Page 1
Heavy Duty
Upright
Vacuum Cleaner
Household Type
Owner’s Guide
600 Series
Index
Important Safeguards ...................... 2
Service Information .......................... 4
Assemble ......................................... 5
Use................................................... 7
Dust Bag .......................................... 8
Brush Roll Belt ................................. 9
Brush Roll ...................................... 10
Headlight .........................................11
For location of nearest Eureka/
Sanitaire Warranty Station or service
information call 1-800-282-2886.
www.eureka.com
Page 2
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug
the electrical cord when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used by or near
children.
• Use only as described in this manual. Use only manufacturer’s recommended
attachments.
• Do not use with damaged cord or plug. If v acuum cleaner is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, return it to a
service center before using.
• Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord
around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord
away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening b locked; k eep free
of dust, lint, hair, and anything that may reduce airflow.
• This vacuum cleaner creates suction and contains a rev olving brush roll. K eep hair,
loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is b urning or smoking, such as cigarettes, matches, or
hot ashes.
• Do not use without dust bag in place.
• Belt pulleys can become hot during normal use. To prevent burns, avoid touching
the belt pulley when servicing the drive belt.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use in
areas where they may be present.
• Store your cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
SA VE THESE INSTRUCTIONS
2
Page 3
CONSEILS DE SÉCURITÉ
Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent
être observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de b lessure:
• Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.
• Fermez le commutateur et débranchez l’appareil lorsque vous ne l’utilisez pas ou
avant le netto y a ge ou l’entretien.
• Ne permettez pas qu’il soit utilisé comme jouet. Une attention particulière est nécessaire
lorsque utilisé par ou près d’un enfant.
• Suivez les recommandations d’utilisation de ce manuel. Utilisez uniquement les
accessoires recommandés par le fabriquant.
• Ne pas utiliser si le cordon ou la fiche sont endommagés. Si l’aspirateur ne fonctionne
pas comme il le devrait, s’il a été échappé, s’il est endommagé, s’il a été laissé à l’e xtérieur
ou échappé dans l’eau, retournez-le à un centre de service avant de utiliser.
• Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de
poignée. Ne pas fermer une por te sur le cordon ou tirer le cordon sur des coins ou
bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le cordon à
distance des surfaces chauffantes.
• Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour
transporter le courant.
• Fermer tous les contrôles avant débrancher.
• Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le
cordon.
• Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.
• Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouv ertures sont bloquées;
assurez-vous qu’elles soient dégagées de poussière, mousse, che veux ou toute autre
chose qui pourrait réduire le passage de l’air.
• Cet aspirateur crée de la succion et contient un rouleau-brosse tournant. T enir les parties
mobiles et les ouvertures loin des cheveux, du linge, des doigts et de toute partie du
corps.
• Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumette ou
cendres chaudes.
• N’utilisez pas sans le sac de poussière en place.
• Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour
prévenir des brûlures, évitez de touché la poulie du courroie lorsque vous réparez la
courroie.
• Portez une attention particulière lorsque vous nettoyez les escaliers.
• Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de
l’essence: Ne pas utiliser dans les endroits où ces liquides pourraient être présents .
• Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.
• Maintenez un bon éclairage à l’endroit où vous tra vaillez.
• Débrancher les appareils électriques avant de les balayer.
CONSERVEZ CES INSTRUCTIONS
3
Page 4
To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche
polarisée (une des lames est plus large). Cette fiche ne peut être insérée dans une
prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,
retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire
installer une prise adéquate par un électricien qualifié. Ne pas modifier la fiche.
GENERAL INFORMATION
The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or
sharp objects with the cleaner to prevent bag tears, hose clogs, and f an blade breakage
with subsequent motor damage.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. For additional
service information telephone our toll free number for the nearest Eureka/Sanitaire
Authorized Warranty Station. You should know the model, type and serial n umbers
when you call:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main
Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company,
866 Langs Drive, Cambridge, Ontario N3H 2N7. Ref er to The Sanitaire Limited Warr anty
for complete service information.
DO NOT OIL the motor or the brush roll at any time. The bearings are
permanently lubricated and sealed.
Rating Plate
The model, type, and serial numbers are
indicated on the rating plate located on the
underneath side of the cleaner. F or prompt and
complete service information, always refer to
these numbers when inquiring about service.
Model & Type_________________________
Serial No.____________________________
4
MODEL TYPE SERIAL NO.
VOLTS AMPS. HERTZ
SERVICE INFORMA TION: 1-800-282-2886
Page 5
HOW TO ASSEMBLE
CAUTION: Completely assemble vacuum cleaner before using.
Assembly Packet
is with owner’s guide.
A
2-Part
Bolt
Step 1
Attach the Handle
Push the handle sections together. Note: Check
to be sure slots in handle are correct, see Detail
A.
Align the holes in the handle. Insert a 2-part
bolt (A) in the center of the handle and tighten.
Push handle into the handle socket so handle
grip curves away from the cleaner. Align the
holes, insert the other 2-part bolt (A) and tighten.
B
Upper
Cord Hook
B
C
C
Lower
Cord Hook
A
D
Bag
Screws
Detail A
A
D
5
Page 6
Step 2
Attach Upper Cord Hook
Pull the flexible cord support up toward the top
of the handle.
Insert the lower half of the cord support into the
upper cord hook.
Check to be sure slots in handle are correct,
see Detail A. Place inner tab of cord hook into
handle slot as shown (1) and press hook handle
(2) SNAPPING opposite inner tab into place (3).
1. Place inner tab
into slot
2. Press hook
around handle
3. SNAP opposite inner
tab into place
Step 3
Attach Lower Cord Hook
Insert the power cord into the lower cord hook.
Snap the hook into the lower handle.
Pull up on the cord to tighten but leave enough
slack near the base so there is no strain on the
cord when the handle is lower.
Step 4
Store Electrical Cord
Wrap the cord around the two cord hooks.
Fasten the plug to the electrical cord to prevent
unwinding.
B
Bag
Support
Hook
Flexible
Cord
Support
Upper Cord Hook
Step 5
Attach Outer Bag
Important: To provide a good gasket seal,
the bag coupling must seat
firmly against the motor base
and not overlap the furniture
guard.
Hold outer bag with zipper away from the handle.
Start the bag screws (D) by hand, then tighten
with a screwdriver.
Loop the bag spring onto the bag support hook
on the back of the upper cord hook.
6
Lower Cord Hook
Page 7
HOW TO USE
The upright vacuum cleaner is designed to be used on multiple types of carpeting. Do
not attempt to use the upright vacuum cleaner on bare floors, as damage to the
floor covering may result. Above the floor cleaning tools are available (optional).
1. Store
Handle Adjustment
With the tip of the foot, press down to
release the handle lock located at the left
rear side of the cleaner. Move the handle
and adjust it to the desired position for (1)
storing upright, (2) operating the cleaner at
a comfortable height for the user, and (3)
cleaning underneath low furniture.
Power Switch
The power switch is mounted on the motor
hood. A push with the foot turns the motor
ON; push again to turn the motor OFF.
Cord Storage
The cleaner has two convenient cord
storage hooks attached to the handle.
However, some models feature a quick
release cord hook on the upper handle. A
downward twist of the cord hook frees the
cord for quick removal. With either style,
wind the cord around the hooks for storage.
Fasten the plug to the cord to prevent
unwinding.
2. Use
3.Clean
Underneath
Handle Lock
ON/OFF
Cleaner Height Setting
WARNING: Avoid injury. Keep loose clothing, hair, fingers, and all other parts
of body away from any moving part (such as the revolving brush).
Turn off the switch and unplug the cleaner before changing the
cleaner height setting.
The front of the cleaner has an adjustment that
raises or lowers the cleaner base to match the
type of carpet. With the cleaner cord unplugged,
set the adjustment to lowest setting for maximum
cleaning. If the cleaner is difficult to push, mo v e
adjustment to next highest setting until cleaner
is comfortable to push. The brush roll must reach
the carpet for effective cleaning.
Make each adjustment with
cleaner switch off and cord
disconnected from outlet. For
ease in moving the adjustment
knob, place handle in operating
position and tilt cleaner back to
remove weight from front wheels.
7
Page 8
HOW TO MAINTAIN
The instructions given in this booklet serve as a guide to routine maintenance. To
avoid unnecessary service calls, check the bag, belt and brush roll often.
Disposable Dust Bags
Paper bags play a v ery important role in the efficiency of a vacuum cleaner. The purpose
of a paper bag is to trap dirt. But at the same time the paper bag must be porous
enough to allow air to pass through. If the paper bag becomes clogged, no air can
pass through the cleaner and no cleaning can take place, regardless of how powerful
the unit. Change the dust bag frequently. Some fine par ticles can restrict airflow very
quickly and will decrease performance even before the bag appears to be full. For that
reason, when vacuuming carpet fresheners or cleaners, powder, plaster dust, or similar
fine substances, the bag may need to be changed more often.
How To Change Disposable Dust Bag–Style F & G
NOTE: Turn off the switch and unplug the electrical cord before changing
dust bag. Never operate the vacuum cleaner without the dust bag.
THROAT
❛
4. Unfold
new
bag.
1. Pull
zipper
down.
TOP
2. Roll
down
BOTTOM
coil
spring.
3. Pull bag
throat off
sleeve.
5. Place bag
throat on
sleeve.
6. Roll up coil spring.
GENUINE
Look for the symbol.
EUREKA PRODUCT
7. Place paper bag into outer bag.
NOTE: Be certain there are no
folds at the top or bottom of the
paper bag.
Ask for GENUINE EUREKA
8. Lift zipper.
dust bags–Style F & G.
Micron Filter® Bag Care (Micron Filter Bag is standard on some models)
Because the Micron Filter Bag is an effective filter medium, occasionally tr apped dust
particles will need to be cleaned from the inside of it. The dust accumulation can be
vacuumed out with another vacuum or the bag may be removed to shake out. If you
desire, the bag may be hand laundered. The zipper on the bag should be down and
the bag should remain right side out. Use warm water (150°F 65°C) and a mild detergent.
Pre-soaking the bag in a laundry pre-soak is desirable for best cleaning results. Air dry
thoroughly before using.
DO NOT USE AN A UT OMATIC W ASHER OR DRYER as either will cause abrasion to
the delicate polyester fabric. DO NOT DRY CLEAN as dry cleaning fluids will damage
plastic parts of your bag assembly.
8
Page 9
Brush Roll Belt
The brush roll belt on the upright vacuum cleaner drives the brush to agitate, sweep,
and comb the carpet nap. The belt should be checked regularly to be sure it is in
good condition. Replace the belt if it is stretching, cracking, or slipping. Cut away
any hair or thread wound around the brush roll or the belt pulley because the buildup
could cause the belt to rotate unevenly.
How To Replace A Worn Belt
NOTE: Turn off the switch and unplug the electrical cord before replacing
belt. Belt pulleys can become hot during normal use . To prevent burns,
avoid touching the belt pulley when servicing the drive belt.
IMPORTANT: Improper installation of the brush roll or brush roll belt could
cause carpet or cleaner damage.
Motor
2
1
1
Pulley
1. Release cam locks.
Belt
Guide
4
3
Check for brush wear (see Brush Roll
instructions).
3. Place new belt around brush roll.
4. Align brush roll pulley with belt
guide.
7
7. Place lower side of belt into belt
guide and pull to stretch the belt
around the left side of motor pulley.
Rotate pulley to secure belt into
groove.
2. Pull up on belt to rotate it off the
motor pulley. Lift up on brush roll
and remove worn belt.
5
6
Metal Brush Roll only.
Place rubber end cap covers
(available on select models) over both
end caps (flat side against end cap).
Align holes and secure.
5. Slant brush roll forward so end
caps are in line with slots in cleaner
base .
6. Push brush roll into base.
9
8
9
8
Ask for GENUINE EUREKA
replacement belts, No. 52100
GENUINE
Look for the symbol.
EUREKA PRODUCT
8. Place slots of bottom plate over
tabs of cleaner base.
9. Seat and secure cam locks.
9
Page 10
Brush Roll
The rotating brush roll sweeps and combs the carpet nap. Keep the brush roll free
from hair and threads so it will continue brushing. When the bristles of the brush roll no
longer touch a straight edge held across the bottom plate, the brush roll is ineffective
because the bristles no longer touch the carpet nap. To maintain the most effective
cleaning, replace the wood brush roll. Install new brush strips on the chromed steel
brush roll (refer to instructions).
How To Replace Worn Brush Strips (chromed steel brush roll)
NOTE: Turn off the switch and unplug the electrical cord before replacing
brush strips.
New brush strips are supplied in sets of two, one long and one short. To replace,
remove bottom plate and belt (see How To Change Belt). Then, grasp center of brush
roll and lift to remove.
G
F
A B C D E
Note:
Shaft washer (D) not included in ball bearing brush roll assembly.
E
Slide in new brush strip of same
A.
Remove rubber end cap cover
(available on select models) from one
end.
B.
Unscrew locknut.
C.
Remove end cap.
D.
Remove shaft washer
(not included in
ball bearing brush roll).
Remove bearing retainer.
E.
Push shaft through opposite end.
F.
Pull out worn brush strip with pliers.
G.
When properly assembled, the brush roll should rotate freely between the two end
caps. Check the condition of the belt; change if necessary. Replace the brush roll, belt,
and bottom plate (see How To Replace A Worn Belt).
Ask for GENUINE EUREKA replacement brush strip.
12 inch No. 52282.
10
G.
length (rounded end first). Fit track on
either side into brush roll slot. Replace
second brush strip from opposite end
of brush roll.
Replace shaft.
F.
Align indentation on bearing retainer
E.
with brush strip on both ends of brush
roll.
Replace shaft washer.
D.
Position end cap with flat sides of
C.
center hole over flat sides of threaded
shaft.
Tighten locknut.
B.
Align holes and secure rubber end
A.
cap cover flat side against end cap.
Page 11
Headlight Bulb (Standard on most models)
NOTE: Turn off the switch and unplug the electrical cord before replacing
headlight bulb.
Headlight style varies by model. Locate the notches that release the tabs at either (1)
top, (2) side, or (3) bottom of the lens, as illustrated. Place a screwdriver into one
notch; twist or pry the screwdriver to release the lens. Repeat for the second notch on
the opposite side.
Rotate the bulb socket forward. Push bulb in and turn to remove. Secure new bulb into
socket and rotate bulb socket backward.
Replace the lens tabs into the top or the bottom of the hood opening. Rotate lens to
position and press down at each notch until the lens locks into position.
NOTE: Use 25 watt replacement bulb, only.
Ask for GENUINE EUREKA replacement bulb, 40009A.
1
3
2
Cleaner Care
NOTE: Turn off the switch and unplug the electrical cord before cleaning unit.
To keep the vacuum cleaner looking new , it can be wiped with a damp cloth and a mild
soap solution, then thoroughly dried. Never use any type of chemical as chemicals
can damage the cleaner. When not in use, the cleaner should be stored in a clean, dry
place.
11
Page 12
Part No. 57825A (4/02)
©1999 White Consolidated, Ltd.
Printed in U.S.A.
Loading...