Santec 1150LC User Manual
MONARCH CRYSTAL COLLECTION
ROMAN TUB FILLER WITH “LC” HANDLES
ITEM NUMBER
1150LC _ _-_ _
88
55
66
22
11
1212
1313
1414
22
33
77
44
99
55
1111
1515
1616
1010
##
Complete Spout Assembly *
1
Complete LC Lever Handle
2
Spout Flange *
3
Quick Connect Spout Shank & Hardware
4
Valve Body Mounting Hardware
5
Hot Cartridge
6
Cold Cartridge
7
Complete Hot Valve
8
9
Complete Cold Valve
10
Tee Connector
11
All Thread
12
Aerator Washer
13
Roman Tub Aerator without Restrictor
Aerator Housing *
14
15
Large Allen Key for Roman Tub Spout
16
Medium Allen Key for Handles
* Please specify the finish when ordering the part.
PART
DESCRIPTION
Assembly *
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
PART #
PS-5M00S
00LC
PH2210
KQ-5000S
P0416-LH
P0416-LC
P0493
P0494
P0340
P0341
PM-356
PM-355
P0255L
PAGE 01
INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”
SPOUT INSTALLATION
1
- Remove the Quick Connect Spout Shank and Mounting Hardware from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.
- From the top of the deck, slip the quick Connect shank with the brass plate through the
assigned spout hole.
- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.
2.
- Remove the faucet from the box.
- From the top of the deck, slip the spout (1) with the flange (3) onto the quick connect shank
top. Align the spout and tighten the set screw with the Large Allen Key (15) provided..
- Connect the spout shank to one of the outlet port of the handle valve bodies after the handle
trims and valve bodies are installed. **
Large Allen Key
Brass plate
Metal washer
Brass lock nut
1150LC _ _
Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck
If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.
HANDLE INSTALLATION
1.
- Using the Medium Allen Key(16) provided loosen the handle set screw.
- Unscrew the pre-assembled handle bell of handle trim (2) and the mounting hardware
from the valve body.
- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout.
- From tub top, insert the top mounting hardware back onto the valve. Do not tighten.
screw the handle bell of the handle trim (2) back onto the valve body. After the height of the
handle bell is set, unscrew the handle bell from the valve and tighten the top mounting hardware
firmly. Reinsert the handle bell and screw it tight against the valve’s cartridge thread.
- Insert the handle back onto the valve stem and tighten the set screw using the Medium Allen Key.
Make sure that the handle turns freely in both directions.
2
- Position the valve body side outlet towards the tee connector (10) for easier pipe connection.
Align the handle lever and tighten lock nut (5) firmly. Repeat the same procedure for the opposite side.
- Connect the water supply lines to the bottom inlets of the valve bodies. **
- Connect the valve body side outlet to the tee connector (10). **
Medium Allen Key
Metal washer
Brass lock nut
Handle Bell
Brass lock nut
Fiber washer
Fiber washer
Brass lock nut
Handle
** The spout, handle valve bodies and tee connector can be connected with flex hoses (not provide by Santec) or copper pipe
soldering. Please note that when soldering connections, do not use excessive heat. Excessive heat can damage the joints
increasing possibility of leakage.
PAGE 02
Loading...