Santec 2543YC User Manual

LEAR CRYSTAL COLLECTION
KITCHEN FAUCET WITH “YC” HANDLES

ITEM NUMBER

2543YC _ _-_ _

##

11

22
33

1616

44
55

1717
1818

11

66

77

88

99
1010
1111

22

22

1212
1313
1414

33

1111

1515

1616
1717

1818

SANTECSANTEC

44

1212

66

1313

1010

SANTECSANTEC

55

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

77

1313

PARTPART

DESCRIPTIONDESCRIPTION

Complete Spout Assembly *Complete Spout Assembly *

Complete Crystal Lever HandleComplete Crystal Lever Handle

Washers for Spout & HandleWashers for Spout & Handle

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only

Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee

Connecting Hose to the SupplyConnecting Hose to the Supply

Tee ConnectorTee Connector

Spout Mounting HardwareSpout Mounting Hardware

Washer for the Tee ConnectorWasher for the Tee Connector

Valve Body Mounting HardwareValve Body Mounting Hardware

Complete Pop-Up *Complete Pop-Up *

Lift Knob and Lift Rod *Lift Knob and Lift Rod *

Aerator WasherAerator Washer

Aerator Basket with RestrictorAerator Basket with Restrictor

Aerator Housing *Aerator Housing *

1515

Assembly *Assembly *

FlangesFlanges

LineLine

PART #PART #

PS-2A00SPS-2A00S

00YC00YC

PM-400PM-400

P0418P0418

P0419P0419

P0466P0466

P0467P0467

P0441P0441

P0440P0440

P0427P0427

P0431P0431

P0202P0202

PM-426PM-426

PM-425PM-425

P0947-UP0947-U

88

99

1414

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

2543YC _ _

1

- Remove the faucet from the box.
Remove the mounting lock nut and washer (10) and tee connector (11) from the
threaded spout shank.

- From the top of the deck, slip the spout with the flange and flange washer (3) through
the assigned spout hole. Secure the spout by putting the washer and mounting nut (10)
back onto the threaded spout shank. Align the spout and tighten the lock nut firmly.

2

- Connect the tee connector (11) to the spout shank. Make sure the washer is
inserted between the tee connector and the shank.

Note: for better installation it is advisable to place silicone caulking around all holes on
the top of the deck

HANDLE TRIM INSTALLATION

1

- For proper handle turning direction, install the handle with the “cold” blue label (7)
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.

- Both hot and cold side handle trims are pre-assmbled for faster installation.

- Remove the valve body mounting hardware (12) from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout. Make sure the handle flange washer (3) is
properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses (8) toward the tee connector (11).

Rubber washer

Metal washer
Brass lock nut

Rubber washer

SANTEC SANTEC

2

- From the beneath of the basin or counter, screw the valve body mounting
hardware (12) back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.

- Align the lever or cross handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.

3

- Loop and connect the flexible hoses (8) to the tee connector (11). Tighten to avoid
leakage.

- Connect and tighten the Inlet hoses (9) to the supply lines.

SANTEC SANTEC

INLET HOSEINLET HOSE

Rubber washer

Metal washer

Brass lock nut

PAGE 02