Santec 1855NX User Manual

ITEM NUMBER

1855NX _ _-_ _

REVERE COLLECTION
ROMAN TUB FILLER WITH HAND HELD SHOWER - “NX” HANDLES

33

8

8

1

1

11

191

9

2020

1515

1616

22

1010

1414

1313

1717

##

Complete Spout Assembly *

1

Complete NX Cross Handle

2

Tub Spout knob *

3

Quick Connect Spout Shank & Hardware

4

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

9

Complete Cold Valve

10

Diverter Cartridge

11

Diverter Mounting Hardware

Complete Diverter

12

Hand Shower Mounting Hardware

13

Hand Shower Flange and

14

Guide Tube *

15

Hand Shower Unit *

16

Hand Shower Hose

17

Aerator Washer

18

Roman Tub Aerator without Restrictor

19

Aerator Housing *

20

Large Allen Key for Roman Tub Spout

21

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Washer *

Assembly *

PS-5R00S

00-NX-C cold/right00-NX-C cold/right
00-NX-H hot/left

P0416-LH

1212

1111

PART #

P0230

KQ-5000S

P0416-LC

P0493

P0494

P0500R

P0500

PM-Z11

Z-200-1

Z-200-2

Z-200-5

HS600

PM-356

PM-355

P0255L

22

66

88

44

77

55

22

99

55

2121

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1855NX _ _

1

- Remove the Quick Connect Spout Shank and Mounting Hardware from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.

- From the top of the deck, slip the quick Connect shank with the brass plate through the
assigned spout hole.

- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.

2.

- Remove the faucet from the box.

- From the top of the deck, slip the spout (1) onto the quick connect shank top.
Align the spout and tighten the set screw with the Large Allen Key (21) provided.

3

- Connect the spout shank to one of the outlet port (OUT) of the diverter valve after the diverter
valve is installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.

HANDLE INSTALLATION

1.

- Remove the pre-assembled trim(2) from the valve bodies. First the cap, then button, screw,
handle bell and last the top lock nut and fiber washer.

- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout.

- From tub top, insert the top mounting hardware back onto the valve. Do not tighten.
screw the handle bell of the handle trim (2) back onto the valve body. Adjust the height of the
handle bell against the top lock nut. Make sure the handle bell is flushed against the surface.
Insert the handle onto the stem and secure it with the screw. Tighten the screw firmly.
Insert the porcelain button (”COLD” on the right handle bell and “HOT” on the left handle bell.
Align the lettering and secure it using with the handle cap. Tighten it firmly.
Make sure that the handle turns freely in both directions.

Large Allen Key

Brass plate

Metal washer
Brass lock nut

Metal washer
Brass lock nut

Handle Cap
Button

Screw

Handle

Handle Bell

Brass lock nut

Fiber washer

Fiber washer

Brass lock nut

2

- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection.
Align the handle lever and tighten lock nut (5) firmly. Repeat the same procedure for the
opposite side.

- Connect the water supply lines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter
is installed. **

PAGE 02