Santec 2055XL User Manual

ITEM NUMBER

2055XL _ _-_ _

LINCOLN COLLECTION
ROMAN TUB FILLER WITH HAND HELD SHOWER - “XL” HANDLES

11

1818
1919

2020

1414

1515

1616

1717

1313

22

33

66

1010

1212

1111

88

55

22

22

33

44

33

SANTECSANTEC

77

99

55

##

Complete Spout Assembly *

1

Complete XL Lever Handle

2

Flange Washer

3

Spout Mounting Hardware

4
5

Valve Body Mounting Hardware

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

Complete Cold Valve

9

Diverter Cartridge

10
11

Diverter Mounting Hardware

Complete Diverter

12

Hand Shower Mounting Hardware

13

Hand Shower Flange and

14

Guide Tube *

15

Hand Shower Unit *

16

Hand Shower Hose

17

Aerator Washer

18

Aerator Basket

19

20

Aerator Housing *

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

Washer *

PART #

PS-8L00XA

00XL-C cold
00XL-H hot
00XL-P diverter

PM-400

P0416-LH

P0416-LC

P0493

P0494

P0500R

P0500

PM-Z11

Z-200-1

Z-200-2

Z-200-5

HS-600/HS-700

PM-306

PM-455

P0952-U

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the faucet from the box.
Remove the mounting lock nut and washer (4) from the threaded spout shank.

- From the top of the deck, slip the spout with the flange and flange washer (3) through the
assigned spout hole. Secure the spout by putting the washer and mounting nut(4) back onto the
threaded spout shank. Align the spout and tighten the lock nut firmly.

2

- Connect the spout shank to one of the outlet port (OUT) of the diverter valve after the diverter
valve is installed. **

2055XL _ _

Rubber washer

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

HANDLE INSTALLATION

1.

- Unscrew the pre-assembled Lincoln handle trim (2) from the valve body. First the cap, then
the button, screw (with screw driver), handle, handle bell, flange and lastly the flange washer.

- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout. From tub top, screw the handle trim (2) with flange washer (3) back onto
the valve body. The washer (3) must be gently pressed against the surface. Make sure that
the handle turns freely in both directions.

2

- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection.
Align the handle and tighten lock nut (5) firmly. Repeat the same procedure for the
opposite side.

- Connect the water supply to the supply lines through the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter
is installed. **

DIVERTER INSTALLATION

1

- Unscrew the pre-assembled Lincoln diverter handle trim (2) from the diverter (12).

- Slip the valve body (12) up from the bottom of the tub through the appropriate hole. From tub
top, screw the handle trim (2) with the flange washer (3) back onto the diverter. The
washer (3) must be gently pressed against the surface. Make sure that the handle turns
freely in both directions.

- Align the handle and tighten the lock nut (11) firmly.

Metal washer
Brass lock nut

Handle Cap
Button
Screw

Handle

Handle Bell

Handle Flange

Rubber washer

Fiber washer

Brass lock nut

Handle Cap
Button

Screw

Handle

Handle Bell

Handle Flange

Rubber washer

Rubber washer

Metal washer

Brass lock nut

** The spout, handle valve bodies and diverter can be connected with flex hoses (not provide by Santec) or copper pipe soldering.
Please note that when soldering connections, do not use excessive heat. Excessive heat can damage the joints increasing
probability of leakage.

PAGE 02