Sanken Electric Co SI-3090C Datasheet
●SI-3000C Series
SI-3000C Series
5-Terminal, Multi-Function, Full-Mold, Low Dropout Voltage Dropper Type
■Features
• Compact full-mold package (equivalent to TO220)
• Output current: 1.5A
• Low dropout voltage: VDIF≤1V (at IO=1.5A)
• Variable output voltage (rise only)
May be used for remote sensing
• Output ON/OFF control terminal is compatible with LS-TTL. (It may be
directly driven by LS-TTL or standard CMOS logic.)
• Built-in foldback overcurrent (SI-3033C: Drooping type overcurrent), overvoltage, thermal protection circuits
■Applications
• For stabilization of the secondary stage of switching power supplies
• Electronic equipment
■Absolute Maximum Ratings
Parameter
DC Input Voltage
Voltage of Output Control Terminal
DC Output Current
Power Dissipation
Junction T emper ature
Ambient Operating Temperature
Storage T emperature
Thermal Resistance (junction to case)
Thermal Resistance (junction to ambient air)
Symbol
VIN
VC
IO
PD1
PD2
Tj
Top
Tstg
Rth(j-c)
Rth(j-a)
Ratings
SI-3033C
20 35 35 45
SI-3050C/3090C SI-3120C/3150C
VIN
*2
1.5
18(With infinite heatsink)
1.5(Without heatsink, stand-alone operation)
–40 to +125
–30 to +100
–40 to +125
5.5
66.7(Without heatsink, stand-alone operation)
SI-3240C
(Ta=25°C)
Unit
V
V
A
W
W
°C
°C
°C
°C/W
°C/W
39
●SI-3000C Series
■Electrical Characteristics
Parameter
Input Voltage
SI-3000C
Output Voltage
SI-3000CA
Dropout Voltage
Line Regulation
Load Regulation
Temperature Coefficient
of Output Voltage
Ripple Rejection
Quiescent Circuit Current
Overcurrent Protection
Starting Current
*4,6
Control Voltage (Output ON)
Control Voltage (Output OFF)
VC
Terminal
Control Current
*5
(Output ON)
Control Current
(Output OFF)
*1
Symbol
∆VOLINE
∆VOLOAD
∆VO/∆Ta
RREJ
VC. IH
VC. IL
IC. IH
IC. IL
Conditions
Conditions
VDIF
Conditions
Conditions
Conditions
Conditions
Conditions
Conditions
Conditions
Conditions
Conditions
VIN
VO
Iq
IS1
(Ta=25°C unless otherwise specified)
Ratings
SI-3033C SI-3050C SI-3090C
min. typ. max. min. typ. max. min. typ. max.
*3
15
*2
*3
6
30
*2
10
*3
30
*2
3.168 3.300 3.432 4.80 5.00 5.20 8.64 9.00 9.36
3.234 3.300 3.366 4.90 5.00 5.10 8.82 9.00 9.18
VIN=5V, IO=1.0A VIN=8V, IO=1.0A VIN=12V, IO=1.0A
0.5 0.5 0.5
IO≤1.0A
1.0 1.0 1.0
IO≤1.5A
10 30 10 30 18 48
VIN=4.5 to 12V, IO=1.0A VIN=6 to 15V, IO=1.0A VIN=10 to 20V, IO=1.0A
40 100 40 100 70 180
VIN=5V, IO=0 to 1.5A VIN=8V, IO=0 to 1.5A VIN=12V, IO=0 to 1.5A
±0.5 ±0.5 ±1.0
VIN=5V, IO=5mA, Tj=0 to 100°CVIN=8V, IO=5mA, Tj=0 to 100°CVIN=12V, IO=5mA, Tj=0 to 100°C
54 54 54
VIN=5V, f=100 to 120HZ VIN=8V, f=100 to 120HZ VIN=12V, f=100 to 120HZ
310 510 510
VIN=5V, IO=0A VIN=8V, IO=0A VIN=12V, IO=0A
1.6 1.6 1.6
VIN=5V VIN=8V VIN=12V
2.0 2.0 2.0
0.8 0.8 0.8
20 20 20
VC=2.7V
–0.3 –0.3 –0.3
VC=0.4V
Unit
V
V
V
mV
mV
mV/°C
dB
mA
A
V
µA
mA
*1: "A" may be indicated to the right of the Sanken logo.
*2: VIN(max) and IO(max) are restricted by the relation PD(max)=(VIN-VO)•IO=18(W).
*3: Refer to the dropout voltage.(Refer to Setting DC Input Voltage on page 7.)
*4: IS1 is specified at –5(%) drop point of output voltage VO on the condition that VIN=VO+3V, IO=0.5A.
*5: Output is ON even when output control terminal VC is open. Each input level is equivalent to LS-TTL. Therefore, it may be directly driven by an
LS-TTL circuit.
*6: A foldback type ov ercurrent protection circuit is built into the IC regulator (e xcluding SI-3033C). Therefore, avoid using it for the follo wing applica-
tions as it may cause starting errors:
(1) Constant current load (2) Plus/minus power (3) Series power (4) VO adjustment by raising ground voltage
40
●SI-3000C Series
■Electrical Characteristics
Parameter
Input Voltage
SI-3000C
Output Voltage
SI-3000CA
Dropout Voltage
Line Regulation
Load Regulation
Temperature Coefficient
of Output Voltage
Ripple Rejection
Quiescent Circuit Current
Overcurrent Protection
Starting Current
*4,6
Control Voltage (Output ON)
Control Voltage (Output OFF)
VC
Terminal
Control Current
*5
(Output ON)
Control Current
(Output OFF)
*1
Symbol
Conditions
Conditions
Conditions
∆VOLINE
Conditions
∆VOLOAD
Conditions
∆VO/∆Ta
Conditions
RREJ
Conditions
Conditions
Conditions
VC. IH
VC. IL
IC. IH
Conditions
IC. IL
Conditions
VIN
VO
VDIF
Iq
IS1
(Ta=25°C unless otherwise specified)
Ratings
SI-3120C SI-3150C SI-3240C
min. typ. max. min. typ. max. min. typ. max.
13
*3
30
*2
16
*3
30
*2
25
*3
40
*2
11.52 12.00 12.48 14.40 15.00 15.60 23.04 24.00 24.96
11.76 12.00 12.24 14.70 15.00 15.30 23.52 24.00 24.48
VIN=15V, IO=1.0A VIN=18V, IO=1.0A VIN=27V, IO=1.0A
0.5 0.5 0.5
IO≤1.0A
1.0 1.0 1.0
IO≤1.5A
24 64 30 90 48 128
VIN=13 to 25V, IO=1.0A VIN=16 to 25V, IO=1.0A VIN=25 to 38V, IO=1.0A
93 240 120 300 120 300
VIN=15V, IO=0 to 1.5A VIN=18V, IO=0 to 1.5A VIN=27V, IO=0 to 1.5A
±1.5 ±1.5 ±2.5
VIN=15V, IO=5mA, Tj=0 to 100°CVIN=18V, IO=5mA, Tj=0 to 100°CVIN=27V, IO=5mA, Tj=0 to 100°C
54 54 54
VIN=15V, f=100 to 120HZ VIN=18V, f=100 to 120HZ VIN=27V, f=100 to 120HZ
510 510 510
VIN=15V, IO=0A VIN=18V, IO=0A VIN=27V, IO=0A
1.6 1.6 1.6
VIN=15V VIN=18V VIN=27V
2.0 2.0 2.0
0.8 0.8 0.8
20 20 20
VC=2.7V
–0.3 –0.3 –0.3
VC=0.4V
Unit
V
V
V
mV
mV
mV/°C
dB
mA
A
V
µA
mA
*1: "A" may be indicated to the right of the Sanken logo.
*2: VIN(max) and IO(max) are restricted by the relation PD(max)=(VIN-VO)•IO=18(W).
*3: Refer to the dropout voltage.(Refer to Setting DC Input Voltage on page 7.)
*4: IS1 is specified at –5(%) drop point of output voltage VO on the condition that VIN=VO+3V, IO=0.5A.
*5: Output is ON even when output control terminal VC is open. Each input level is equivalent to LS-TTL. Therefore, it may be directly driven by an
LS-TTL circuit.
*6: A foldback type ov ercurrent protection circuit is built into the IC regulator (e xcluding SI-3033C). Therefore, avoid using it for the f ollowing applica-
tions as it may cause starting errors:
(1) Constant current load (2) Plus/minus power (3) Series power (4) VO adjustment by raising ground voltage
41
Loading...