Page 1
Assembly Instruction Sheet
ToolsRequired:
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifany partsaremissing ordamaged,do notattemptto assemble,install,or operatethefixture. Contactcustomerservice forreplacement
parts.
Fixturecanonly bemountedin thedirectionindicated onpage2.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wire cutters,wirestrippers, electricaltape,safety glasses.
(1)A19 MediumBaseBulb 100WMaximum
30-45minutes
Identifyandinspect allpartsbefore beginninginstallation.Check packagecontentlist anddiagramsbelow tobesure allpartsare
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
B
x1
Alternate
Mounting
C
Fixture Body
A
x1
STEP 1 Instal Shade-
Unscrew the Lock Screw, remove the Cage, the Glass Shade and
A.
the Tab from the Fixture Body ( ).
inside of the shade.
B. Place Glass Shade into the Cage, secure by place the Tab into the
Cage press on the Glass Shade.
C. Align the label “A” on the bottom of the fixture hood to the label “A”
on the top edge of the cage. Place the fixture hood onto the top
edge of the cage and secure with lock screws. Hand tighten until
snug with screwdrivers.
A Remove the Styrofoam from
screw
x2
Fixture Hood
Label “A”
Tab
Glass Shade
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (B). Attach
the Crossbar Assembly (B) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use theAlternate Shorter Mounting Screw (C) if your
installation requires a shorter mounting screw.
Outlet Box
Mounting Screw
or Alternate Short
Mounting Screw
STEP 3 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (B). Place
the backplate and Fixture Body (A) onto the CrossbarAssembly (B)
and secure with mounting balls. Note: The backplate and Fixture
Body (A) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
or alternate short mounting screws on the Crossbar Assembly (B)
by unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws
in or out of the crossbar until the correct length is achieved. Once
the backplate and Fixture Body (A) is secure, remove the mounting
ball and Fixture Body (A) and proceed to Step 4.
.
Outlet Box Screws
(not included)
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
Supply Wires with
Ground Wire
B
Backplate
Mounting Ball
Figure 1
Label “A”
Lock Screw
Cage
1of2
Figure 3
B
Hex Nut and
Lock Washer
A
Page 2
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Bare, or Green
Ground wire
from outlet box
OR
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Ground wire
from fixture
Green Ground Screw
on the Crossbar
Figure 4
STEP 5 Install the Fixture Body-
A. Position the backplate and Fixture Body (A) onto the Crossbar
Assembly (B). Place the holes in the backplate over the mounting
screws. Secure the backplate and Fixture Body (A) by using the
mounting balls and hand tighten the mounting balls until snug.
Mounting Screw
or Alternate Short
Mounting Screw
Backplate
Mounting Ball
FINISH: FRESCO
6.5”
Fixture can
only be
mounted in
the direction
indicated
4.5”
8”
7” Dia.
11”
B
A
Figure 5
STEP 6 - Install the Bulb and Apply Silicone Sealer
A. Insert the bulb onto socket and screw snugly into place.
B. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over
top of backplate and down
both sides. Do not caulk the
bottom of the fixture
Exterior
Grade Caulk
backplate to ensure proper
moisture drainage.
Socket
Your fixture is now
assembled and ready to
use. Enjoy!
Exterior
Grade
Caulk
Backplate
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
Figure 6
Bulb (not
Supplied)
2of2
Loading...