Santec 1420LM User Manual
ALPINE COLLECTIONALPINE COLLECTION
WIDESPREAD FAUCET WITH “LM” HANDLESWIDESPREAD FAUCET WITH “LM” HANDLES
ITEM NUMBER
1420LM _ _-_ _
##
11
22
33
44
1616
1717
11
1818
55
66
77
88
99
1010
22
22
1111
1212
1313
1414
33
1111
33
1515
1616
1717
SANTECSANTEC
44
1212
SANTECSANTEC
55
1818
* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.
PARTPART
DESCRIPTIONDESCRIPTION
Complete Spout Assembly *Complete Spout Assembly *
Complete LM Lever HandleComplete LM Lever Handle
Washers for Spout & HandleWashers for Spout & Handle
Hot Cartridge OnlyHot Cartridge Only
Cold Cartridge OnlyCold Cartridge Only
Complete Hot ValveComplete Hot Valve
Complete Cold ValveComplete Cold Valve
Connecting Hose to the TeeConnecting Hose to the Tee
Connecting Hose to the SupplyConnecting Hose to the Supply
Tee ConnectorTee Connector
Spout Mounting HardwareSpout Mounting Hardware
Washer for the Tee ConnectorWasher for the Tee Connector
Valve Body Mounting HardwareValve Body Mounting Hardware
Lift Knob and Lift Rod *Lift Knob and Lift Rod *
Complete Pop-Up *Complete Pop-Up *
Aerator WasherAerator Washer
Aerator Basket with RestrictorAerator Basket with Restrictor
Aerator Housing *Aerator Housing *
Assembly *Assembly *
FlangesFlanges
LineLine
PART #PART #
PS-2400SPS-2400S
00LM00LM
PM-400PM-400
P0418P0418
P0419P0419
P0452P0452
P0453P0453
P0441P0441
P0440P0440
P0427P0427
P0431P0431
P0202P0202
PM-306PM-306
PM-305PM-305
P0952-UP0952-U
66
1313
1010
77
1313
1414
88
99
1515
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
.
AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM OF 1 1/2”
SPOUT INSTALLATION
1
- Remove the tee connector (10), spout mounting hardware (11) and tee connector
washer (12) from the bottom of the spout assembly. Apply a ring of silicon caulking
around the center hole on the top of the sink. Do not use plumbers' putty which
can damage the finish of the faucet.
- From the top of the deck, insert the spout's threaded shank through the center
hole of the sink.
2
- Slip the spout mounting hardware (11) back onto the spout. First the notched rubber
washer, then the notched metal washer and lastly the brass lock nut. Hand tighten the
lock nut
- Place the pop-up lift rod with the knob (14) through the back hole in the spout and
rotate the notched washers until the lift rod passes through the notch.
- Tighten the lock nut. Make sure the lift rod operates smoothly. Adjust it if necessary.
- Place the tee connector washer (12) into the tee connector (10) and thread the tee
connector onto the end of the spout shank. Tighten to seal.
- Align the spout and tighten the shank lock nut (11) firmly
1420LM _ _
HANDLE TRIM INSTALLATION
1
- For proper handle turning direction, install the handle with the “cold” blue label (7)
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.
- Both hot and cold side handle trims are pre-assmbled for faster installation.
- Remove the valve body mounting hardware (13) from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout. Make sure the handle flange washer (3) is
properly placed underneath of the flange and gently pressed against the sink
top. Aim the tee connecting hoses (8) toward the tee connector (10).
2
- From beneath of the basin or counter, screw the valve body mounting
hardware (13) back to the valve body. First the fiber washer, then the brass
lock nut.
- Align the handle lever handle properly against the spout.
Tighten the lock nut until it secures the valve body firmly.
Notched rubber washer
Notched metal washer
Brass lock nut
Tee connector washer
Tee connector
Rubber washer
SANTEC SANTEC
SANTEC SANTEC
Fiber washer
Brass lock nut
PAGE 02
Loading...