Santec 1320AA User Manual

CLASSIC COLLECTIONCLASSIC COLLECTION

WIDESPREAD FAUCET WITH “AA” HANDLESWIDESPREAD FAUCET WITH “AA” HANDLES

11

ITEM NUMBER

1320AA _ _-_ _

1515

1616

1717

1010

##

11

22

33
44
55

22

22

66

77
88

33

SANTECSANTEC

1111

SANTECSANTEC

44

55

1212

99

1212

99

66

1010

1111
1212
1313

1414

77

1515
1616

88

1717

1818

PARTPART

DESCRIPTIONDESCRIPTION

Complete Spout Assembly *Complete Spout Assembly *

Complete AA Handle Assembly *Complete AA Handle Assembly *

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only

Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee

Connecting Hose to the SupplyConnecting Hose to the Supply

Tee ConnectorTee Connector

Spout Mounting HardwareSpout Mounting Hardware

Washer for the Tee ConnectorWasher for the Tee Connector

Valve Body Mounting HardwareValve Body Mounting Hardware

Lift Knob and Lift Rod *Lift Knob and Lift Rod *

Complete Pop-Up *Complete Pop-Up *

Aerator WasherAerator Washer

Aerator Basket with RestrictorAerator Basket with Restrictor
Aerator Housing *Aerator Housing *

Allen Key for Handle Set ScrewsAllen Key for Handle Set Screws

LineLine

PART #PART #

PS-2300SPS-2300S

00A-L left

00A-L left

00A-R right

00A-R right

P0410 P0410

P0411 P0411

P0458 P0458

P0459 P0459

P0441P0441

P0440P0440

P0427P0427

P0431P0431

P0202P0202

PM-306PM-306

PM-305PM-305

P0952-UP0952-U

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

1313

1818

1414

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

.

AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM OF 1 1/2”

SPOUT INSTALLATION

1

- Remove the tee connector (9), spout mounting hardware (10) and tee connector
washer (11) from the bottom of the spout assembly.
Apply a ring of silicon caulking around the center hole on the top of the sink.
Do not use plumbers' putty which can damage the finish of the faucet.

- From the top of the deck, insert the spout's threaded shank through the center
hole of the sink.

2

- Slip the spout mounting hardware (10) back onto the spout. First the notched rubber
washer and the notched metal washer then the brass lock nut. Tighten the lock
nut. Make sure the lift rod operates smoothly. Adjust it if necessary.

- Place the tee connector washer (11) into the tee connector (9) and thread the tee
connector onto the end of the spout shank. Tighten to seal.

- Align the spout and tighten the shank lock nut (10) firmly.

1320AA _ _

Notched rubber washer
Notched metal washer
Brass lock nut

Tee connector washer

Tee connector

HANDLE TRIM INSTALLATION

1

- For proper handle turning direction, install the handle with the “cold” blue label (6)
at the right side of the spout (looking from the front) and the handle with the “hot”
red label (5) at the left side of the spout.

- Both hot and cold side handle trims are pre-assembled for faster installation.

- Remove the valve body bottom mounting hardware (12) from the valve body.
Slip the valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout. Aim the tee connecting hoses (7) toward
the tee connector (9).

2

- From beneath of the basin or counter, screw the valve body bottom mounting
hardware (12) back onto the valve body. First the fiber washer, then the brass
lock nut.

- Align the handle lever properly against the spout.
Tighten the lock nut until it secures the valve body firmly.

SANTEC SANTEC

SANTEC SANTEC

Fiber washer

Brass lock nut

PAGE 02