WARNING (To reduce the risk of fire, electric shock, or injury to
persons):
1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go
to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B).
Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any
gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur.
It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT：
TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture
Page: - 1 - / 3
PARTS TYPE & QTY INCLUDING:
(B) Mounting plate assembly (1)
(D) Green ground screw (1)
(E) Back plate (1)
(F) Threaded ball (2)
(G) Glass (1)
ACCESSORIES & QTY ENCLOSED:
(A) Plastic Wire Connectors (3)
(C) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in
the above illustration .
2. Turn off power
Before you start to make installation, NEVER attempt any work without shutting off the
electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. B). Place the wall switch in the
“OFF”position.
3. Unscrew the threaded balls (F) from the back plate (E)
then carefully remove the mounting plate assembly (B).
4. Carefully and gently pass the outlet box wires through
the mounting plate assembly(B).
Attach the mounting plate assembly (B) to wall with
mounting screws (C).
Page: - 2 - / 3
6. Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF
FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE
Connect ground wire according to below chart Connect wires according to below chart
Twist plastic wire connector until wires are tightly joined together,wrap each connector with approved electrical
tape and carefully tuck all wires into the outlet box .
7. Align the holes in the back plate (E) with the mounting screws,
then attach the back plate (E) using the previously removed threaded
balls (F). Hand tighten until snug.
Note: The back plate (E) should be snug against the
wall and the threaded balls. If not, adjust the length
of the nipples on the mounting plate assembly (B) by
unscrewing the preassembled hex nuts and then screwing
the mounting screws in or out of the mounting plate until the
length is achieved. Tighten the hex nuts and proceed to the step 7
8. Install bulbs (Not included. Please do not exceed the maximum
capacity recommended on the socket.)
Thread the glass (G)into the lantern till tight。
9. Check everything is already installed properly, then you could turn on the light. Enjoy!
CLEANING
To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool
or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can
be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
Page: - 3 - / 3
Loading...