Santec 1350DD User Manual

CLASSIC COLLECTION
ROMAN TUB FILLER WITH “DD” HANDLES

ITEM NUMBER

1350DD _ _-_ _

88

55

11

1313

1414

22

33

33

1212

66

77

44

99

55

1111

1515

1616

1010

##

Complete Spout Assembly *

1

Spout Flange *

2

Complete DD Lever Handle

3

Quick Connect Spout Shank & Hardware

4

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

Complete Cold Valve

9

Tee Connector

10

All Thread

11
12

Aerator Washer

Roman Tub Aerator without Restrictor

13

14

Aerator Housing *

Large Allen Key for Roman Tub Spout

15

Medium Allen Key for Handle Trim

16

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

PART #

PS-5300S

P0250

00DD-L left
00DD-R right

KQ-5000S

P0416-LH

P0416-LC

P0493

P0494

P0340

P0341

PM-356

PM-355

P0255L

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1350DD _ _

1

- Remove the Quick Connect Spout Shank and Mounting Hardware (4) from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.

- From the top of the deck, slip the quick Connect shank with the brass plate through the
assigned spout hole.

- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.

2.

- Remove the faucet from the box.

- From the top of the deck, slip the spout with the flange (1 and 2) onto the quick connect shank.

Large Allen Key

Align the spout and tighten the set screw firmly using the large Allen key (15).

3

- Connect the spout shank to one of the outlet port of the handle valve bodies after the handle
trims and valve bodies are installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck
If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.

HANDLE INSTALLATION

1.

- Remove the pre-assembled handle trim (2) and top lock nut and washer (5) from the valve body.
Use the medium Allen Key (16) to loosen the handle top. For proper turning direction, the cold valve (9)
should be installed on the right side and hot valve (8) on the left side looking from the front.

- Slip the valve body (8) or (9) with the lower lock nut and washer (5) up from the bottom of the tub
through the appropriate hole next to the spout. From tub top, screw the top washer and lock nut (5)
and handle trim (2) back onto the valve body. Adjust the lock nut to make sure that the handle trim
sits flushed against the tub surface.

Medium Allen Key

Brass plate

Metal cramped washer
Brass lock nut

Metal washer
Brass lock nut

Handle Top

Handle Bell

Handle Flange

Top Lock Nut
Top Fiber Washer

2

Lower Fiber washer

Lower Brass lock nut

- Position the valve body side outlet towards the tee connector (10) for easier pipe connection.
Align the handle lever and tighten the lower lock nut (5) firmly. Make sure that the handle turns
freely in both directions. Tighten the handle top using the medium Allen key (16).
Repeat the same procedure for the opposite side.

- Connect the water supply to tines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the tee connector (10). **

** The spout, handle valve bodies and tee connector can be connected with flex hoses (not provide by Santec) or copper pipe
soldering. Please note that when soldering connections, do not use excessive heat. Excessive heat can damage the joints
increasing possibility of leakage.

PAGE 02