Santec 3543TD User Manual

ITEM NUMBER

3543TD_ _

MODENA COLLECTION
KITCHEN FAUCET ASSEMBLY WITH “TD” HANDLES

8.5”

3.9”

1

22

6.5”

44

##

11
22

33

44

44
55

1414

1313

1111

1212

SANTECSANTEC

66

1515

66

77

88

88

99
1010
1111
1212

1313

99

1414
1515

PARTPART

DESCRIPTIONDESCRIPTION

Complete Kitchen Spout Assembly *Complete Kitchen Spout Assembly *

Complete TD Handle Right Complete TD Handle Right
Complete TD Handle LeftComplete TD Handle Left

Washers for Spout & HandleWashers for Spout & Handle

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only
Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee
Connecting Hose to the SupplyConnecting Hose to the Supply
Crimped Metal WasherCrimped Metal Washer
Metal NutMetal Nut

Red Fiber WasherRed Fiber Washer

Tee ConnectorTee Connector

Valve Body Mounting HardwareValve Body Mounting Hardware

Assembly *Assembly *

Assembly *Assembly *

FlangesFlanges

LineLine

PART #PART #

PS-KD00SPS-KD00S

00YY-TD-R00YY-TD-R

00YY-TD-L00YY-TD-L

PM-400PM-400
P0418P0418

P0419P0419
P0466P0466

P0467P0467

P0441P0441
P0440P0440

PM-551PM-551
PR-017PR-017
PR-078PR-078

PR-040PR-040

5”

33

44

SANTECSANTEC

55

77

1515

1010

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the faucet from the box.
Remove the mounting lock nut (3), washer (2) and tee connector (4) from the
threaded spout shank.

- From the top of the deck, slip the spout with the flange and flange washer through
the assigned spout hole. Secure the spout by putting the washer(2) and mounting nut (3)
back onto the threaded spout shank. Align the spout and tighten the lock nut firmly.

2

- Put on Aerator rubber water seal (6, free flow aerator 7) on spout mouth. Screw on aerator
housing (8) on the spout mouth.

- Connect the tee connector (4) to the spout shank.

3543TD_ _

Note: for better installation it is advisable to place silicone caulking around all holes on
the top of the deck

HANDLE TRIM INSTALLATION

1

- For proper handle turning direction, install the handle with the “cold” blue label
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.

- Both hot and cold side handle trims are pre-assmbled for faster installation.

- Put on the rubber washer on the base. Put the flange on the rubber washer maintaining the
co axiality. Modena handle complete assembly (9) is to be kept on the top of it.
Put on Teflon washer (10) in the body base of the cross handle,

2

- From the beneath of the basin or counter, screw the valve body mounting
hardware (11 & 12) back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.

- Align the lever or cross handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.

3

- Loop and connect the flexible hoses to the tee connector. Tighten to avoid
leakage.

- Connect and tighten the Inlet hoses to the supply lines.

SANTEC SANTEC

SANTEC SANTEC

INLET HOSEINLET HOSE

Rubber washer

Metal washer

Brass lock nut

PAGE 02