Sanken Electric Co SEL6514C Datasheet
Round-type contact mount LEDs (for automatic insertion)
3.5
0.8
±0.2
4.0
±0.2
0.4
±0.1
23.0min1.0min
(1.7) 3.5
±0.1
(P.2.54)
ø
3.1
±0.1
4.4
0.45
±0.1
0.65max
Resin heap
0.8max
Resin burr
0.3max
Cathode mark
Cathode
■SEL6010 series (Standard type)
SEL6210R
Absolute maximum ratings (Ta=25°C)
Symbol Unit Ratings
Top °C –30 to +85
Tstg °C –30 to +100
Outline drawing A
±0.5
Resin heap
0.8max
0.65max
±0.2
4.0
0.4
±0.2
0.8
±0.1
3.5
Cathode
(P.2.54)
23.0min1.0min 5.5
(1.7) 3.5
±0.1
0.45
IF mA 30
IFP mA 100
VR V3
±0.1
3.1
ø
±0.1
■SEL6014 series (Wide viewing angle)
SEL6414E
4.4
Outline drawing B
3.5
±0.2
±0.2
4.0
0.4
0.8
±0.1
Cathode
(P.2.54)
■SEL6015 series (Narrow viewing angle)
SEL6915A
Outline drawing C
23.0min1.0min 4.5
(1.6) 2.5
±0.1
0.45
0.65max
±0.5
±0.1
3.5
ø
Resin heap
0.8max
4.4
18
●SEL6000 series LEDs packaged on tapes can withstand
shocks caused by insertion machines; Thus, they can be con-
Recommended dimensions of
insertion holes on printed circuit boards
ø
0.9∼1.0
tact-mounted automatically on
circuit boards.
2.54mm
■External dimensions: Unit: mm Tolerance: ±0.3
Viewing angle
SEL6010 series SEL6014 series SEL6015 series
0°
30°
60°
050100% 50 100%
90°
30°
60°
90°
0°
30°
60°
90°
050100% 50 100%
Viewing angle of a non-diffused lens
0°
30°
60°
90°
Viewing angle of a diffused lens
050100% 50 100%
30°
30°
60°
60°
90°
90°
30°
60°
90°
Viewing angle of a non-diffused lens Viewing angle of a non-diffused lens
0°
30°
60°
050100% 50 100%
90°
Type No.
SEL6210R
SEL6210S
SEL6410G
SEL6410E
SEL6510G
SEL6510C
SEL6710Y
SEL6710K
SEL6810D
SEL6810A
SEL6910D
SEL6910A
SEL6214S
SEL6414E
SEL6514C
SEL6814A
SEL6914A
SEL6215S
SEL6415E
SEL6515C
SEL6815A
SEL6915A
Display
form
(ø: mm)
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.1
●3.5
●3.5
●3.5
●3.5
●3.5
●3.1
●3.1
●3.1
●3.1
●3.1
Type of lens
Red tinted, diffused
Red tinted, non-diffused
Green tinted, diffused
Green tinted, non-diffused
Green tinted, diffused
Un-tinted, non-diffused
Yellow tinted, diffused
Yellow tinted, non-diffused
Orange tinted, diffused
Orange tinted, non-diffused
Orange tinted, diffused
Orange tinted, non-diffused
Red tinted, non-diffused
Green tinted, non-diffused
Un-tinted, non-diffused
Orange tinted, non-diffused
Orange tinted, non-diffused
Red tinted, non-diffused
Green tinted, non-diffused
Un-tinted, non-diffused
Orange tinted, non-diffused
Orange tinted, non-diffused
Emitting
color
High intensity red
Green
Pure green
Yellow
Amber
Orange
High intensity red
Green
Pure green
Amber
Orange
High intensity red
Green
Pure green
Amber
Orange
typ
1.9
2.0
1.9
1.9
2.0
1.9
1.9
2.0
1.9
Electro-optical characteristics (Ta=25°C)
V
(V)
F
max
2.5
Condition
(mA)
10
IR
(µA)
IF
max typ
50 3
Condition
VR
(V)
(mcd)
50 32.5 10
50 32.5 10
IV
12
25
15
45
5
16
5
15
4
10
6.5
14
10
12
6
5
5
30
50
18
30
40
Condition
IF
(mA)
20
10
20
10
20
λp
(nm) typ
630
560
555
570
610
587
630
560
555
610
587
630
560
555
610
587
∆λ
35
20
40
35
33
35
20
35
33
35
20
35
33
Outline
drawing
A
B
C
■Using contact mount LEDs packaged on tapes
1. Printed circuit board ●One-side printed circuit board is recommended.
●If there are several SMD parts on the same printed circuit board, insert the LEDs after the adhesive for
other SMD parts hardened.
2. Insertion conditions ●Use low insertion pusher pressure, as much as possible.
●Cut and clinch: Panasert T pattern is recommended.
For N pattern, make the clinching angle of the LED’s anode as small as possible.
3. Soldering conditions ●Preheating must be less than 90°C (temperature on printed circuit board’s bottom surface) for no more
than two minutes
●Solder dipping must be made at a temperature of 250°C for no more than 3 seconds.
19
Loading...