Santec 2046XL User Manual
ITEM NUMBER
2046XL _ _-_ _
LINCOLN COLLECTION
KITCHEN FAUCET WITH SIDE SPRAY WITH “XL” HANDLES
1919
11
2020
2121
22
33
33
22
1010
SANTECSANTEC
44
1111
66
SANTECSANTEC
55
77
1313
1212
88
1313
1414
99
##
11
22
33
44
55
66
77
88
99
1010
1111
1212
1313
1414
1515
1616
1717
1818
1919
2020
2121
* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.
PARTPART
DESCRIPTIONDESCRIPTION
Complete Kitchen Spout Assembly *Complete Kitchen Spout Assembly *
Complete XL HandleComplete XL Handle
Washers for Spout & HandleWashers for Spout & Handle
Hot Cartridge OnlyHot Cartridge Only
Cold Cartridge OnlyCold Cartridge Only
Complete Hot ValveComplete Hot Valve
Complete Cold ValveComplete Cold Valve
Connecting Hose to the TeeConnecting Hose to the Tee
Connecting Hose to the SupplyConnecting Hose to the Supply
Spout Shank Mounting HardwareSpout Shank Mounting Hardware
DiverterDiverter
Diverter Tee ConnectorDiverter Tee Connector
Valve Body Mounting HardwareValve Body Mounting Hardware
Connecting HoseConnecting Hose
Spray Holder Mounting HardwareSpray Holder Mounting Hardware
Spray Holder Flange *Spray Holder Flange *
Spray Holder Guide Tube*Spray Holder Guide Tube*
Side Spray *Side Spray *
Aerator WasherAerator Washer
Aerator Basket with RestrictorAerator Basket with Restrictor
Aerator Housing *Aerator Housing *
KEEP THIS INSTRUCTION FOR FUTURE REFERENCE
Assembly *Assembly *
FlangesFlanges
LineLine
1818
1717
1616
1515
PART #PART #
PS-8L00XAPS-8L00XA
00XL-C cold
00XL-C cold
00XL-H hot
00XL-H hot
PM-400PM-400
P0410 P0410
P0411 P0411
P0458 P0458
P0459 P0459
P0441P0441
P0440P0440
HS-600HS-600
Z-200-1Z-200-1
Z-200-2Z-200-2
00SC00SC
PM-306PM-306
PM-305PM-305
P0952-UP0952-U
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”
SPOUT INSTALLATION
1
- Remove the faucet from the box.
Remove the mounting lock nut and washer (10), diverter (11) and diverter tee
connector (12) from the threaded spout shank.
- From the top of the deck, slip the spout with the flange and flange washer (3) through
the assigned spout hole. Secure the spout by putting the washer and mounting nut back
onto the threaded spout shank. Align the spout and tighten the lock nut firmly.
2
- Connect the Diverter(11) and Diverter Tee-Connector (12) to the spout shank. Make
sure all the washers are inserted between the connector and the shank.
2046XL _ _
Rubber washer
Note: for better installation it is advisable to place silicone caulking around all holes on
the top of the deck
HANDLE TRIM INSTALLATION
1
- For proper handle turning direction, install the handle with the “cold” blue label (7)
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.
- Both hot and cold side handle trims are pre-assmbled for faster installation.
- Remove the valve body mounting hardware (13) from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout. Make sure the handle flange washer (3) is
properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses (8) toward the diverter tee connector (12).
2
- From the beneath of the basin or counter, screw the valve body mounting
hardware (13) back to the valve body. First the fiber washer, then the brass lock nut.
- Align the handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.
Metal washer
Brass lock nut
Rubber washer
SANTEC SANTEC
3
- Loop and connect the flexible hoses (8) to the diverter tee (12). Tighten to avoid
leakage.
- Connect and tighten the Inlet hoses (9) to the supply lines.
SANTEC SANTEC
INLET HOSEINLET HOSE
Fiber washer
Brass lock nut
PAGE 02
Loading...