Page 1
Assembly Instruction
ToolsRequired: Flathead screwdriver, Phillips screwdriver,pliers, wire cutters, wire strippers,electrical tape, safety glasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.If any parts are missingor damaged, do not attemptto assemble, install, or operatethe fixture. Contact customer servicefor replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)A21 MediumBasebulb 150W Maximum or
(1)Medium Base Vintage bulb is recommendedbut not supplied.
20-30minutes
Identifyand inspect all parts beforebeginning installation. Check package contentlist and diagrams below toensure all parts are
Package Contents
Fixture Loop
A
x1
Fixture Body
B
x1
Crossbar
AA
Assembly
x1
CC
STEP 1 Install Fixture Loop and
Bulb
A. Thread the Fixture Loop (A) onto the
B. Insert the bulb onto the socket and
-
top center of the Fixture Body (B)
and hand tighten until snug.
screw snugly into place.
Glass Holder
C
x1
Lock Ball
D
x2
Glass
E
Shade
x1
Hardware Contents
Fixture Chain
BB
x1
Quick Link
x2
A
B
DD
Ceiling
Canopy
x1
STEP 2 Install Glass Shade-
A. Place the Glass Shade (E) over the bulb carefully. Attach the shade
neck to the fixed shade holder on the Fixture Body (B). With one hand
holding the Glass Shade (E), place
the Glass Holder (C) to other side of
shade neck and place it over bolts on
the fixed glass holder. Secure them
together by threading Lock Balls (D)
onto bolts. Hand tighten until snug.
Fixed Shade
Holder
Figure 2
STEP 3 - Install the CrossbarAssembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug.
Outlet Box
B
D
Neck
Bolt
E
E
C
Socket
Vintage Bulb
(recommended
but not supplied)
Figure 1
1of2
AA
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Figure 3
Green Ground Screw
Nipple
Canopy Chain Loop
DD
Canopy Lock Ring
Page 2
(Step 3 Continued)
STEP 5 - Making the Wire Connections
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the canopy lock ring from the canopy chain loop. Place the
Ceiling Canopy (DD) over the canopy chain loop against the ceiling
to determine the correct position of the nipple. Thread the canopy
lock ring onto the canopy chain loop. Adjust the nipple to allow the
Ceiling Canopy (DD) to rest against the ceiling when held in place by
the canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
STEP 4 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (BB) to your desired length by removing
links if needed. Put a cloth over the Fixture Chain (BB) to protect the
finish.
B. Pull the supply wires through the Fixture Chain (BB) alternating
links. After the wires are through the Fixture Chain (BB), pull the
Supply Wires and the Ground Wire through the canopy lock ring and
the Ceiling Canopy (DD) in order.
C. Attach one end of the Fixture Chain (BB) to the fixture loop with one
Quick Link (CC). Lift the fixture and Fixture Chain (BB) up and attach
the other end of the Fixture Chain (BB) onto the canopy chain loop
with another Quick Link (CC). The fixture will now hang safely.
D. Feed the Supply Wires and Ground Wire through the canopy chain
loop and nipple into the outlet box. Cut the wires leaving
approximately 8” of wire extending from the Outlet Box.
E. Go to Step 5 for wire connections and follow the directions. Return
to Step F in this step when complete with Step 5.
F. Raise the Ceiling Canopy (DD) and canopy lock ring up the Fixture
Chain (BB) and over the canopy chain loop. Tighten the canopy lock
ring onto the canopy chain loop until tight.
Suggested chain length for Ceiling height :
8’ ceiling : use 10 links of chain and 2 quick links
9’ ceiling : use 20 links of chain and 2 quick links
10’ ceiling : use 30 links of chain and 2 quick links
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B.
Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
on the Crossbar
White wire from fixture
identified with the Label “N”
Black wire from fixture
identified with the label “L”
Ground wire
from Fixture
Figure 5
Your fixture is now assembled and ready to use. Enjoy!
5” Dia.
FINISH: WESTERN BRONZE
Supply Wires and
Ground Wire
BB
Figure 4
Nipple
Canopy Chain Loop
CC
DD
Canopy Lock Ring
CC
Fixture Loop
13.25"
9.25" Dia.
123.25” OVERALL
HEIGHT INCLUDES
96” CHAIN AND
2 QUICK LINKS()
21.5"
11" Dia.
2of2
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
Loading...