Santec 1355CC User Manual

ITEM NUMBER

1355CC _ _-_ _

CLASSIC CRYSTAL COLLECTION
ROMAN TUB FILLER WITH HAND HELD SHOWER - “CC” HANDLES

1414

1515

1616

1717

1313

1010

11

1818

1919

2020

22

33

33

66

44

88

1212

1111

55

2121

2222

##

Complete Spout Assembly *

1

Spout Flange *

2

Complete CC Lever Handle

3

4

Quick Connect Spout Shank & Hardware

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

Complete Cold Valve

9

Diverter Cartridge

10

Diverter Mounting Hardware

11

Complete Diverter

12

Hand Shower Mounting Hardware

13

Hand Shower Flange and

14

Guide Tube *

15

Hand Shower Unit *

16

Hand Shower Hose

17

Aerator Washer

18

Roman Tub Aerator without Restrictor

19
20

Aerator Housing *

21

Large Allen Key for Roman Tub Spout
Medium Allen Key for Handle Trim

22

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

Washer *

33

77

99

55

PART #

PS-5300S

P0250

00CC

KQ-5000S

P0416-LH

P0416-LC

P0493

P0494

P0500R

P0500

PM-Z11

Z-200-1

Z-200-2

Z-200-5

HS-600/HS-700

PM-356

PM-355

P0255L

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1

- Remove the Quick Connect Spout Shank and Mounting Hardware (4) from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.

- From the top of the deck, slip the quick Connect shank with the brass plate through the
assigned spout hole.

- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.

2.

- Remove the faucet from the box.

- From the top of the deck, slip the spout with the flange (1 and 2) onto the quick connect shank.
Align the spout and tighten the set screw firmly using the large Allen key (21).

Large Allen Key

1355CC _ _

Brass plate

Metal cramped washer
Brass lock nut

3

- Connect the spout shank to one of the outlet port (OUT) of the diverter valve after the diverter
valve is installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.

HANDLE INSTALLATION

1.

- Remove the pre-assembled handle trim (3) and top lock nut and washer (5) from the valve body.
Use the medium Allen Key (22) to loosen the handle top. For proper turning direction, the cold valve (9)
should be installed on the right side and hot valve (8) on the left side looking from the front.

- Slip the valve body (8) or (9) with the lower lock nut and washer (5) up from the bottom of the tub
through the appropriate hole next to the spout. From tub top, screw the top washer and lock nut (5)
and handle trim (3) back onto the valve body. Adjust the top lock nut to make sure that the handle
trim sits flushed against the tub surface.

2

- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection.
Align the handle lever and tighten the lower lock nut (5) firmly. Make sure that the handle turns
freely in both directions. Tighten the handle top using the medium Allen key (22).
Repeat the same procedure for the opposite side.

- Connect the water supply to tines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter
is installed. **

Medium Allen Key

Metal washer
Brass lock nut

Handle Bell

Handle Flange

Top Lock Nut
Top Fiber Washer

Lower Fiber washer

Lower Brass lock nut

Handle Top

PAGE 02