Page 1
Assembly Instruction
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)A21 MediumBase bulb150W Maximumor
(1)MediumBaseVintagebulbisrecommendedbutnotsupplied.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
Package Contents
Glass Holder
Mounting Screw
A
x3
Fixture Hood
B
x1
STEP 1 - Install Bulb and Glass Shade
A. Insert the bulb onto the socket and screw snugly into place.
B. Place the Glass Shade (E) over the bulb carefully.Attach the shade
neck to the fixed shade holder on the Fixture Body (B). With one
hand holding the Glass
Shade (E), place the Glass
Holder (C) to other side of
shade neck and place it over
bolts on the fixed glass
holder. Secure them together
by threading Lock Balls (D)
onto bolts. Hand tighten until
snug.
Fixed Shade
Holder
C
Lock Ball
D
x2
B
x1
E
Bolt
Glass
Shade
x1
C
D
Neck
E
STEP 2 - Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Post Lighting
Fixture
Fitter
Post
STEP 3 M C
EM H
A. Remove the light fixture. Using
STEP 4 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
- arking the enter of
ach ounting ole
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
post at each (3) locations marked in step 5 above.
Marking Pen
Mounting
Hole
Figure 2
Center Punch
1/16” bit and drill
Fixture
Fitter
Post
Figure 3
Hammer
Marking
Post
Figure 1
E
1of2
Figure 4
Post
Page 2
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Figure 5
STEP 6 Attach the fixture to the Post Mount-
A. Place the fixture on the post lining up the mounting holes on the
fixture fitter with the holes on the post. Use the Mounting Screws (A)
to attach the fixture to the post.
Your fixture is now assembled and ready to use. Enjoy!
Post Lighting
Fixture Fitter
Mounting Hole
FINISH: WESTERN BRONZE
11”
26.5”
12.75”
13.25”
Figure 6
A
Post
9.25” Dia.
Hole
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
2of2
Loading...