Santec 2255CN User Manual

ITEM NUMBER

2255CN _ _-_ _

KRISS COLLECTION
ROMAN TUB FILLER WITH HAND HELD SHOWER - “CN” HANDLES

1616

1515

1717

1010

1414

1313

1818

##

Complete Spout Assembly *

1

Complete CN Lever Handle

2

Roman Tub Spout Flange *

3

Quick Connect Spout Shank & Hardware

4

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8
9

Complete Cold Valve

10

Diverter Cartridge

11

Diverter Mounting Hardware

Complete Diverter

12

Hand Shower Mounting Hardware

13

Hand Shower Flange and

14

Guide Tube *

15

Hand Shower Unit *

16

Flange Washer

17

Hand Shower Hose

18

Aerator Washer

19

Roman Tub Aerator without Restrictor

20
21

Aerator Housing *

Allen Key for Roman Tub Spout

22

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

Washer *

22

1212

1111

PART #

PS-5K00S

00CN-L - left
00CN-R - right

P0206

KQ-5100S

P0420-SH

P0420-SC

P0495

P0496

P0500R

P0500

PM-Z11

Z-200-1

Z-200-2

Z-200-5

PM-400

HS-600/HS-700

PM-356

PM-355

P0255L

11

1919

2020

2121

22

22

33

1717

1717

SANTECSANTEC

66

44

77

99

88

55

55

2222

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the Quick Connect Spout Shank and Mounting Hardware from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.

- From the top of the deck, slip the quick Connect shank through the assigned spout hole.

- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.

2.

- Remove the faucet from the box.

- From the top of the deck, slip the spout (1) with the flange(3) and flange washer (17) onto the
quick connect shank top. Align the spout and tighten the set screw with the Allen Key (22)
provided.

Metal washer
Brass lock nut

Flange washer

2255CN _ _

3

- Connect the spout shank to one of the outlet port (OUT) of the diverter valve after the diverter
valve is installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.

HANDLE INSTALLATION

1.

- Unscrew the pre-assembled handle trim (2) from the valve body.

- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout. From tub top, screw the handle trim (2) with flange washer (17) back onto
the valve body. The washer (17) must be gently pressed against the surface. Make sure that
the handles turn freely in both directions.

2

- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection.
Align the handle lever and tighten lock nut (5) firmly. Repeat the same procedure for the
opposite side.

- Connect the water supply lines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter
is installed. **

Metal washer
Brass lock nut

Flange washer

Rubber washer

Metal washer

Brass lock nut

PAGE 02