P0431
P0418P0418
P0419P0419
P0466P0466
P0467P0467
P0441P0441
P0440P0440
P0427P0427
P02645P02645
P0254P0254
P02646P02646
P0202P0202
PM-510PM-510
PM-320PM-320
P0944-UP0944-U
* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.
TOOLS THAT YOU MAY NEED
1010
1414
1111
1010
99
1515
INSPECTED BY
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
.
AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 ¼” AND MAXIMUM OF 1 ½”
4420CO
1. SPOUT INSTALLATION
A- Remove the tee connector (11), spout mounting hardware (4)
connector washer from the bottom of the spout assembly. Apply a
ring of silicone caulking around the center hole on the top of the sink.
(Do not use plumbers' putty which can damage the spout finish).
- From the top of the deck, insert the spout's threaded shank with the lift
rod (12) and knob (13) through the center hole of the sink.
B- Slip the spout mounting hardware (4) back onto the spout. First the
notched rubber washer, then the notched metal washer, wing nut and
the last the brass lock nut. Hand tighten the lock nut.
- Attach the lift rod extension (14) to the lift rod (12).
Make sure the lift rod operates smoothly. Adjust it if necessary.
C- Align the spout and secure the spout to the counter by tightening the
2 screws on the wing nut.
A
Lift Rod
B
Lift Knob
Lift Rod Extension
C
Lift Rod
rubber washer
Notched rubber washer
Notched metal washer
Wing Nut
Brass lock nut
Brass lock nut
- Place the tee connector washer into the tee connector (11) and
thread on the tee connector at the end of the spout shank.
Tighten to seal.
2. HANDLE TRIM INSTALLATION
HANDLE TRIMS ARE READY FOR SIMPLE DROP IN INSTALLATION.
DO NOT DISASSEMBLE.
A- Remove the valve body mounting hardware (19) from the valve body.
- Make sure the handle with the “cold” blue label is installed at the right side
of the spout (looking from the front) and the handle with the “hot” red label
at the left side of the spout.
- Apply a ring of silicone caulking around the handle hole on the sink top.
(Do not use plumbers' putty which can damage the finish of the faucet).
- Slip the valve body’s flexible hoses from the top of the sink or counter through
the appropriate hole next to the spout. Aim the tee connecting hoses (9)
toward the tee connector (11).
Tee connector & washer
A
rubber washer
SANTEC SANTEC
PAGE 02
Loading...