Santec 4220GL User Manual

MODEL NUMBER

PLEASE READ THE INSTRUCTIONS COMPLETELY
BEFORE BEGINNING THE INSTALLATION.

1616

1717

1818

22

33

1919

22

44

55

77

1313

1010

1212

1111

1919

4220GL10
4220GL41

4220GL23
4220GL75

ESTATE SERIES MONTAGE COLLECTIONESTATE SERIES MONTAGE COLLECTION

WIDESPREAD FAUCET WITH “GL” HANDLESWIDESPREAD FAUCET WITH “GL” HANDLES

##

11

22
33

44
55

66

77

33

88

99

1010

22

1111
1212

66

1313
1414

88

1313

1515
1616
1717
1818

1919

2020

PARTPART

DESCRIPTIONDESCRIPTION

Complete Spout Assembly *Complete Spout Assembly *

Flange Rubber WasherFlange Rubber Washer

Complete GL Lever HandleComplete GL Lever Handle

Spout Mounting HardwareSpout Mounting Hardware

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only

Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee

Connecting Hose to the SupplyConnecting Hose to the Supply

Tee ConnectorTee Connector

Washer for the Tee ConnectorWasher for the Tee Connector

Valve Body Mounting HardwareValve Body Mounting Hardware

Lift Knob* Lift Knob*

Complete Pop-Up *Complete Pop-Up *

Aerator WasherAerator Washer

Aerator Basket with RestrictorAerator Basket with Restrictor

Aerator Housing *Aerator Housing *

Handle Top Lock Nut Handle Top Lock Nut

Lift RodLift Rod

Assembly *Assembly *

LineLine

1414

1010

2121

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

PART #PART #

PS-2EE00SPS-2EE00S

PM-400PM-400

00GL00GL

P0431P0431

P0418P0418

P0419P0419

P0466P0466

P0467P0467

P0441P0441

P0440P0440

P0427P0427

P0205P0205

P0202P0202

PM-306PM-306

PM-305PM-305

P0948UP0948U

PM-107PM-107

P0214P0214

99

TOOLS THAT YOU MAY NEED

DIMENSIONS

2½”

4¾”

1515

3½”

33

2½”

INSPECTED BY

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

.

AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 ¼” AND MAXIMUM OF 1 ½”

4220GL

1. SPOUT INSTALLATION

A- Remove the tee connector (11), spout mounting hardware (4) and tee

connector washer (12) from the bottom of the spout assembly. Apply a
ring of silicone caulking around the center hole on the top of the sink.
(Do not use plumbers' putty which can damage the spout finish).

- From the top of the deck, insert the spout's threaded shank with the lift
rod (21) and knob (14) through the center hole of the sink.

B- Slip the spout mounting hardware (4) back onto the spout. First the

notched rubber washer, then the notched metal washer, wing nut and
the last the brass lock nut.

- Make sure the lift rod operates smoothly. Adjust it if necessary.

- Hand tighten the lock nut.

C- Align the spout and secure the spout to the counter by tightening the

2 screws on the wing nut.

A

B

C

rubber washer

Notched rubber washer

Notched metal washer

Wing lock nut

Screw lock nut

Hex lock nut

Tee connector washer

Tee connector

Brass lock nut

- Place the tee connector washer (12) into the tee connector (11) and
thread on the tee connector at the end of the spout shank.
Tighten to seal.

2. HANDLE TRIM INSTALLATION

HANDLE TRIMS ARE READY FOR SIMPLE DROP IN INSTALLATION.
DO NOT DISASSEMBLE.

A- Remove the valve body mounting hardware (13) from the valve body.

- Make sure the handle with the “cold” blue label (8) is installed at the right side
of the spout (looking from the front) and the handle with the “hot” red label (7)
at the left side of the spout.

- Apply a ring of silicone caulking around the handle hole on the sink top.

(Do not use plumbers' putty which can damage the finish of the faucet).

- Slip the valve body’s flexible hoses from the top of the sink or counter through
the appropriate hole next to the spout. Aim the tee connecting hoses (9)
toward the tee connector (11).

Tee connector & washer

A

rubber washer

SANTEC SANTEC

PAGE 02