Santec 2555YC User Manual

ITEM NUMBER

2555YC _ _-_ _

LEAR CRYSTAL COLLECTION
ROMAN TUB FILLER WITH HAND HELD SHOWER - “YC” HANDLES

11

1616

2222

1515

33

44

1414

1010

1212

33

66

1111

88

1313

1717

55

##

Complete Spout Assembly *

1

Complete Crystal Lever Handle

2

Flange Washer

3

Spout Shank Mounting

4

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

9

Complete Cold Valve

10

Diverter Cartridge

11

Diverter Mounting Hardware

Complete Diverter

12

Hand Shower Mounting Hardware

13

Hand Shower Flange and

14

Guide Tube *

15

Hand Shower Unit *

16

Hand Shower Hose

17

Aerator Washer

18

Aerator Basket

19

20

Aerator Housing *

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

Hardware

Washer *

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

22

SANTECSANTEC

1818
1919

2020

33

77

99

55

PART #

PS-5A00S

00YC

PM-400

P0420-SH

P0420-SC

P0495

P0496

P0500R

P0500

PM-Z11

Z-200-1

Z-200-2

Z-200-5

HS-600/HS-700

PM-306

PM-455

P0952-U

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the faucet from the box.
Remove the mounting lock nut and washer (4) from the threaded spout shank.

- From the top of the deck, slip the spout with the flange and flange washer (3) through the
assigned spout hole. Secure the spout by putting the washer and mounting nut back onto the
threaded spout shank. Align the spout and tighten the lock nut firmly.

2

- Connect the spout shank to one of the outlet port (OUT) of the diverter valve after the diverter
valve is installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

2555YC _ _

Rubber washer

HANDLE INSTALLATION

1.

- Unscrew the pre-assembled Lear handle trim (2) from the valve body.

- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout. From tub top, screw the handle trim (2) with flange washer (3) back onto
the valve body. The washer (3) must be gently pressed against the surface. Make sure that
the handle turns freely in both directions.

2

- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection.
Align the handle lever and tighten lock nut (5) firmly. Repeat the same procedure for the
opposite side.

- Connect the water supply lines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter
is installed. **

DIVERTER INSTALLATION

1

- Unscrew the pre-assembled Lear diverter handle trim (2) from the diverter (12).

- Slip the valve body (12) up from the bottom of the tub through the appropriate hole. From tub
top, screw the handle trim (2) with the flange washer (3) back onto the diverter. The
washer (3) must be gently pressed against the surface. Make sure that the handle turns
freely in both directions.

- Align the handle lever and tighten the lock nut (11) firmly.

Metal washer
Brass lock nut

Rubber washer

Metal washer

Brass lock nut

Rubber washer

Metal washer

Brass lock nut

** The spout, handle valve bodies and diverter can be connected with flex hoses (not provide by Santec) or copper pipe soldering.
Please note that when soldering connections, do not use excessive heat. Excessive heat can damage the joints increasing
probability of leakage.

PAGE 02