Santec 2020JZ User Manual

LINCOLN COLLECTIONLINCOLN COLLECTION

WIDESPREAD FAUCET WITH “JZ” HANDLESWIDESPREAD FAUCET WITH “JZ” HANDLES

ITEM NUMBER

2020JZ _ _-_ _

11

22

22

1111

33

SANTECSANTEC

44

1212

33

55

66

1313

1010

88

99

1616

1717

1818

##

11

22

33

44
55
66

77
88
99

SANTECSANTEC

1010
1111

77

1212
1313

1313

1414
1515

1616
1717
1818

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

PARTPART

DESCRIPTIONDESCRIPTION

Complete Spout Assembly *Complete Spout Assembly *

Complete JZ Handle Assembly *Complete JZ Handle Assembly *

Washers for Spout & HandleWashers for Spout & Handle

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only

Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve
Connecting Hose to the TeeConnecting Hose to the Tee

Connecting Hose to the SupplyConnecting Hose to the Supply

Tee ConnectorTee Connector

Spout Mounting HardwareSpout Mounting Hardware

Washer for the Tee ConnectorWasher for the Tee Connector

Valve Body Mounting HardwareValve Body Mounting Hardware

Lift Knob and Lift Rod *Lift Knob and Lift Rod *

Complete Pop-Up *Complete Pop-Up *

Aerator WasherAerator Washer

Aerator Basket with RestrictorAerator Basket with Restrictor

Aerator Housing *Aerator Housing *

FlangesFlanges

LineLine

PART #PART #

PS-2L00XAPS-2L00XA

00JZ00JZ

PM-400PM-400

P0418 P0418

P0419P0419

P0452 P0452

P0453P0453

P0441P0441

P0440P0440

P0427P0427

P0431P0431

P0202P0202

PM-306PM-306

PM-305PM-305

P0952-UP0952-U

1414

1515

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

.

AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM OF 1 1/2”

SPOUT INSTALLATION

1

- Remove the tee connector (10), spout mounting hardware (11) and tee connector
washer (12) from the bottom of the spout assembly. Apply a ring of silicon caulking
around the center hole on the top of the sink. Do not use plumbers' putty which
can damage the finish of the faucet.

- From the top of the deck, insert the spout's threaded shank through the center
hole of the sink. Make sure the spout flange washer (3) is properly placed under­ neath of the flange and gently pressed against the sink top.

2

- Slip the spout mounting hardware (11) back onto the spout. First the notched rubber
washer, then the notched metal washer and lastly the brass lock nut. Hand tighten the
lock nut

- Place the pop-up lift rod with the knob (14) through the back hole in the spout and
rotate the notched washers until the lift rod passes through the notch.

- Tighten the lock nut. Make sure the lift rod operates smoothly. Adjust it if necessary.

- Place the tee connector washer (12) into the tee connector (10) and thread the tee
connector onto the end of the spout shank. Tighten to seal.

- Align the spout and tighten the shank lock nut (11) firmly

HANDLE TRIM INSTALLATION

2020JZ _ _

Rubber washer

Notched rubber washer
Notched metal washer
Brass lock nut

Tee connector washer

Tee connector

1

- For proper handle turning direction, install the handle with the “cold” blue label (7)
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.

- Both hot and cold side handle trims are pre-assembled for faster installation.

- Remove the valve body mounting hardware (13) from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout. Make sure the handle flange washer (3) is
properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses (8) toward the tee connector (10).

2

- From beneath of the basin or counter, screw the valve body mounting
hardware (13) back to the valve body. First the fiber washer, then the brass lock nut.

- Align the handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.

SANTEC SANTEC

SANTEC SANTEC

Rubber washer

Fiber washer

Brass lock nut

PAGE 02