Santec 3555TD User Manual

ITEM NUMBER

3555TD _ _-_ _

MODENA COLLECTION
ROMAN TUB FILLER WITH HAND HELD SHOWER - “TD” HANDLES

8.5”

6½”

1616

1818

1717

2020

1919

1515

5”

11

11.2”

33

3.9”

22

22

6.5”

44

1212

1313

1414

1010

55

88

66

SANTECSANTEC

77

44

99

1111

77

##

##

Complete Spout Assembly*

1

Complete TD Right Handle Assembly*

2
3

Complete TD Left Handle Assembly*

4

Flange Washer

5

Metal Crimped Washer

6

Lock nut, Shank

7

Valve Body Mounting Hardware

8

Hot Cartridge

9

Cold Cartridge

10

Complete Hot Valve

PART

PART

DESCRIPTION

DESCRIPTION

PART #

PS-5D00-U
00YY-TD-R
00YY-TD-L
PM-400
PM-551
PM-550

P0420-SH
P0420-SC
P0495

##

Complete Cold Valve

11

Diverter Cartridge

12
13

Diverter Mounting Hardware

14

Complete Diverter Assembly

15

Flange Hardware Pack Subassembly

16

Flange Deluxe Shower Arm (Modena)*

17

Guide Tube, Hand-Held Shower*

18

Adapter, Modena Hand Held Shower*

19

Modena, Hand Held Shower Assembly

20

Shower Hose Sub Assembly

* Please specify the finish when ordering the part.

PART

PART

DESCRIPTION

DESCRIPTION

##

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PART #

P0496
P0500R

P0500
PM-Z11
P0-300M
Z-200-2
PS-700S-3
PS-700S
HS-600

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the faucet from the box.
Remove the mounting lock nut, washer and tee connector from the
threaded spout shank.

- From the top of the deck, slip the spout with the flange and flange washer through
the assigned spout hole. Secure the spout by putting the washer and mounting nut
back onto the threaded spout shank. Align the spout and tighten the lock nut firmly.

2

- Put on Aerator rubber water seal, free flow aerator on spout mouth. Screw on aerator
housing on the spout mouth.

- Connect the tee connector to the spout shank.

3555TD _ _

Note: for better installation it is advisable to place silicone caulking around all holes on
the top of the deck

HANDLE TRIM INSTALLATION

1

- For proper handle turning direction, install the handle with the “cold” blue label
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.

- Both hot and cold side handle trims are pre-assmbled for faster installation.

- Put on the rubber washer on the base. Put the flange on the rubber washer maintaining the
co axiality. Modena handle complete assembly is to be kept on the top of it.
Put on Teflon washer in the body base of the cross handle,

2

- From the beneath of the basin or counter, screw the valve body mounting
hardware back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.

- Align the lever or cross handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.

Rubber washer

3

- Loop and connect the flexible hoses to the tee connector. Tighten to avoid
leakage.

- Connect and tighten the Inlet hoses to the supply lines.

PAGE 02