Santec 3546TD User Manual

Ø 2.175"

Ø 2.425"

ITEM NUMBER

3546TD_ _

MODENA COLLECTION

KITCHEN FAUCET ASSEMBLY WITH SIDE SPRAY AND WITH “TD” HANDLES

8.5”

1010

99

5”

1

77

3.9”

66

6.5”

10.75”

14

13

88

88

11

12

2

P/N

33

SANTECSANTEC

44

1616

SANTECSANTEC

55

99

1515

ITEM

PS-KDOOXA

1

PM-551

2

PR-017

3

P0-419

4

P0-418

5

TD-R

6

TD-L

7

PM-400

8

PO-466

9

PO-467
SM00

10

HS-2SS

11

HS 600

12

Z-200-1

13

Z-200-2

14

PR-040

15

PO-5L1

16

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

COMPLETE SPOUT ASSEMBLY, ROMAN TUB FAUCET
CRIMPED METAL WASHER
METAL NUT
HOT CARTRIDGE
COLD CARTRIDGE
COMPLETE “TD” RIGHT HANDLE ASSEMBLY
COMPLETE “TD” LEFT HANDLE ASSEMBLY
RUBBER FLANGE WASHER
“HOT"-HANDLE VALVE SUB-ASSEMBLY
“COLD"-HANDLE VALVE SUB-ASSEMBLY
METAL SIDE SPRAY *
CONNECTING HOSE*
SPRAYER HOLDER MOUNTING HARDWARE
SPRAYER HOLDER FLANGE *
SPRAYER HOLDER GUIDE TUBE*
DIVERTER TEE CONNECTOR
DIVERTER

DESCRIPTION

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the faucet from the box.
Remove the mounting lock nut (3), washer (2) and tee connector (18) from the
threaded spout shank.

- From the top of the deck, slip the spout with the flange and flange washer through
the assigned spout hole. Secure the spout by putting the washer(2) and mounting nut (3)
back onto the threaded spout shank. Align the spout and tighten the lock nut firmly.

2

- Put on Aerator rubber water seal (6, free flow aerator 7) on spout mouth. Screw on aerator
housing (8) on the spout mouth.

- Connect the tee connector (18) to the spout shank.

3546TD_ _

Note: for better installation it is advisable to place silicone caulking around all holes on
the top of the deck

HANDLE TRIM INSTALLATION

1

- For proper handle turning direction, install the handle with the “cold” blue label
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.

- Both hot and cold side handle trims are pre-assmbled for faster installation.

- Put on the rubber washer on the base. Put the flange on the rubber washer maintaining the
co axiality. Modena handle complete assembly (9) is to be kept on the top of it.
Put on Teflon washer (10) in the body base of the cross handle,

2

- From the beneath of the basin or counter, screw the valve body mounting
hardware (11 & 12) back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.

- Align the lever or cross handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.

3

- Loop and connect the flexible hoses to the tee connector. Tighten to avoid
leakage.

- Connect and tighten the Inlet hoses to the supply lines.

SANTEC SANTEC

SANTEC SANTEC

INLET HOSEINLET HOSE

Rubber washer

Metal washer

Brass lock nut

PAGE 02