Santec 4150BL-1 User Manual
ESTATE SERIES BRITANI COLLECTION
ROMAN TUB FILLER WITH “BL” HANDLES
MODEL NUMBER
4150BL _ _
11
33
44
55
1919
1515
1616
1717
22
66
1414
66
##
Complete Spout Assembly *
1
Spout Flange *
2
Aerator Washer
3
Roman Tub Aerator without Restrictor
4
Aerator Housing *
5
Complete BL Lever Handle
6
Handle Top Lock Nut
7
Flange Rubber Washer
8
9
Hot Cartridge
Cold Cartridge
10
Valve Body Mounting Hardware
11
Complete Hot Valve
12
13
Complete Cold Valve
Quick Connect Spout Shank & Hardware
14
Set Screw
15
Spout Plug
16
17
Allen Key for Roman Tub Spout *
Tee Connector
18
O-ring for the spout plug
19
All Thread
20
PART
DESCRIPTION
Assembly *
PART #
PS-5K00S
P0-2065
PM-356
PM-355
P0948-U
00BL
PM-107
PM-400
P0420-SH
P0420-SC
P0495
P0496
KQ-5000S
PM-039
P0-257
P0255L
P0340
PM-445
P0341
* Please specify the finish when ordering the part.
1212
77
88
1111
99
2020
2020
1010
1111
77
88
1313
1818
INSPECTED BY
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”
SPOUT INSTALLATION
DO NOT REMOVE THE SPOUT PROTECTANT HOOD PRIOR TO INSTALLATION
1
- Remove the Quick Connect Spout Shank and Mounting Hardware (14) from the box.
- Remove the mounting hardware (cramped metal washer and brass lock nut) from
the Quick Connect Shank.
- From the top of the deck, insert the quick Connect shank with the brass plate
through the assigned spout hole.
- Secure the quick connect shank by putting the washer and locknut back on the
shank.
- Tighten the lock nut firmly.
Rubber Protectant Hood
Brass plate
Metal washer
Brass lock nut
4150BL _ _
2.
- Remove the faucet from the box.
- From the top of the deck, insert the spout (1) and flange (2) onto the top of quick
connect shank.
- Align the spout and tighten the set screw (15) with the Large Allen Key (17).
- Insert the spout plug (16) into the spout back hole.
- After the valve bodies are installed, connect the spout shank (14) to one of the
outlet port of the handle valve bodies (12) and (13) **
Note: for better installation it is advisable to place silicone caulking around all holes
on the top of the deck
.
HANDLE TRIM INSTALLATION
1.
- Unscrew both pre-assembled handle trim 6) with top lock nuts(7) and rubber
washers(8) from the valve bodies (12) and (13).
- Slip the valve bodies (12) or (13) up from the bottom of the tub through the
appropriate hole next to the spout. From tub top, insert the rubber washers (8) and
screw the top lock nuts (7) and the handle trim (6) back onto the valve bodies.
- Make sure that each handle turns freely in both directions. If the handle is scraping
against the stem, lower the valve body to reduce the friction.
Large Allen Key
Metal washer
Brass lock nut
Upper Lock Nut
rubber washer
Fiber Washer
Brass lock nut
PAGE 02
Loading...