Santec 2270CN User Manual

KRISS COLLECTIONKRISS COLLECTION

BIDET FITTING WITH “CN” HANDLESBIDET FITTING WITH “CN” HANDLES

ITEM NUMBER

2270CN _ _-_ _

##

11

22

33

44

11

55

66

77

88

99

1010

22

22

1111
1212
1313
1414

33

1515

1616

PARTPART

DESCRIPTIONDESCRIPTION

Complete Vacuum Breaker Trim *Complete Vacuum Breaker Trim *

Complete CN Lever HandleComplete CN Lever Handle

Washers for Spout & HandleWashers for Spout & Handle

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only

Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee

Connecting Hose to the SupplyConnecting Hose to the Supply

Valve Body Mounting HardwareValve Body Mounting Hardware

Complete Vacuum Breaker CartridgeComplete Vacuum Breaker Cartridge

Y- Connector Y- Connector

Connecting Hose for the Aerator Connecting Hose for the Aerator

Aerator Housing, Insert, Flange & HardwareAerator Housing, Insert, Flange & Hardware

Complete Lift Knob, Rod and Hardware *Complete Lift Knob, Rod and Hardware *

Complete Pop-Up *Complete Pop-Up *

Assembly *Assembly *

FlangesFlanges

LineLine

PART #PART #

BD4200-4cap

BD4200-4cap

BD4200-1Cylinder

BD4200-1Cylinder

BD4200-3 ring

BD4200-3 ring

00CN-R - right

00CN-R - right

00CN-L - left

00CN-L - left

PM-400PM-400

P0418P0418

P0419P0419

P0466P0466

P0467P0467

P0441P0441

P0440P0440

BD4100BD4100
PM-B100KPM-B100K

PM-B100GPM-B100G

BD4600-5 housing

BD4600-5 housing

BD4600-6 Base

BD4600-6 Base

BD4600-8 knob *

BD4600-8 knob *

BD4600-7 flange *

BD4600-7 flange *

BD4600-9 Rod *

BD4600-9 Rod *

P0202P0202

1111

SANTECSANTEC

44

66

1010

1212

55

1313

SANTECSANTEC

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

77

1414

1010

88

99

1616

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

1515

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

.

AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM OF 1 1/2”

VACUUM BREAKER INSTALLATION

1

- Remove the complete vacuum breaker trim (1) from the cartridge (11).
From the underneath of the sink, insert the vacuum breaker cartridge (11) through the
center hole of the sink with the one of 2 conical black Soft Seating China Seals inserted.

- From the top of the sink, insert the second black Soft Seating China Seal, the White Nylon
Slip Washer, then the black Plastic Inverted Lock Nut onto the Cartridge (11).
Tighten it firmly.

- Screw the Trim Cylinder onto the Cartridge (11). Tighten Firmly.

- Slip the Handle onto the Cartridge stem and secure it with the brass screw.

- Clip the Handle Cap onto the Handle after the installation is complete to check for the
water flow options.

2270CN _ _

Handle Cap
Screw

Handle

Trim Cylinder

Black plastic lock nut
White Nylon Slip Washer
Black Soft Seating China Seals

HANDLE TRIM INSTALLATION

1

- For proper handle turning direction, install the handle with the “cold” blue label (7)
at the right side of the sink (looking from the front) and the handle with the “hot”
red label at the left side of the sink.

- Both hot and cold side handle trims are pre-assmbled for faster installation.

- Remove the valve body mounting hardware (10) from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the vacuum breaker. Make sure the handle flange washer (3)
is properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses (8) toward the Y- connector (12).

2

- From beneath of the basin or counter, screw the valve body mounting
hardware (10) back to the valve body. First the rubber washer, then the white
nylon washer and lastly the brass lock nut.

- Align the lever handle properly against the sink.
Tighten the lock nut until it secures the valve body firmly.

3

- Loop and connect the flexible hoses (8) to the Y-Connector (12). Tighten to avoid
leakage.

- Connect and tighten the Inlet hoses (9) to the supply lines.

Black Soft Seating China Seals

Rubber washer

SANTEC SANTEC

SANTEC SANTEC

INLET HOSEINLET HOSE

Rubber washer

Metal washer

Brass lock nut

PAGE 02