Santec 2155JC User Manual

ITEM NUMBER

2155JC _ _-_ _

GRAND COLLECTION
ROMAN TUB FILLER WITH HAND HELD SHOWER - “JC” HANDLES

11

1919

2020

1616

1515

1717

1010

1414

1313

1818

##

Complete Spout Assembly *

1

Complete JC Handle

2

Roman Tub Spout Flange *

3

Quick Connect Spout Shank & Hardware

4

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

9

Complete Cold Valve

10

Diverter Cartridge

11

Diverter Mounting Hardware

Complete Diverter

12

Hand Shower Mounting Hardware

13

Hand Shower Flange and

14

Guide Tube *

15

Hand Shower Unit *

16

Flange Washer

17

Hand Shower Hose

18

Aerator Washer

19

Roman Tub Aerator without Restrictor

20
21

Aerator Housing *

Allen Key for Roman Tub Spout

22

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

Washer *

22

1212

1111

PART #

PS-5G00S

00JC

P0206

KQ-5100S

P0416-SH

P0416-SC

P0491

P0492

P0500R

P0500

PM-Z11

Z-200-1

Z-200-2

Z-200-5

PM-400

HS-600

PM-356

PM-355

P0255L

2121

22

22

33

1717

1717

66

44

77

99

88

55

55

2222

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

2155JC _ _

1

- Remove the Quick Connect Spout Shank and Mounting Hardware from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.

- From the top of the deck, slip the quick Connect shank through the assigned spout hole.

- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.

2.

- Remove the faucet from the box.

- From the top of the deck, screw the flange (3) with the flange washer (12)onto the shank
threaded plate. Slip the spout (1) onto the quick connect shank top. Align the spout and
tighten the set screw with the Allen Key (16) provided.

3

- Connect the spout shank to one of the outlet port of the handle valve bodies after the handle
trims and valve bodies are installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.

Large Allen Key

Brass plate

Metal washer
Brass lock nut

Metal washer
Brass lock nut

HANDLE INSTALLATION

1

- Disassemble the handle trim (2) from the valve body. First the handle cap, then the screw,
then handle bell and lastly the handle flange with the washer.

- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout. From tub top, screw the handle trim (2) back onto the valve body. The washer (17)
must be gently pressed against the surface and the handle bell should not scrape against the
handle flange. Make sure that the handle turns freely in both directions.

2

- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection.
tighten lock nut with the fiber washer (5) firmly. Repeat the same procedure for the opposite
side.

- Connect the water supply lines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter
is installed. **

Handle Cap
Screw

Handle Bell

Handle Flange
Flange washer

Fiber washer

Brass lock nut

PAGE 02