Page 1
IMPORTANT SAFETY INSTRUCTIONS
• To avoid injury or damage, mount only on a surface that is sturdy.
• To avoid electric shock, make sure the electricity is turned off at the main
circuit breaker panel. If you are replacing an existing fixture, turn off the
following in order: fixture, wall switch, and main fuse or breaker box.
Note: Some types of fuses must be unscrewed to shut the power off.
• If you are unclear as to how to proceed, please consult a licensed
electrician.
UNPACK THE FIXTURE: Check the contents of the box. Box should contain all items on the parts diagram.
INSTALLATION INSTRUCTIONS
1. Secure Mounting Plate (A) to the junction box (not included) using Mounting Screws (B) provided. Ensure
the attached Screw Collar Loop (E) is pointing down towards the floor.
2. Remove Threaded Ring (F) from Screw Collar Loop (E) by unscrewing it in a counter-clockwise direction.
Set Threaded Ring (F) aside.
3. Place Canopy (D) against the ceiling with Screw Collar Loop (E) protruding through the hole in Canopy (D).
Adjust Screw Collar Loop (E) and the hex nut above it until 3/8" of the threaded portion of Screw Collar
Loop (E) is visible. Remove Canopy (D) and set it aside.
4. Secure both Downrods (L) together and secure them to the top of Socket Assembly (K). Secure Center
Connector (I) to the top of Downrods (L). Pull through any necessary Wire (H).
5. Spread out arms on Fixture Body (J) evenly to create the chandelier design.
6. Remove Hook Cap (N) from Hook (P). Line up the holes on Ring (Q) with the holes on Fixture Body (J).
Thread Hook (P) through the holes of Fixture Body (J) and Ring (Q), ensuring Hook (P) is on the inner side
of Fixture Body (J). Secure in place with Hook Cap (N). Do this for the remaining 3 sides.
Note: Make sure the opening from Hooks (P) is facing upwards.
7. Place Socket Assembly (K) within Fixture Body (J) and secure Arms (M) to Hooks (P) and Center Connector
(I). Spread out the sockets on Socket Assembly (K) evenly. Set aside.
Page 2
8. Assemble one end of Chain (G) to the loop on Center Connector (I) by opening Quick Link (O) closing it
around the loop.
9. With chain pliers, remove excess Chain (G) to achieve desired hanging length. Once Chain (G) is cut, use
wire cutters to cut Wire (H) 10” beyond the length of Chain (G) to allow for easier wire connection.
10. Weave Wire (H) upwards through every 4-5 links in Chain (G).
11. Slide Threaded Ring (F) down Chain (G) and Wire (H) with the raised end (flange) facing up towards the
ceiling. Slide Canopy (D) down Chain (G) and Wire (H).
12. Carefully lift the fixture (with the help of a friend). Secure top of Chain (G) to Screw Collar Loop (E) with
Quick Link (O).
13. Insert the end of Wire (H) through the hole in Screw Collar Loop (E) into the junction box.
14. Using the wire graph below, connect the appropriate wires from the fixture to the corresponding wires in
the electrical junction box (not included) and secure Wire Connectors (C).
A. Connect the ground wire (bare copper or green) from
your fixture to the:
1) ground wire in the junction box, or
2) ground screw in the junction box
B. Connect the BLACK house wire to fixture hot wire
that corresponds to diagram (black, round &
smooth, white/grey with tracer, brown/gold without
tracer).
C. Connect the WHITE house wire to fixture neutral wire
that corresponds to diagram (white, ribbed/ridged,
white/grey without tracer, brown/gold with tracer).
15. Place all Wire (H) and Wire Connectors (C) back into the junction box.
16. Slide Canopy (D) and Threaded Ring (F) up Chain (G) and Wire (H). Place Canopy (D) flush against the
ceiling and secure in place by screwing Threaded Ring (F) onto Screw Collar Loop (E) in clockwise direction.
17. Install bulbs (not included) into the sockets on Socket Assembly (K).
Enjoy your new fixture!
Page 3
HELPFUL TOOLS: Safety Goggles, Screwdriver, Wire Cutter/Stripper, Ladder, Measuring Tape, Chain Pliers
Loading...