Santec 2546LA User Manual
ITEM NUMBER
2546LA _ _-_ _
LEAR COLLECTION
KITCHEN FAUCET WITH SIDE SPRAY WITH “LA” HANDLES
1919
2020
2121
11
1313
22
33
33
SANTECSANTEC
44
1111
1010
SANTECSANTEC
55
66
22
1818
77
1717
1414
1212
1414
1616
1515
88
99
##
Complete Kitchen Spout Assembly *Complete Kitchen Spout Assembly *
11
22
Complete LA Lever HandleComplete LA Lever Handle
Washers for Spout & HandleWashers for Spout & Handle
33
Hot Cartridge OnlyHot Cartridge Only
44
Cold Cartridge OnlyCold Cartridge Only
55
Complete Hot ValveComplete Hot Valve
66
Complete Cold ValveComplete Cold Valve
77
Connecting Hose to the TeeConnecting Hose to the Tee
88
Connecting Hose to the SupplyConnecting Hose to the Supply
99
Spout Shank Mounting HardwareSpout Shank Mounting Hardware
1010
DiverterDiverter
1111
Diverter Tee ConnectorDiverter Tee Connector
1212
1313
Side Spray *Side Spray *
Valve Body Mounting HardwareValve Body Mounting Hardware
1414
Connecting HoseConnecting Hose
1515
Spray Holder Mounting HardwareSpray Holder Mounting Hardware
1616
Spray Holder Flange *Spray Holder Flange *
1717
Spray Holder Guide Tube*Spray Holder Guide Tube*
1818
Aerator WasherAerator Washer
1919
Aerator Basket with RestrictorAerator Basket with Restrictor
2020
Aerator Housing *Aerator Housing *
2121
* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.
KEEP THIS INSTRUCTION FOR FUTURE REFERENCE
PARTPART
DESCRIPTIONDESCRIPTION
Assembly *Assembly *
FlangesFlanges
LineLine
PART #PART #
PS-KA00SPS-KA00S
00LA00LA
PM-400PM-400
P0418P0418
P0419P0419
P0466P0466
P0467P0467
P0441P0441
P0440P0440
SC00SC00
HS-600HS-600
Z-200-1Z-200-1
Z-200-2Z-200-2
PM-306PM-306
PM-305PM-305
P0952-UP0952-U
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”
SPOUT INSTALLATION
2546LA _ _
1
- Remove the faucet from the box.
Remove the mounting lock nut and washer (10), diverter (11) and diverter tee
connector (12) from the threaded spout shank.
- From the top of the deck, slip the spout with the flange and flange washer (3) through
the assigned spout hole. Secure the spout by putting the washer and mounting nut back
onto the threaded spout shank. Align the spout and tighten the lock nut firmly.
2
- Connect the Diverter(11) and Diverter Tee-Connector (12) to the spout shank. Make
sure all the washers are inserted between the connector and the shank.
Note: for better installation it is advisable to place silicone caulking around all holes on
the top of the deck
HANDLE TRIM INSTALLATION
1
- For proper handle turning direction, install the handle with the “cold” blue label (7)
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.
- Both hot and cold side handle trims are pre-assmbled for faster installation.
- Remove the valve body mounting hardware (14) from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout. Make sure the handle flange washer (3) is
properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses (8) toward the diverter tee connector (12).
Rubber washer
Metal washer
Brass lock nut
Rubber washer
SANTEC SANTEC
2
- From the beneath of the basin or counter, screw the valve body mounting
hardware (14) back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.
- Align the handle lever or cross handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.
3
- Loop and connect the flexible hoses (8) to the diverter tee (12). Tighten to avoid
leakage.
- Connect and tighten the Inlet hoses (9) to the supply lines.
SANTEC SANTEC
INLET HOSEINLET HOSE
Rubber washer
Metal washer
Brass lock nut
PAGE 02
Loading...