Samurai Industrial Floor Stripper Operator's Manual

Industrial Floor Stripper Operator’s Manual

DO NOT operate this equipment until you have read and understood all the enclosed Operator’s Manual.

READ ALL the sections in this manual PRIOR to attempting to service, maintain or operate this equipment.

Warranty Statement

The SAMURAI Industrial Floor Stripper, is guaranteed to be free from any manufacturer’s defects in material and

workmanship for a period of six (6) months from the date of purchase. This warranty is exclusive of any normal wear and tear and/or consumable parts, such as, but not limited to, rubber bushings and blades. All normal wear and tear and/or consumable parts are protected from manufacturer’s defects in material and workmanship for a period of

thirty (30) days from the date of purchase.

Warranty Summary Protection

1. SAMURAI Industrial Floor Stripper 6 months parts and labour

2. SAMURAI normal wear and tear parts or consumable parts

To make a warranty claim within this time period, please contact the Service Manager at your local authorized

service centre, who will advise the validity and claim procedure. Once the claim has been accepted, the unit and/or parts should be shipped to the speciﬁ ed Authorized Service Centre at the customer’s expense. Be sure to securely pack the unit and parts in a strong container. Damage in transit is not covered by this warranty. All approved repairs under this warranty will be returned free of charge.

Warranties expressed in this document are void if repairs are attempted by anyone other than an Authorized Service Centre or if the unit has been modiﬁ ed from original factory design in any way. This warranty is expressly conditional upon the customer’s compliance with all precautions and instructions contained in this manual and excludes any claims made as a result of abuse, neglect, accident, normal wear and tear and misuse. This warranty is nontransferable.

30 days parts and labour

Our liability under warranty is limited to the repair of the product and/or replacement of parts and is given to the purchaser in lieu of all other remedies including incidental and consequential charges. There are no expressed warranties other than those speciﬁ ed herein.

Technical Support Hotline

c/o Technical Service

Uniquip Canada Inc.

SAMURAI North American Authorized Dealer

www.uniquip.ca

English Service

T : 1-888-332-4012 F : 1-866-567-0956

French Service

T : 1-800-332-4012 F : 1-866-825-2221

Warranty Registration

Congratulations for purchasing the SAMURAI Industrial Floor Stripper to meet all your tough jobsite needs! Please ﬁ le your original bill of purchase for this unit in a safe place. For warranty service of the SAMURAI you will need to provide a copy of this document to conﬁ rm your warranty status.

Product registration is a key step toward enjoying your new product! While registration is not necessary to enjoy our manufacturer’s warranty, there are many beneﬁ ts to participating in this program. Registration helps to facilitate warranty service, and notify you of any updates, changes, and service advisories on your product. Complete this Warranty Registration Card and mail it to the address on the back of this card or fax it to:

SAMURAI Warranty Programme

c/o Technical Service

Uniquip Canada Inc.

North American Authorized Dealer

P: 1-888-332-4012 F: 1-866-825-2221

Warranty Registration Information

A.Ownership Information

Owner’s Name: Company Name: Company Address:

Company Telephone: Company Fax:

Company E-Mail: Company Website:

B.Machine Information

Machine Make: Machine Model # Machine Serial # Date of Purchase:

C.Product Information Update

Can we contact you with any product-related news? Who should we contact? Contact Telephone: Contact Fax: Contact E-Mail:

What is the preferred contact method?

Fold along dotted line

SAMURAI Warranty Programme

c/o Uniquip Canada Inc.

North American Authorized Dealer

4101 boul.Industriel

Laval QC H7L 6G9

ATTN: TECHNICAL SERVICE

Place

Stamp

Here

Fold along dotted line

Contents

Pre-Operation Note 1 Safety Precautions 2 Guide to Parts Breakdown 4 Parts Breakdown 5 Information on Safety Decals 8 Contents List 9 Pre-Operating Procedures 9 Operating Procedures 10

A. Installing the blades and support mounts for the SAMURAI 10

A. Attaching the 5-3/8” blade 11 B. Attaching the 4” blade 11 C. Attaching the 9” blade 11

B. General principles in using the SAMURAI ﬂ oor stripper 13 C. Using the SAMURAI on stairs and other difﬁ cult to maneuver areas 14 D. Using the SAMURAI with the handle extension 14

Storing the SAMURAI 15 Maintenance Procedures 16

A. Inspection Schedule 17 B. General Service Procedures 17

1.Changing the bushings for the SAMURAI Floor Stripper 17 A. Disassembling the SAMURAI Floor Stripper 17 B. Changing the bearing SA-49 and rubber bearing cup SA-50 18 C. Replacing all the bushings, washers and bolts 19

2. Changing Motor Brushes 20

3. Changing Nylon Wheels 20

DO NOT operate this equipment until you have read and understood all the enclosed Operator’s Manual.

READ ALL the sections in this manual PRIOR to attempting to service, maintain or operate this equipment.

Pre-Operation Note

Thank you for your purchase of the SAMURAI Industrial Floor Stripper. This ﬂ oor stripper has been designed and manufactured to our highest quality demands for durability and performance.

We are committed to offering durable products and quality after-market service. The SAMURAI Industrial Floor Stripper is warranted to be free from manufacturer’s defects in material and workmanship for a period of six (6) months from the date of purchase. This warranty will be void if the machine has not been operated and maintained in the manner prescribed in this Operator’s Manual. Any machine malfunctions, and/or warranty claims that arise from the misinterpretation or the misunderstanding of the instructions and cautions discussed in this booklet will not be eligible for warranty protection.

In order for the ﬂ oor stripper to perform at its optimum capabilities, the operator must read this manual thoroughly before using this unit. This Operator’s Manual contains important product operation procedures, safety precautions, maintenance and troubleshooting tips as well as other advisories. Please keep this manual nearby at all times when operating the machine as a reference should any questions arise. If the machine is sold or transferred to another user, please ensure that this manual accompanies it.

The SAMURAI Floor Stripper is designed to remove existing laminate, vinyl and parquet ﬂ ooring. NOT RECOMMENDED FOR USE WITH CERAMICS. The machine should not be used for any other purpose than that stated above. The inappropriate use of any machine can cause serious damage and/or bodily harm to the environment and operator. It is imperative that the operator of this equipment be responsible for the operational environment of the ﬂ oor stripper. Please be prepared and well-informed for all speciﬁ c requirements precautions and work hazards that may and/or do exist at the jobsite.

Powered by a 1/2 hp, 5A induction electric motor, the SAMURAI is an industrial-use unit designed to make ﬂ oor stripping fast and easy. The SAMURAI has many features which are designed to improve your working experience. It comes with a complete set of accessories, including 3 different kinds of blades and their support mounts to help you tackle each type of ﬂ ooring with the right tool! The nut driver included is a handy tool to help you change blades and

perform maintenance quickly and safely. The removable extension handle maximizes comfort and ease of use of the ﬂ oor stripper for both ﬂ oors and stairways.

In order for you to enjoy the most out of your new ﬂ oor stripper, always keep safety as a priority. Inspect your

jobsite for any debris such as chipped tiles, glass, wiring, string or any other items that can become hazardous during work. Ensure that there are no electrical hazards, such as the presence of water, hazardous and ﬂ ammable substances. Make sure that the main power switch, located on the main unit, is switched OFF when there is no operator present. The jobsite environment, ﬂ oor conditions, job speciﬁ cations and operator experience will all be factors that must be considered to select the proper tool for the job. Failure to maintain the ﬂ oor stripper in a proper manner will lead to decreased productivity of the tool and hazards to the operator and bystanders. Do not use the machine if it has been modiﬁ ed or improperly maintained.

All jobsites are different. Please ensure that when using the SAMURAI Floor Stripper, all local bylaws and codes are followed. All operators and mechanics of this machine should be trained in general machine use and safety.

Every care and effort has been made to ascertain the accuracy and completeness of procedures described in this document to ensure your enjoyment and satisfaction. If you have any questions or concerns, please contact the Service Department at your authorized dealer.

Pre-Operation Notes

Safety Precautions

1. READ AND UNDERSTAND OPERATOR’S MANUAL PRIOR TO USE OF FLOOR STRIPPER.

2.Before operating ﬂ oor stripper, ensure that it is structurally and mechanically safe by checking the following:

a. Is the motor functioning within acceptable tolerances? b. Are the bushings for the enclosure and vibrating plate showing excessive wear and tear or uneven wear patterns? c. Are all the electrical cords and strain reliefs in good condition, with no evidence of rips, tears, cut insulation or bare wire showing?

If any of the above checks fail, please take necessary steps to maintain or repair the unit

3. Before using the ﬂ oor stripper on proposed jobsite, perform the following environmental checks:

a. Inspect the entire work area for unexpected hazards, such as gas and water pipes, electrical wiring or

cabling, under-ﬂ oor heating systems, damp areas or leakages. b. Clean work area of any litter or debris, such as wire, boards, rocks, or any other potential hazards. c. Verify that the machine will not used in an area of standing water, or that its power cord will be routed through such conditions.

d. Electrical power is supplied from a grounded and safe source, and that the source is of the same voltage to that speciﬁ ed on the machine.

before operating it in any environment.

Call your local utility company so that they can locate and mark these lines for you. Any cut elec-

4. Before using the ﬂ oor stripper on proposed jobsite, make sure that the operator is thoroughly familiar

with the machine and its components (see “Machine Overview”).

5. When operating the ﬂ oor stripper, follow these guidelines for operator’s personal safety:

a. Always wear proper safety clothing and equipment for the job. These can and should include eye and

ear protection, protective helmets, gloves, dust mask and any other items that are appropriate for the job and jobsite requirements

b. Never wear any jewelry, neck ties, or other loose or hanging items that can be caught on any part of

the machine c. Tie back or remove any loose hair, clothing and any other potential hazards and obstructions

d. Keep all hands, loose clothing, hair, jewelry and all other personal parts and belongings away from

moving parts of the machine. e. The last operator may have been negligent and his possible oversight could cause you death or serious

injury. Inspect machine before each use.

i. Verify that all enclosures and blades are whole and undamaged (ie.: no cracks) and will operate properly and perform its intended functions. ii. Verify that the moving parts are properly aligned and installed

f. Always use the proper size grounded outdoor use extension cord, conforming to your local electrical

codes and ordinances. Minimum acceptable gauge is 14 AWG. g. NEVER allow machines to run unattended. ALWAYS disconnect and store the machine

away if operator is not available.

h. The electrical motor will heat up when machine is in use. Machine must be allowed to cool before

touching it or attempting to perform any maintenance! i. Always allow blade and the motor to completely stop before attempting service or changing blades.

trical cable or gas line can result in injury or fatality.

Safety Precautions cont’d ...

6. For the safety of others and that of the operator, observe the following precautions:

a. Keep observers and bystanders away from the ﬂ oor stripper and its immediate working environment

(i.e.: the room or staircase that is being stripped etc.) while the machine is in use.

b. Before using the ﬂ oor stripper, power on the ﬂ oor stripper and observe if there is any unusual wobbling

or vibrations that indicate poorly installed blades or bushings that may require replacement. DO NOT USE IF MACHINE SHOWS SIGNS OF ABUSE OR POOR MAINTENANCE.

c. Stop operations or if anyone or anything (i.e.: humans, animals, debris etc.) approaches from any

direction while the machine is in operation.

d. Stop work and turn off the ﬂ oor stripper if it hits any debris that jams the machine or causes it to

labour unnecessarily. Inspect the ﬂ oor stripper and surrounding environment for any possible causes.

e. If the machine is jammed, turn the unit off using the main switch and disconnect the ﬂ oor stripper

from its power source before attempting to clear any jams in the unit.

f. Stop all work, turn off ﬂ oor stripper, unplug power cord(s) and ensure that motor is turned off and

cooled before performing any diagnostics or repairs. g. VIBRATIING FLOOR STRIPPER BLADES CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT ATTEMPT TO PERFORM ANY REPAIRS, SERVICE, OR DIAGNOSTICS OR TO TRANSPORT OR MOVE THE UNIT

UNTIL THE BLADE AND MOTOR HAVE BOTH COME TO A COMPLETE STOP. FAILURE TO DO SO MAY

RESULT IN SEVERE INJURY OR DEATH. h. Never leave machine unattended i. DO NOT, under any circumstances, operate machine if any of the following conditions are applicable:

i. Any impairment (i.e.: medical conditions, medicinal side-effects, alcohol, drugs etc.) of the

operator. ii. The operator has not read or understood the operator’s manual for this machine. iii. The operator does not clearly understand the operations of the machine. iv. The machine is in need of repair v. The operator is inappropriately attired to operate the machine.

7. Due to the nature of the machine and the tasks that it is designed to perform, consider the following cautionary recommendations:

a. The machine is designed to operate at optimum efﬁ ciency. DO NOT FORCE THE MACHINE TO

FUNCTION FASTER THAN THE RATE AT WHICH IT HAS BEEN SET.

b. ALWAYS guard against electrical shock. DO NOT come into contact with grounded surfaces, such as

pipes, radiators, refrigerators etc. c. ALWAYS wear protective eyewear and gloves when using the SAMURAI Floor Stripper. Removing ﬂ ooring materials creates a dusty environment in which the operator should always be protected.

SAVE THESE INSTRUCTIONS!!

Guide to Parts Breakdown

Regular maintenance and parts replacement are important steps to extending the life of your equipment and enjoying its optimum performance. When performing or conducting any maintenance or repairs, always check that your working surroundings are safe and well-ventilated and that the technician is familiar and comfortable with all aspects of the machine and required procedures.

This guide aims to serve as a representational guide to the SAMURAI. Any other uses or application beyond the scope of this document are strictly prohibited. While every attempt has been made to maintain its accuracy, SAMURAI reserves the right to update and modify the equipment without prior notiﬁ cation. Prior to undertaking to perform any maintenance or repair procedures, please contact our Technical Support Hotline for clariﬁ cation and to acquire appropriate parts.

To order spare parts, please provide the following information:

1. Machine Make

2. Model Number

3. Machine Serial Number

4. Quantity Required of Each Part

5. Part Numbers

6. Part Descriptions.

All SAMURAI parts are guaranteed by a thirty (30) day warranty against any manufacturer’s defects in workmanship and material. Consult page A in the Operator’s Manual for further details on our Warranty Policy.

Technical Support Hotline

c/o Technical Service

Uniquip Canada Inc.

SAMURAI North American Authorized Dealer

www.uniquip.ca

English Service

T : 1-888-332-4012 F : 1-866-567-0956

French Service

T : 1-800-332-4012 F : 1-866-825-2221

+ 19 hidden pages

Samurai Industrial Floor Stripper Operator's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual