Santec 2043XL User Manual

LINCOLN COLLECTION
KITCHEN FAUCET WITH “XL” HANDLES

ITEM NUMBER

2043XL _ _-_ _

1313

1414

1515

##

11

22

33
44

55
66

77
88

99

11

11

1010
1111

1212

1313

1414
1515

22

22

22

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

PARTPART

DESCRIPTIONDESCRIPTION

Complete Kitchen Spout Assembly *Complete Kitchen Spout Assembly *

Complete XL HandleComplete XL Handle

Washers for Spout & HandleWashers for Spout & Handle
Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only
Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee
Connecting Hose to the SupplyConnecting Hose to the Supply
Spout Shank Mounting HardwareSpout Shank Mounting Hardware

Tee ConnectorTee Connector

Valve Body Mounting HardwareValve Body Mounting Hardware

Aerator WasherAerator Washer

Aerator Basket with RestrictorAerator Basket with Restrictor
Aerator Housing *Aerator Housing *

Assembly *Assembly *

FlangesFlanges

LineLine

PART #PART #

PS-8L00XAPS-8L00XA

00XL-C cold

00XL-C cold

00XL-H hot

00XL-H hot

PM-400PM-400

P0410 P0410

P0411 P0411
P0458 P0458

P0459 P0459

P0441P0441
P0440P0440

PM-306PM-306

PM-305PM-305

P0952-UP0952-U

33

33

1010

SANTECSANTEC

44

66

11

22

1111

SANTECSANTEC

55

77

1212

88

99

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the faucet from the box.
Remove the mounting lock nut and washer (10) and tee connector (11) from the
threaded spout shank.

- From the top of the deck, slip the spout with the flange and flange washer (3) through
the assigned spout hole. Secure the spout by putting the washer and mounting nut (10)
back onto the threaded spout shank. Align the spout and tighten the lock nut firmly.

2

- Connect the tee connector (11) to the spout shank. Make sure the washer is
inserted between the tee connector and the shank.

2043XL _ _

Rubber washer

Note: for better installation it is advisable to place silicone caulking around all holes on
the top of the deck

HANDLE TRIM INSTALLATION

1

- For proper handle turning direction, install the handle with the “cold” blue label (7)
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.

- Both hot and cold side handle trims are pre-assembled for faster installation.

- Remove the valve body mounting hardware (12) from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout. Make sure the handle flange washer (3) is
properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses (8) toward the tee connector (11).

2

- From the beneath of the basin or counter, screw the valve body mounting
hardware (12) back to the valve body. First the fiber washer, then the brass lock nut.

- Align the cross handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.

Metal washer
Brass lock nut

Rubber washer

SANTEC SANTEC

3

- Loop and connect the flexible hoses (8) to the tee connector (11). Tighten to avoid
leakage.

- Connect and tighten the Inlet hoses (9) to the supply lines.

SANTEC SANTEC

INLET HOSEINLET HOSE

Fiber washer

Brass lock nut

PAGE 02