Santec 1755WE User Manual

ITEM NUMBER
1755WE _ _-_ _
ETNA COLLECTION ROMAN TUB FILLER WITH HAND HELD SHOWER - “WE” HANDLES
11
1616
1515
33
1414
1313
1717
##
1
Complete WE Handle
2
Flange Washer
3
Quick Connect Spout Shank & Hardware
4
Valve Body Mounting Hardware
5
Hot Cartridge
6
Cold Cartridge
7
Complete Hot Valve
8
9
Complete Cold Valve
10
Diverter Cartridge
11
Diverter Mounting Hardware
Complete Diverter
12
Hand Shower Mounting Hardware
13
Hand Shower Flange and
14
Guide Tube *
15
Hand Shower Unit *
16
Hand Shower Hose
17
Allen Key for Roman Tub Spout
18
PART
DESCRIPTION
Assembly *
Washer *
1010
22
1212
1111
PART #
PS-5700S
00WE
PM-400
KQ-5000S
P0416-SH
P0416-SC
P0491
P0492
P0500R
P0500
PM-Z11
Z-200-1
Z-200-2
Z-200-5
HS-600/HS-700
22
22
33
33
66
44
77
99
88
55
55
1818
* Please specify the finish when ordering the part.
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2
SPOUT INSTALLATION
1755WE _ _
1
- Remove the Quick Connect Spout Shank and Mounting Hardware from the box. Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect Shank.
- From the top of the deck, slip the quick Connect shank with the brass plate through the assigned spout hole.
- Secure the quick connect shank by putting the washer and locknut back on the shank. Tighten the lock nut firmly.
2.
- Remove the faucet from the box.
- From the top of the deck, slip the spout (1) onto the quick connect shank top. Align the spout and tighten the set screw with the Allen Key (18) provided.
3
- Connect the spout shank to one of the outlet port (OUT) of the diverter valve after the diverter valve is installed. **
Note: for better installation it is advisable to place silicone caulking around all holes on the top of the deck
If the trim is ordered separately, please keep the shank protector on the quick connect shank at all time to avoid damages to the unit.
Large Allen Key
Brass plate
Metal washer Brass lock nut
Metal washer Brass lock nut
HANDLE INSTALLATION
1
- Disassemble the handle trim (2) from the valve body. First the handle cap, then the screw, then handle bell with the ring and lastly the handle flange with the washer.
- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next to the spout. From tub top, screw the handle trim (2) back onto the valve body. The washer (3) must be gently pressed against the surface and the handle bell should not scrape against the handle flange. Make sure that the handle turns freely in both directions.
2
- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection. tighten lock nut with the fiber washer (5) firmly. Repeat the same procedure for the opposite side.
- Connect the water supply lines to the bottom inlets of the valve bodies. **
- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter is installed. **
Handle Cap Screw
Handle Ring
Handle Bell
Handle Flange Flange washer
Fiber washer
Brass lock nut
PAGE 02
Loading...
+ 2 hidden pages