Santec 4120BL User Manual

MODEL NUMBER
PLEASE READ THE INSTRUCTIONS COMPLETELY BEFORE BEGINNING THE INSTALLATION.
1616
1717
1818
22
33
1919
2020
55
77
1313
1010
2020
44
1212
1111
11
1919
2020
4120BL10 4120BL41
4120BL23 4120BL75
ESTATE SERIES BRITANI COLLECTIONESTATE SERIES BRITANI COLLECTION
WIDESPREAD FAUCET WITH “BL” HANDLESWIDESPREAD FAUCET WITH “BL” HANDLES
66
1010
33
1313
##
11
22 33
44 55
66
77
88
99 1010 1111 1212 1313
88
1414
1515 1616 1717 1818
1919
2020
1414
2121
PARTPART
DESCRIPTIONDESCRIPTION
Complete Spout Assembly *Complete Spout Assembly *
Spout Flange*Spout Flange*
Complete BL Lever HandleComplete BL Lever Handle
Spout Mounting HardwareSpout Mounting Hardware
Hot Cartridge OnlyHot Cartridge Only
Cold Cartridge OnlyCold Cartridge Only
Complete Hot ValveComplete Hot Valve
Complete Cold ValveComplete Cold Valve
Connecting Hose to the TeeConnecting Hose to the Tee
Connecting Hose to the SupplyConnecting Hose to the Supply
Tee ConnectorTee Connector
Washer for the Tee ConnectorWasher for the Tee Connector
Valve Body Mounting HardwareValve Body Mounting Hardware
Lift Knob* Lift Knob*
Complete Pop-Up *Complete Pop-Up *
Aerator WasherAerator Washer
Aerator Basket with RestrictorAerator Basket with Restrictor
Aerator Housing *Aerator Housing *
Handle Top Lock Nut Handle Top Lock Nut
Flange Rubber WasherFlange Rubber Washer
Lift RodLift Rod
Assembly *Assembly *
LineLine
PS-2EW00SPS-2EW00S
00BL00BL
P0431P0431
P0418P0418
P0419P0419
P0466P0466
P0467P0467
P0441P0441
P0440P0440
P0427P0427
P0236P0236
P0202P0202
PM-306PM-306
PM-305PM-305
P0945UP0945U
PM-107PM-107
PM-400PM-400
P0214P0214
PART #PART #
* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.
TOOLS THAT YOU MAY NEED
3¾”
DIMENSIONS
3”
5”
99
4½”
2121
1515
INSPECTED BY
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
.
AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 ¼” AND MAXIMUM OF 1 ½
4120BL
1. SPOUT INSTALLATION
A- Remove the tee connector (11), spout mounting hardware (4) and tee
connector washer (12) from the bottom of the spout assembly. Apply a ring of silicone caulking around the center hole on the top of the sink. (Do not use plumbers' putty which can damage the spout finish).
- From the top of the deck, insert the spout's threaded shank with the lift rod (21) and knob (14) through the center hole of the sink.
B- Slip the spout mounting hardware (4) back onto the spout. First the
notched rubber washer, then the notched metal washer, wing nut and the last the brass lock nut.
- Make sure the lift rod operates smoothly. Adjust it if necessary.
- Hand tighten the lock nut.
C- Align the spout and secure the spout to the counter by tightening the
2 screws on the wing nut.
A
B
C
Lift Rod
rubber washer
Notched rubber washer Notched metal washer Wing Nut Brass lock nut
Brass lock nut
- Place the tee connector washer (12) into the tee connector (11) and thread on the tee connector at the end of the spout shank. Tighten to seal.
2. HANDLE TRIM INSTALLATION
HANDLE TRIMS ARE READY FOR SIMPLE DROP IN INSTALLATION. DO NOT DISASSEMBLE.
A- Remove the valve body mounting hardware (13) from the valve body.
- Make sure the handle with the “cold” blue label (8) is installed at the right side of the spout (looking from the front) and the handle with the “hot” red label (7) at the left side of the spout.
- Apply a ring of silicone caulking around the handle hole on the sink top.
(Do not use plumbers' putty which can damage the finish of the faucet).
- Slip the valve body’s flexible hoses from the top of the sink or counter through the appropriate hole next to the spout. Aim the tee connecting hoses (9) toward the tee connector (11).
Tee connector & washer
A
rubber washer
SANTEC SANTEC
PAGE 02
Loading...
+ 2 hidden pages