Santec 3543TX User Manual
ITEM NUMBER
3543TX_ _
MODENA COLLECTION
KITCHEN FAUCET ASSEMBLY WITH “TX” CROSS HANDLES
8.5”
1
3½”
33
3.9”
22
6.5”
44
44
44
##
11
1111
22
33
SANTECSANTEC
55
SANTECSANTEC
66
77
1313
1212
1313
44
55
88
66
77
88
99
1010
99
1111
1212
1313
1010
* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.
PARTPART
DESCRIPTIONDESCRIPTION
Complete Kitchen Spout Assembly *Complete Kitchen Spout Assembly *
Complete TX Handle Right Complete TX Handle Right
Complete TX Handle LeftComplete TX Handle Left
Washers for Spout & HandleWashers for Spout & Handle
Hot Cartridge OnlyHot Cartridge Only
Cold Cartridge OnlyCold Cartridge Only
Complete Hot ValveComplete Hot Valve
Complete Cold ValveComplete Cold Valve
Connecting Hose to the TeeConnecting Hose to the Tee
Connecting Hose to the SupplyConnecting Hose to the Supply
Spout Shank Mounting HardwareSpout Shank Mounting Hardware
Tee ConnectorTee Connector
Valve Body Mounting HardwareValve Body Mounting Hardware
Assembly *Assembly *
Assembly *Assembly *
FlangesFlanges
LineLine
PART #PART #
PS-KD00SPS-KD00S
00YY-TX00YY-TX
00YY-TX00YY-TX
PM-400PM-400
P0418P0418
P0419P0419
P0466P0466
P0467P0467
P0441P0441
P0440P0440
P0040P0040
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”
SPOUT INSTALLATION
1
- Remove the faucet from the box.
Remove the mounting lock nut, washer and tee connector from the
threaded spout shank.
- From the top of the deck, slip the spout with the flange and flange washer through
the assigned spout hole. Secure the spout by putting the washer and mounting nut
back onto the threaded spout shank. Align the spout and tighten the lock nut firmly.
2
- Put on Aerator rubber water seal (6, free flow aerator on spout mouth. Screw on aerator
housing on the spout mouth.
- Connect the tee connector to the spout shank.
3543TX_ _
Note: for better installation it is advisable to place silicone caulking around all holes on
the top of the deck
HANDLE TRIM INSTALLATION
1
- For proper handle turning direction, install the handle with the “cold” blue label
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.
- Both hot and cold side handle trims are pre-assmbled for faster installation.
- Put on the rubber washer on the base. Put the flange on the rubber washer maintaining the
co axiality. Modena handle complete assembly is to be kept on the top of it.
Put on Teflon washer in the body base of the cross handle,
2
- From the beneath of the basin or counter, screw the valve body mounting
hardware back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.
- Align the lever or cross handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.
3
- Loop and connect the flexible hoses to the tee connector. Tighten to avoid
leakage.
- Connect and tighten the Inlet hoses to the supply lines.
SANTEC SANTEC
SANTEC SANTEC
SANTEC SANTEC
SANTEC SANTEC
INLET HOSEINLET HOSE
INLET HOSEINLET HOSE
Rubber washer
Rubber washer
Metal washer
Metal washer
Brass lock nut
PAGE 02
Loading...