Samzuk Technology Development Co FTAN20AA User Manual

Instruction Manual

Digital Wireless Intercom SAMCOM FTAN20AA

Features of Model FTAN20AA

Simple to use" Instant" Intercom system.
Individually call and Group call function.
Connect ability to other hand held two way radio.

Sancon Inc.

1. Get Acquaint
Description of Buttons and Keys

ABC Switch DC Input (Mini USB)

Antenna

LCD Unit

LOCK KEY TALK KEY GROUP KEY Mic

10 Keys

2

Display symbols and icons

Selective icon Power On icon

Channel icon ABC icon

Group icon VOL icon

FTAN20AA SETUP INSTRUCTIONS

3

Step 1 TURN ON THE UNIT

1) Fully insert the power cord

2) Check if the switch is on "A" position

(2)

Step 2 SETTING GROUP NUMBER & CHANNEL NUMBER FOR EACH UNIT

You should set Group Number and Channel Number when you get these intercoms.
Normally no need to change the Group Number , Unless you found your neighbor has used
This number ( you can hear neighbor's speaking or they can hear from you when using)
Below is the process way for setting Group Number and Channel Number

The default group number for all units is" 0" (factory setting),you can decide wether to change
It or not

1) To keep pressing the key "-" for 5 seconds, you will hear "DU DU" sound ,meanwhile the
LCD display is " Group Call 0 " and "0" will keep flash.

2) Then you can press different number as your new Group Number from 0 to 19, be sure to keep

(1)

All the units updated to the same new Group number . if you do not change factory setting 0,
Then you can set change number after you press any of the “ LOCK/ TALK/ GROUP ”button.
When you have finished Group setting, the intercom automatically entered into the channel s

3) The default channel number is No.1 for all units (factory setting) you can set different Number

4

For each unit if you buy over 2 units, if only two units, no need to set.

b

After group setting finished, the display will change to " Channel 1" and "1" will keep flash.

4) You can choose new number from 0-19 as separate unit's channel number, of cause
GROUP Number can’t be choice again. Then the new number will keep flash.

5) Press any of the LOCK, TALK or GROUP button once again then the display will show new
channel number and digit number is not flash. Congratulation, you have successes set the unit's
Group Number and Channel Number.

Keep the same way for the balance unit's channel setting or Change Group Number or Channel
Number

GROUP NUMBER SETTING CHANNEL NUMBER SETTING

(1) (2)

Keep press "-" for 5 "0" is flashing and choose any press " LOCK, TALK, or "1" is flashing and choose press " LOCK, TALK, or
seconds number from 0 to 19 GROUP any one of button any number from 0 GROUP any one button

(3)

(4)

to 19 . Group Number can not
same as the Channel Number. 5

once again.

(5)

Step 3 PUT THE UNIT IN DIFFERENT ROOM/PLACE

You can place the Channel 1 unit in Reception
Channel 2 unit place in General Manger Room
Channel 3 unit place in Financial Room
Channel 4 place in Store … etc.

Cautions :

1) The setting method of Samcom 20 channel wireless intercom is differ from Samcom 10
channel wireless intercom. but number 0 to 9 is same frequency. so they can be used in
communication if channel number is not over number 9

2) All of the Group Number must set to same number, otherwise Group function is not effective.

3) There are three Switch Position " A ,B,C ",the default position is on “A”; if you found inference
from neighbor you can change switch to B or C, when changing,pls keep all units position be
the same.

4) Do not put the intercoms and other electronic appliances too close,better to keep 1 meter
distance to avoid any interference even when it is operating property.

FTAN20A OPERATION PROCEDURE

ONE TO ONE TALKING

1) If you are in Channel 1 (Reception) want to talk with Channel 2 (GM Room) press key

"2" meanwhile the LCD display " Selective call 2"

6