Santec 1450LM User Manual

ALPINE COLLECTION
ROMAN TUB FILLER WITH “LM” HANDLES

11

ITEM NUMBER

1450LM _ _-_ _

1313

1414

1515

88

55

66

22

1212

1111

1616

1010

22

33

1212

SANTECSANTEC

44

77

99

55

##

Complete Spout Assembly *

1

Complete LM Lever Handle

2

Spout Flange *

3

Quick Connect Spout Shank & Hardware

4

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

9

Complete Cold Valve

10

Tee Connector

11

All Thread

Flange Washer

12

Aerator Washer

13

Roman Tub Aerator without Restrictor

14
15

Aerator Housing *

Allen Key for Roman Tub Spout

16

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

PART #

PS-5400S

00LM

P0206

KQ-5100S

P0420-SH

P0420-SC

P0495

P0496

P0340

P0341

PM-400

PM-356

PM-355

P0255L

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the Quick Connect Spout Shank and Mounting Hardware from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.

- From the top of the deck, slip the quick Connect shank through the assigned spout hole.

- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.

2.

- Remove the faucet from the box.

- From the top of the deck, slip the spout (1) with the flange (3) and flange washer (12) onto
the quick connect shank top. Align the spout and tighten the set screw with the Allen Key (16)
provided..

Metal washer
Brass lock nut

1450LM _ _

3

- Connect the spout shank to one of the outlet port of the handle valve bodies after the handle
trims and valve bodies are installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.

HANDLE INSTALLATION

1.

- Unscrew the pre-assembled handle trim (2) from the valve body.

- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout. From tub top, screw the handle trim (2) with flange washer (12) back onto the
valve body. The washer (12) must be gently pressed against the surface. Make sure that
the handle turns freely in both directions.

2

- Position the valve body side outlet towards the tee connector (10) for easier pipe connection.
Align the handle lever and tighten lock nut (5) firmly. Repeat the same procedure for the
opposite side.

- Connect the water supply lines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the tee connector (10). **

Flange washer

Metal washer
Brass lock nut

Flange washer

Fiber washer

Brass Lock Nut

** The spout, handle valve bodies and tee connector can be connected with flex hoses (not provide by Santec) or copper pipe
soldering. Please note that when soldering connections, do not use excessive heat. Excessive heat can damage the joints
increasing possibility of leakage.

PAGE 02