Santec 1120TT User Manual

MONARCH COLLECTIONMONARCH COLLECTION

WIDESPREAD FAUCET WITH “TT” HANDLESWIDESPREAD FAUCET WITH “TT” HANDLES

ITEM NUMBER

1120TT _ _-_ _

##

11

22
33

44

1717
1818

1919

11

55

66

77

88

99

1010

33

22

22

1111
1212
1313
1414

1111

1515
1616
1717

SANTECSANTEC

44

1212

SANTECSANTEC

55

1818
1919

66

1414

1010

77

PARTPART

DESCRIPTIONDESCRIPTION

Complete Spout Assembly *Complete Spout Assembly *

Complete TT HandleComplete TT Handle

Spout Flange *Spout Flange *

Hot Cartridge OnlyHot Cartridge Only

Cold Cartridge OnlyCold Cartridge Only

Complete Hot ValveComplete Hot Valve

Complete Cold ValveComplete Cold Valve

Connecting Hose to the TeeConnecting Hose to the Tee

Connecting Hose to the SupplyConnecting Hose to the Supply

Tee ConnectorTee Connector

Spout Mounting HardwareSpout Mounting Hardware

Washer for the Tee ConnectorWasher for the Tee Connector

Allen Key for Handle Set ScrewsAllen Key for Handle Set Screws

Valve Body Mounting HardwareValve Body Mounting Hardware

Lift Knob and Lift Rod *Lift Knob and Lift Rod *

Complete Pop-Up *Complete Pop-Up *

Aerator WasherAerator Washer

Aerator Basket with RestrictorAerator Basket with Restrictor
Aerator Housing *Aerator Housing *

* Please specify the finish when ordering the part.* Please specify the finish when ordering the part.

Assembly *Assembly *

LineLine

FlangesFlanges

PART #PART #

PS-2M00SPS-2M00S

00TT00TT

PH2210PH2210

P0410P0410

P0411P0411

P0458P0458

P0459P0459

P0441P0441

P0440P0440

P0427P0427

P0431P0431

P0202P0202

PM-306PM-306

PM-305PM-305

P0952-UP0952-U

1414

1515

88

99

1313

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE

1616

PAGE 01

INSTALLATION INSTRUCTIONS

FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION

.

AFTER FLUSHING , SHUT OFF BOTH SUPPLY LINES.

MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM OF 1 1/2”

SPOUT INSTALLATION

1

- Remove the tee connector (10), spout mounting hardware (11) and tee connector
washer (12) from the bottom of the spout assembly. Apply a ring of silicon caulking
around the center hole on the top of the sink. Do not use plumbers' putty which
can damage the finish of the faucet.

- From the top of the deck, insert the spout's threaded shank through the center
hole of the sink.

2

- Slip the spout mounting hardware (11) back onto the spout. First the notched rubber
washer, then the notched metal washer and lastly the brass lock nut. Hand tighten the
lock nut

- Place the pop-up lift rod with the knob (15) through the back hole in the spout and
rotate the notched washers until the lift rod passes through the notch.

- Tighten the lock nut. Make sure the lift rod operates smoothly. Adjust it if necessary.

- Place the tee connector washer (12) into the tee connector (10) and thread the tee
connector onto the end of the spout shank. Tighten to seal.

- Align the spout and tighten the shank lock nut (11) firmly

HANDLE TRIM INSTALLATION

1120TT _ _

Notched rubber washer
Notched metal washer
Brass lock nut

Tee connector washer

Tee connector

1

- For proper handle turning direction, install the handle with the “cold” blue label (7)
at the right side of the spout (looking from the front) and the handle with the “hot”
red label at the left side of the spout.

- Both hot and cold side handle trims are pre-assmbled for faster installation.

- Remove the valve body mounting hardware (14) from the valve body. Slip the
valve body’s flexible hoses from the top of the sink or counter through the
appropriate hole next to the spout.
Aim the tee connecting hoses (8) toward the tee connector (10).

2

- From beneath of the basin or counter, screw the valve body mounting
hardware (14) back to the valve body. First the fiber washer, then the brass
lock nut.

- Tighten the lock nut until it secures the valve body firmly.

SANTEC SANTEC

SANTEC SANTEC

Fiber washer

Brass lock nut

PAGE 02