Page 1
Patio Set
ATTACH YOUR
RECEIPT HERE
Keep a copy of your proof of
purchase or order confirmation
which will be needed if you need to
contact us about warranty coverage.
Purchase Date:
SAVE THESE
INSTRUCTIONS FOR
FUTURE REFERENCE.
Questions, problems, missing parts?
Before returning to your retailer, our exceptional customer service is available.
Call us toll-free , email us, or go online and live chat .
Page 2
INFORMATION
BEFORE YOU BEGIN
Before beginning assembly, make sure all parts are present. Compare parts received with the parts list. If any part
is missing or damaged, do NOT attempt to assemble the product. Please read and understand this entire manual
before attempting to assemble, operate or install this product. If you have any questions regarding the product,
please call us toll-free , email us , or go online and live chat.
GENERAL INFORMATION
Your new Patio Set is made from the finest materials available. It should provide years of enjoyment with
minimal care.
Keep your Patio Set clean. For best results, clean with a soft, damp cloth. You may use a standard glass
cleaning spray to clean the glass tabletop. If you use furniture covers, always make sure the Patio Set is clean
and completely dry before covering, as mold may form in dark, wet places. Remove cushions prior to
covering and store them in a dry, temperature controlled place. Check the hardware on your Patio Set
regularly to make sure it is secure.
The weight limit is 220 lb/100kg per chair, 440 lb/200kg total for sofa.
SAFETY INFORMATION
WARNING
Do not stand or allow children to stand on the assembled product. Ensure hardware is securely in place. Perform
periodic checks to make sure the connections are secure and adjust if needed. The glass tabletop is tempered for
strength but may break or chip if dropped, struck sharply, or otherwise abused. Do not sit or stand on the glass
tabletop, and take reasonable precautions to avoid injury in the event of glass breakage.
CAUTION
Read all instructions before beginning assembly. Failure to do so may result in faulty assembly and potential
injury. Assemble the item on a soft, non-abrasive surface such as carpet or cardboard to avoid damaging the
item.
2
Page 3
PARTS LIST - PER CHAIR (A & B)
PART DESCRIPTION QUANTITY
A
B
C
D
A
B
C
D
E
Left* Side Panel 1
Right* Side Panel 1
Seat Panel 1
Back Panel 1
Seat Cushion 1
*When facing the front of the chair
HARDWARE CONTENTS
F
M6x25 Bolt
Qty: 6
G
M6x35 Bolt
Qty: 4
H
Washer
Qty: 100
E
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
Hex Key
3
Page 4
ASSEMBLY - CHAIR (A & B)
4
Locate the Right Side Panel B and Seat Panel C. Place a
Washer H on each of 3 Bolts F. Align the panels as
1
shown. Insert each Bolt with Washer through the eyelets
in the Seat Panel and into the holes in the edge of the
Right Side Panel.
Tighten using the Hex Key, but do not over-tighten.
Hardware Used:
Attach the Back Panel D to the Right Side Panel B:
Place a Washer H on each of 2 Bolts G. Align the
2
eyelets on the Back Panel with the holes in the Right
Side Panel as shown, then insert a Bolt with Washer
into each of the 2 aligned sets of eyelets.
Bolt (M6x25) x3
F
Washer x3
H
B
C
G
D
F
H
x 3
C
Tighten using the Hex Key, but do not over-tighten.
Hardware Used:
Locate the Left Side Panel D. Place a Washer H on
3
each of 2 Bolts G. Place the partially-assembled chair
on the Left Side Panel as shown. Align the eyelets on the
Back Panel with the holes in the Left Side Panel and
insert a Bolt with Washer through each of the 2 aligned
sets of eyelets.
Tighten using the Hex Key, but do not over-tighten.
Hardware Used:
Bolt (M6x35) x2
G
Washer x2
H
Bolt (M6x35) x2
G
Washer x2
H
x 2
A
C
H
B
B
G
D
H
x 2
Page 5
ASSEMBLY - CHAIR (A & B)
5
Place a Washer H on each of 3 Bolts F. To attach the
4
Left Side Panel C to the Seat Panel B, insert a Bolt
with Washer into the 3 aligned sets of eyelets.
Tighten Bolts using the Hex Key, but do not overtighten.
Hardware Used:
Turn assembled chair upright on a flat, level surface to
ensure that it sits squarely and level on the ground.
5
Adjust fastenings if needed, then firmly tighten all Bolts.
Place the Seat Cushion in the seat.
F Bolt (M6x25) x3
H Washer x3
F
H
x 3
B
C D
A
E
Your Chair is fully assembled!
Repeat these steps to assemble the second chair.
Page 6
PARTS LIST - SOFA (C)
6
PART DESCRIPTION QUANTITY
A
B
C
A
B
C
D
E
Left* Side Panel 1
Right* Side Panel 1
Seat Panel 1
Back Panel 1
Seat Cushion 1
*When facing the front of the sofa
HARDWARE CONTENTS
F
M6x25 Bolt
Qty: 8
G
M6x35 Bolt
Qty: 44
H
Washer
Qty: 12
D
E
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
Hex Key
Page 7
aSSEMBLY - SOFA (C)
7
Locate the Right Side Panel B and Seat Panel C. Place a
Washer H on each of 3 Bolts F. Align the panels as
1
shown. Insert each Bolt with Washer through the eyelets
in the Seat Panel and into the holes in the edge of the
Right Side Panel.
C
F
Tighten using the Hex Key, but do not over-tighten.
Hardware Used:
Attach the Back Panel D to the Right Side Panel B:
Place a Washer H on each of 2 Bolts G. Align the
2
eyelets on the Back Panel with the holes in the Right
Side Panel as shown, then insert a Bolt with Washer
into each of the 2 aligned sets of eyelets.
Tighten using the Hex Key, but do not over-tighten.
Hardware Used:
Bolt (M6x25) x3
F
Washer x3
H
Bolt (M6x35) x2
G
Washer x2
H
B
x 2
H
x 3
D C
G
H
B
D
Fasten the Back Panel D to the Seat Panel C:
Place a Washer H on each of 2 Bolts F. Insert each
3
Bolt with Washer into one of the 2 aligned sets of
eyelets on the underside of the Seat Panel.
Tighten using the Hex Key, but do not over-tighten.
Hardware Used:
Bolt (M6x25) x2
F
Washer x2
H
H F
x 2
C
B
Page 8
ASSEMBLY - SOFA (C)
8
Locate the Left Side Panel D. Place a Washer H on
each of 2 Bolts G. Place the partially-assembled sofa
4
on the Left Side Panel as shown. Align the eyelets on
the edge of the Back Panel with the holes in the Left
Side Panel and insert a Bolt with Washer through
each of the 2 aligned sets of eyelets.
Tighten Bolts using the Hex Key, but do not overtighten.
B
C D
G
H
Hardware Used:
Place a Washer H on each of 3 Bolts F. To attach the
Left Side Panel C to the Seat Panel B, insert a Bolt
5
with Washer into the 3 aligned sets of eyelets on the
underside of the Seat Panel.
Tighten Bolts using the Hex Key, but do not overtighten.
Hardware Used:
Turn assembled sofa upright on a flat, level surface to
6
ensure that it sits squarely and level on the ground.
Adjust fastenings if needed, then firmly tighten all Bolts.
G Bolt (M6x35) x2
H Washer x2
F Bolt (M6x25) x3
H Washer x3
A
x 3
E
A
x 2
B
C
D
Place the Seat Cushion E in the seat.
Your Sofa is fully assembled!
Page 9
PARTS LIST - TABLE (D)
9
PART DESCRIPTION QUANTITY
A
B
C
A
B
C
D
Glass Tabletop 1
Table Frame 1
Leg 4
Shelf 1
HARDWARE CONTENTS
E
M6x15 Bolt
Qty: 12
F
Washer
Qty: 12
D
Hex Key
Assemble in a clear area on a spacious, nonabrasive surface such as a carpet or blanket. Wait to fully tighten hardware
until final step. Do not over-tighten hardware.
Page 10
ASSEMBLY - TABLE (D)
10
Place the Table Frame B upside-down on a protected
surface (Bolt holes will be visible at each corner). Place a
1
Washer F on each of 8 Bolts E.
Position a Leg C at the corner of the Table Frame as
shown, aligning the eyelets in the top plate of the Leg
with the threaded holes in the Table Frame. Insert a Bolt
with Washer into each of the the aligned sets of eyelets.
Repeat to install remaining 3 Legs.
Tighten Bolts with the Hex Key, but do not over-tighten.
Hardware Used:
Place a Washer F on each of 4 Bolts E. Position the
Shelf between the installed Legs as shown, then insert a
2
Bolt with Washer through each bracket eyelet and into
the threaded holes in the bottom of the Shelf.
Tighten Bolts with the Hex Key, but do not over-tighten.
E Bolt (M6x15) x8
F Washer x8
C C
C
B
E
F
E
F
x 4
D
Hardware Used:
Turn assembled table upright on a flat, level surface to
ensure that it sits squarely and level on the ground.
3
Adjust fastenings if needed, then firmly tighten all Bolts.
Carefully place the Glass Tabletop A on the Table
Frame.
Your Table is fully assembled!
E Bolt (M6x15) x4
F Washer x4
x 4
A
Page 11
1 YEAR LIMITED WARRANTY
Customers in the Contiguous US
All components are warranted for a period of 1 year after date of purchase
by the original owner against defects in materials and workmanship under
normal use. This warranty does not cover normal wear and weathering,,
assembly and/or maintenance or use in a commercial application if model
is not designated as a commercial model. At our sole discretion, products
under warranty will be repaired and/or replaced at no charge to the
customer. In returns sent back to us must be sent via prepaid freight and in
the original retail packaging.
For warranty service contact us at the address, phone numbers or internet
site and email listed in this owner’s manual. Be sure to have your sales
receipt, date of purchase and catalogue/model numbers available when
calling. All warranty service will be coordinated by service center.
This warranty is extended only to the original purchaser. Proof of purchase
will be required before warranty service is rendered. The sales receipt is
the only valid proof of purchase. This warranty only covers failures due
to defects in materials or workmanship which occur during normal use.
Failures and/or damage which result from accident, negligence, misuse,
abuse, neglect, mishandling,,alteration, or modification, failure to maintain,
improper assembly or maintenance, service by unauthorized agency, use
of unauthorized components, or damage that is attributable to acts of God
are NOT covered.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION. THE PROVISIONS
OF THE UNITED NATIONS CONVENTION ON CONTRACTS FOR THE SALES OF GOODS
SHALL NOT APPLY TO THIS LIMITED WARRANTY OR THE SALE OF PRODUCTS COVERED BY
THIS LIMITED WARRANTY.
•THERE ARE NO EXPRESS WARRANTIES EXCEPT
AS LISTED HERE
•PURCHASER ASSUMES ALL RISKS IN THE
ASSEMBLY AND OPERATION OF THIS UNIT
•FAILURE TO FOLLOW WARNINGS AND
OPERATIONAL INSTRUCTIONS CONTAINED IN
THIS MANUAL CAN RESULT IN SEVERE PROPERTY
DAMAGE AND/OR PERSONAL INJURY
•IN NO EVENT WILL DIRECTORS, OFFICERS OR
AGENTS BE LIABLE TO THE PURCHASER OR ANY
THIRD PARTY, WHETHER IN CONTRACT, IN TORT,
OR ON ANY OTHER BASIS, FOR ANY INDIRECT,
SPECIAL, PUNITIVE, EXEMPLARY,
CONSEQUENTIAL, OR INCIDENTAL LOSS, COST,
OR DAMAGE ARISING OUT OF OR IN
CONNECTION WITH THE SALE, MAINTENANCE,
USE, OR INABILITY TO USE THE PRODUCT, EVEN
IF DIRECTORS, OFFICERS OR AGENTS HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES,
COSTS OR DAMAGES, OR IF SUCH LOSSES,
COSTS, OR DAMAGES ARE FORESEEABLE. IN NO
EVENT WILL OFFICERS, DIRECTORS, OR AGENTS
BE LIABLE FOR ANY DIRECT LOSSES, COSTS OR
DAMAGES THAT EXCEED THE PURCHASE PRICE
OF THE PRODUCT.
•SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO
THE PURCHASER.
Important Notice
Do NOT return to place of purchase—for customer service and warranty issues contact our
customer service center, email us, or goonline and live chat.
All rights reserved.
Loading...