Santec 1155CD User Manual

ITEM NUMBER

1155CD _ _-_ _

MONARCH CRYSTAL COLLECTION
ROMAN TUB FILLER WITH HAND HELD SHOWER - “CD” HANDLES

11

1818

1919

1616

22

1515

2020

1010

1414

1313

1717

##

Complete Spout Assembly *

1

Complete CD Handle

2

Roman Tub Spout Flange *

3

Quick Connect Spout Shank & Hardware

4

Valve Body Mounting Hardware

5

Hot Cartridge

6

Cold Cartridge

7

Complete Hot Valve

8

9

Complete Cold Valve

10

Diverter Cartridge

11

Diverter Mounting Hardware

Complete Diverter

12

Hand Shower Mounting Hardware

13

Hand Shower Flange and

14

Guide Tube *

15

Hand Shower Unit *

16

Hand Shower Hose

17

Aerator Washer

18

Roman Tub Aerator without Restrictor

19

Aerator Housing *

20

Allen Key for Roman Tub Spout

21

* Please specify the finish when ordering the part.

PART

DESCRIPTION

Assembly *

Washer *

1212

1111

PART #

PS-5M00S

00CD

PH2210

KQ-5000S

P0416-SH

P0416-SC

P0491

P0492

P0500R

P0500

PM-Z11

Z-200-1

Z-200-2

Z-200-5

HS-600/ HS-700

PM-356

PM-355

P0255L

22

33

66

88

44

55

22

77

99

55

2121

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”

SPOUT INSTALLATION

1155CD _ _

1

- Remove the Quick Connect Spout Shank and Mounting Hardware from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.

- From the top of the deck, slip the quick Connect shank with the brass plate through the
assigned spout hole.

- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.

2.

- Remove the faucet from the box.

- From the top of the deck, slip the spout (1) with the flange(3) onto the quick connect shank
top. Align the spout and tighten the set screw with the Allen Key (21) provided.

3

- Connect the spout shank to one of the outlet port (OUT) of the diverter valve after the diverter
valve is installed. **

Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck

If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.

HANDLE INSTALLATION

Large Allen Key

Brass plate

Metal washer
Brass lock nut

Metal washer
Brass lock nut

1.

- Unscrew the pre-assembled handle trim (2) from the valve body.

- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout.

- From tub top, screw the Handle Flange back onto the valve. Do not tighten.
Insert the Handle Base of the handle trim (2) onto the valve stem and check for the handle height.
By turning the mounting lock nut, the handle base can be elevated or lowered accordingly.
After the height is set, tighten the mounting hardware (5)
Secure the Handle Base with the screw provided. Tighten firmly.

- Screw the Handle Top onto the Handle base. Tighten firmly.
Make sure that the handle turns freely in both directions.

2

- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection.

- Connect the water supply lines to the bottom inlets of the valve bodies. **

- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter
is installed. **

Handle Top

Screw

Handle Base

Handle Flange

Fiber washer

Brass lock nut

PAGE 02