Sangoma Vega 4x4 Installation Manual

FIELD UPGRADE

INSTALLATION MANUAL

Vega 4x4

MODULE INSTALL

4. MODULE ACTIVATION

The following steps will guide you through the software process to activate the

module and all its ports.

A) Log into your Vega 4x4 webGUI by typing its IP address inside the URL of a

browser of your choice

B) A window will pop up indicating there is a hardware change within the Vega.

This message is normal as the module was added.

C) A factory reset of the Vega 4x4 is required at this point to allow the unit to

fully detect the new ports. Click the 'factory reset' button visible near the

bottom of the window (See Diagram below).

A) A restore of your conguration is now required. Navigate to ‘System >

Conguration and click Choose File where it says ‘Send File to Gateway’ . A

window will pop up allowing you to search for the backup you previously

created (if you did not alter the name of the backup it will be called ‘cong.txt’)

B) Once selected click the ‘Upload’ button which will restore the Vega to previous

conguration

C) You will be required to Apply and Save settings

With the Vega now ready, you may now congure the new ports on your Vega 4x4.

Refer to the Vega 4x4 Quick Start Guide to continue conguration of the ports.

Sangoma.com © 2017 Sangoma Technologies Proprietary

100 Renfrew Drive, Suite 100, Markham ON L3R 9R6 Canada
[phone] or 1 800 388 2475 (toll free in N. America) [e-mail]

5. RESTORE YOUR CONFIGURATION

Note: Save your
existing conguration if
you have not done so,
as described in Step 2.
If you do not perform a
back up, your existing
conguration will be
lost.

Vega 4x4 Core Board

Vega 4x4 Board

Vega 4x4 Module

Thank you for purchasing the Vega 4x4 module. Based on your order, your package
includes 1 x FXO/FXS/Audio/GenGen module.

The following steps will guide you through the physical installation of the module
into the chassis of the Vega 4x4 as well as WebGUI reconguration to activate.

Your packaging will include the following:

• 1 x Module (FXS/FXO/Audio/GenGen)

NOTE: The mounting screws were included in the Vega 4x4 chassis packaging.

Note: For new Vega 4x4 installations without any user conguration, you may skip

this step and move to step 3.

To save a backup of the current conguration navigate to ‘System > Conguration’

and click Download. A window will prompt you to save cong.txt to your local

system (this is the complete backup of your Vega 4x4).

Preparation

A) Power down the Vega Gateway and remove the power cord from the unit.

B) Place the Vega Gateway on a at surface with the front of the unit facing
towards you

C) Verify the Vega Gateway is grounded.

D) Using a screwdriver remove the screws holding the top cover of the Vega
Gateway in place (see diagram 1)

E)

Remove the top cover by using light pressure and pressing down near the front

of the Vega Gateway and pushing toward the rear of the unit. (See diagram 2)

F)

With the cover removed the module slots are visible (see diagram 3)

Installation

A) Remove the module from its packaging and carefully identify the pins located
on the rear side .

B) Carefully align the module, over the pin connectors located on the Vega 4x4
board, on the rst available slot location (starting from the lowest port range
to highest), as seen in diagram 4.

C) Press rmly down on the module to insert . If the module is not tting, cease
pressure and attempt to re-alight before attempting again.

D) Once the module is seated in place locate the screw package (provided with
the chassis packaging) and insert them in the holes located at each corner of
the module, with a screw driver (see diagram 5)

E) Re-install the Vega Gateway cover by placing the cover ontop of the unit and
with light pressure slide to the front and lock in place.

F) Re-install the cover screws (see diagram 1). Do not over-tighten the screws to
avoid damaging the Vega Gateway.

1. REVIEW PACKAGE CONTENTS

2. BACKUP YOUR CONFIGURATION

3. INSTALL THE MODULE

Safety Warnings

Warning: The Vega 4x4 must be grounded before attempting the

below steps. (I.e., Touch unpainted metal to avoid destroying the
Vega Gateway with electrostatic discharge, work on non-carpeted
areas, etc.)

DO NOT ATTEMPT TO INSTALL THE MODULE WHILE THE VEGA 4x4 IS POWERED ON

Diagram 1 Diagram 2 Diagram 3

Diagram 4 Diagram 5