Santec 3520TX User Manual

ITEM NUMBER

Ø

Ø

3520TX _ _-_ _

MODENA COLLECTIONMODENA COLLECTION

WIDESPREAD FAUCET WITH “TX” CROSS HANDLESWIDESPREAD FAUCET WITH “TX” CROSS HANDLES

8.828”
7”

3.9”

3.5”

2.175”

22

11.2”

33

16

1

2.425”

##

11

22
33

44

16

55

66

77

88

6.5”

22

99
1010
1111
1212
1313
1414

1515

1616

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

PARTPART

DESCRIPTIONDESCRIPTION

Complete Spout Assembly *Complete Spout Assembly *

Complete TX Cross Lever HandleComplete TX Cross Lever Handle

Washers for Spout & HandleWashers for Spout & Handle

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only

Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee

Connecting Hose to the SupplyConnecting Hose to the Supply

Tee ConnectorTee Connector

Spout Mounting HardwareSpout Mounting Hardware

Washer for the Tee ConnectorWasher for the Tee Connector

Valve Body Mounting HardwareValve Body Mounting Hardware

Complete Pop-Up Complete Pop-Up

Lift Knob and Lift RodLift Knob and Lift Rod

Aerator Housing* Aerator Housing*

FlangesFlanges

Assembly *Assembly *

LineLine

PART #PART #

PS-2D00XAPS-2D00XA

TX TX

PM-400PM-400

P0418P0418

P0419P0419

P0466P0466

P0467P0467

P0441P0441

P0440P0440

P0427P0427

P0431P0431

P0202P0202

P0940-UP0940-U

1111

1515

SANTECSANTEC

44

1212

66

1313

1010

SANTECSANTEC

55

77

1313

1414

88

99

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

.

AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM OF 1 1/2”

SPOUT INSTALLATION

1

- Remove the tee connector, spout mounting hardware and tee connector
washer from the bottom of the spout assembly. Apply a ring of silicon caulking
around the center hole on the top of the sink. Do not use plumbers' putty which
can damage the finish of the faucet.

- From the top of the deck, insert the spout's threaded shank through the center
hole of the sink. Make sure the spout flange washer is properly placed under­ neath of the flange and snugly pressed against the sink top.

2

-- Slip the spout mounting hardware back onto the spout. First the notched rubber
washer, then the notched metal washer and lastly the brass lock nut. Hand tighten
the lock nut.

- Place the pop-up lift rod with the knob through the back hole in the spout in such a way so
that tee connector and spout mounting lock nut. Hex lock nut will come after spout lock
nut is been put in the place and tightened though the two screws. Spout lock nut should be
screwed and tightened in a position so the lift rod movement must not be restricted.

- Put on the hex lock nut. Tighten it up on the threads firmly. Make sure the lift rod operates
smoothly.

- Place the tee connector washer (into the tee connector and thread the tee
connector onto the end of the spout shank. Tighten to seal.

- Align the spout and tighten the shank lock nut firmly.

3520 TX _ _

SANTEC SANTEC

HANDLE TRIM INSTALLATION

1

- For proper handle turning direction, install the handle with the “cold” blue label
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.

- Both hot and cold side handle trims are pre-assmbled for faster installation.

- Remove the valve body mounting hardware from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout. Make sure the handle flange washer is
properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses toward the tee connector.

2

- From beneath of the basin or counter, screw the valve body mounting
hardware back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.

- Align the lever or cross handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.

SANTEC SANTEC

INLET HOSEINLET HOSE

Rubber washer

Metal washer

PAGE 02