Santec 1450WG User Manual

ALPINE COLLECTION
ROMAN TUB FILLER WITH “WG” HANDLES

ITEM NUMBER

1450WG _ _-_ _

1313

88

55

66

22

1212

11

33

44

1414

1515

22

1212

77

99

55

1111

1616

1010

##

Complete Spout Assembly *

1

Complete WG Handle

2

Spout Flange *

3

Quick Connect Spout Shank & Hardware

4

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

9

Complete Cold Valve

10

Tee Connector

11

All Thread

Flange Washer

12

Aerator Washer

13

Roman Tub Aerator without Restrictor

14
15

Aerator Housing *

Allen Key for Roman Tub Spout

16

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PART #

PS-5400S

00WG

P0206

KQ-5100S

P0416-SH

P0416-SC

P0491

P0492

P0340

P0341

PM-400

PM-356

PM-355

P0255L

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the Quick Connect Spout Shank and Mounting Hardware from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.

- From the top of the deck, slip the quick Connect shank through the assigned spout hole.

- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.

2.

- Remove the faucet from the box.

- From the top of the deck, screw the flange (3) with the flange washer (12)onto the shank
threaded plate. Slip the spout (1) onto the quick connect shank top. Align the spout and
tighten the set screw with the Allen Key (16).

Allen Key

Metal washer
Brass lock nut

1450WG _ _

3

- Connect the spout shank to one of the outlet port of the handle valve bodies after the handle
trims and valve bodies are installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.

HANDLE INSTALLATION

1.

- Disassemble the handle trim (2) from the valve body. First the handle cap, then the screw,
handle ring, handle bell and lastly the handle flange with the washer.

- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout. From tub top, screw the handle trim (2) back onto the valve body. The washer (12)
must be gently pressed against the surface and the handle bel should not scrape against the
handle flange. Make sure that the handle turns freely in both directions.

2

- Position the valve body side outlet towards the tee connector (10) for easier pipe connection.
Tighten fiber washer with lock nut (5) firmly. Repeat the same procedure for the opposite side.

- Connect the water supply lines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the tee connector (10). **

Flange washer

Metal washer
Brass lock nut

Handle Cap
Screw

Handle Ring

Handle Bell

Handle Flange
Flange washer

Fiber washer

Brass lock nut

** The spout, handle valve bodies and tee connector can be connected with flex hoses (not provide by Santec) or copper pipe
soldering. Please note that when soldering connections, do not use excessive heat. Excessive heat can damage the joints
increasing possibility of leakage.

PAGE 02