How it Works
Samsung Electro Mechanics
Loading...
SCF V01
User Manual
91 pgs5.51 Mb0

Samsung Electro Mechanics SCF V01 User Manual

Download
Samsung Electro
1C CDMA
the
A
V01
Proprietary and Confidential
general performance and specifications of
A
Mechanics. All rights reserved
The names of actual companies and products mentioned
herein may be the trademarks of their respective owners.
be reproduced, stored in a
retrieval system, or transmitted in any form
means without the express written consent of Samsung
change without notice
SCF-V01
SCF-
User Manual
VIA Telecom CBP7.
REV 0.1
Samsung Electro-Mechanics
2012-06-18
Summary
This datasheet presents
1x Rel.0 and 1X EV-DO Rev.
Solution
SCF-V01 CDMA2000 A
Module.
© 2012 Samsung Electro-
No part of this document may
Electro-Mechanics.
This document is subject to
REV 0.1
-Mechanics
or by any
.
1/16
Samsung Electro
DESCRIPTION
ESCRIPTION
................................
................................
................................
PIN ASSIGNMENTS
................................
................................
................................
ASSIGNMENTS AND DESC
................................
................................
ELECTRICAL CHARACTER
................................
HARACTERISTI
................................
................................
RF
................................
................................
................................
................................
................................
................................
V01
Proprietary and Confidential
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
Table of Contents
SCF-
User Manual
1 GENERAL
1.1 F
1.2 F
1.3 A
1.4 B
UNCTIONAL
EATURES
PPLICATIONS
LOCK DIAGRAM
D
2 DIMENSION AND
2.1 M
ECHANICAL DIMENSION
2.2 A
NTENNA CONNECTION
2.3 G
ROUND CONNECTION
3 PIN
3.1 P
4
IN ASSIGNMENTS
3.2 P
IN DESCRIPTION
4.1 DC C
4.2 E
4.3 P
HARACTERISTICS
NVIRONMENTAL
OWER CONSUMPTION
C
5 RF SPECIFICATIONS
................................................................
................................................................
................................
................................
................................
................................
................................
................................
................................
RIPTIONS ................................
................................
................................
ISTICS ................................
CS
................................
................................
................................
................................
.... 3
..... 3
.......................... 3
..................... 3
.................. 4
................ 5
........ 5
.......... 6
........... 6
........... 7
................ 7
................ 8
...................... 10
......... 10
......................... 10
......... 11
........ 12
5.1 B
ASIC PERFORMANCE OF
6 LABEL INFORMATION
6.1 M
ODULE LABEL
7 SAFETY INFORMATION
7.1 C
7.2 C
ERTIFICATION
AUTION
REVISION HISTORY
SPECIFICATIONS
................................
................................
................................
................................
................................
................................
................................
.............. 12
...... 14
.................. 14
.... 15
................. 15
......................... 15
................ 16
REV 0.1
-Mechanics
2/16
Samsung Electro
Description
Functional Description
module for
Management and software, which
It supports Cell and PCS bands.
Dual band cellular and PCS voice and data
CDMA2000 A 1x Rel.0
Diversity reception
Support Cell and PCS bands
U.FL Antenna port : Main, AUX
power consumption
.0
USB2.0 full speed USB driver
All CDMA M2M devices (Energy, Industrial & Infrastructure, Security, etc.)
CDMA equipment laptop PC
CDMA portable device (Tablet, MID, PMP, etc.)
SCF-
V01
Proprietary and Confidential
1X EV/DO Rev
provides all the RF, Processing, Memory, Power
or CBP7.x
User Manual
1 General
1.1
SCF-V01 is the cellular
embedded and wireless M2M
1.2 Features
Variant module :
Optional GPS and RX
GPS (optional)
3
Low
either the CDMA2000 A 1x Rel.0 or
applications. It
is based on the Via Telecom CBP6.x
or 1X EV/DO Rev. A
, & GPS (50 Ohm)
. A at
solution.
Dimension: 50.95 x 30
RoHS compliant
Operating temperature
1.3 Applications
Desktop CDMA CPE
mm / Hmax : 4.75 mm
range: -20 to 60℃
REV 0.1
-Mechanics
3/16
Samsung Electro
block diagram highlights the major func
Figure
V01
Proprietary and Confidential
tional blocks and interfaces.
1.4 Block Diagram
SCF-
User Manual
The following SCF-V01
1-1. SCF-V01 Hardware Block Diagram
REV 0.1
-Mechanics
4/16
Samsung Electro
Dimension and
Mechanical Dimension
Standard PCI Express
Mini Card)
Size : W x L x H (50.95 x 30.0 x 4.75mm)
-
SCF-
V01
Proprietary and Confidential
Mini Card Electromechanical Speci
n (Top View)
User Manual
2
2.1
Form factor :
(Full-
Weight : 9.8g
Pin Assignments
®
with 1.0mm PCB
fication
Figure 2
REV 0.1
1. SCF-V01 Mechanical Dimensio
-Mechanics
5/16
Samsung Electro
Antenna Connection
ain ANT,
-
ttaching an antenna to the
Use a Hirose U.FL connector (Part No. : U.FL
antenna to a connection point on the SCF
connections between the SCF
mize RF cable losses
Connection
V01 to system ground :
Connect to system ground for preventing noise leakage.
Connect with host connector, two mounting holes, and
V01
Proprietary and Confidential
Antenna Connector Mechanical Dimension
-
Ω.
the antenna to less than 0.5 dB.
m
-
Ω.
2.2
SCF-
User Manual
U.FL connector for the M
Figure 2
A
Match coaxial
Diversity ANT, and GPS ANT
2.
SCF-V01 :
-R-SMT, CL No. : 331
-V01.
-V01 and the antenna to 50
0471-0-10) to attach an
Mini
2.3 Ground
Connecting the SCF-
between the SCF-V01 and
PCI express®
ini card connector.
REV 0.1
-Mechanics
6/16
Samsung Electro
Assignments and
SCF
SCF-
V01
Proprietary and Confidential
User Manual
3 Pin
3.1 Pin Assignments
Pin# Mini Card Standard
51 Reserved 49 Reserved 47 Reserved 45 Reserved 43 GND 41 +3.3Vaux 39 +3.3Vaux 37 GND 35 GND 33 PETp0 31 PETn0 29 GND 27 GND 25 PERp0 23 PERn0 21 GND 19 UIM_C4 17 UIM_C8
15 GND 13 REFCLK+ 11 REFCLK-
9 GND 7 CLKREQ# 5 COEX2 3 COEX1 1 WAKE#
Descriptions
-V01 Pin name Pin# Mini Card Standard
(JTAG_RST_N) 52 +3.3Vaux
(JTAG_TDI) 50 GND (JTAG_TDO) 48 +1.5V (JTAG_TMS) 46 LED_WPAN#
GND 44 LED_WLAN# +3.3V +3.3V
GND 38 USB_D+
GND 36 USB_D-
(JTAG_CLK) 34 GND
(JTAG_RTCK) 32 SMB_DATA
GND 30 SMB_CLK
GND 28 +1.5V
(RXD0) 26 GND (TXD0) 24 +3.3Vaux
GND 22 PERST#
N.C 20 W_DISABLE# N.C 18 GND
Mechanical Key
GND 16 UIM_VPP
N.C 14 UIM_RESET N.C 12 UIM_CLK
GND 10 UIM_DATA
N.C 8 UIM_PWR N.C 6 1.5V N.C 4 GND N.C 2 3.3Vaux
Table 3-1. Pin Assignments
42 LED_WWAN# 40 GND
SCF-V01 Pin name
+3.3V
GND
N.C N.C N.C
LED_WWAN#
GND
USB_D+
USB_D-
GND
N.C N.C N.C
GND
+3.3V
RESET_N
W_DISABLE#
GND
N.C
UIM_RESET_N
UIM_CLK
UIM_IO
VDD_UIM
N.C
GND
+3.3V
REV 0.1
-Mechanics
7/16
Samsung Electro
V01
Proprietary and Confidential
IC Pin
Domain
t
JTAG Return Clock
data out
data in
Inverted USB transceiver data
inverted USB transceiver data
output
, Active low signal
Status indicator via LED device, Active low signal
UIM power output
t
3.2 Pin Description
Pin# Signal Name Type
JTAG Interface
33 JTAG_CLK
47 JTAG_TDO
45 JTAG_TMS
49 JTAG_TDI
51 JTAG_RST_N 31 JTAG_RTCK
UART Interface
23 TXD0
25 RXD0
USB Interface
38 USB_D-
36 USB_D+
UIM Interface
10 UIM_IO
12 UIM_CLK
14 UIM_RST_N
GPIOs and Miscellaneous
22 PERST# I 20 W_DISABLE#
42 LED_WWAN# O
Power Supplies
41 +3.3V I
39 +3.3V I 52 +3.3V I
24 +3.3V I
8 VDD_UIM 2 +3.3V
Ground
43 GND -
37 GND -
35 GND -
29 GND -
27 GND -
21 GND -
15 GND -
9 GND -
50 GND -
40 GND -
I
O
I
I I
O
O
I
IO
IO
IO
O
O
I
O
I
SCF-
Connection to
CP_TCK (N.C) JTAG Clock
CP_TDO (N.C) Data Out
CP_TMS (N.C) Mode Selec
CP_TDI (N.C) Data In CP_TRST_N (N.C) JTAG Reset CP_RTCK (N.C)
CP_UART0_OUT (N.C) UART0
CP_UART0_IN (N.C) UART0
USB_DMN
USB_DPS Non-
UIM_IO
UIM_CLK
UIM_RSTN
PM Reset Functional Reset
GPIO[01] RF Disable GPIO[06]
3.3V Source
Power
-
-
-
-
-
Description
UIM data input-
UIM clock signal
UIM reset signal
3.3V Source
3.3V Source
3.3V Source
3.3V Source
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
User Manual
REV 0.1
-Mechanics
8/16
Samsung Electro
directional
SCF-
V01
Proprietary and Confidential
User Manual
34 GND -
26 GND -
18 GND -
4 GND -
Type: I=Input, O=Output, I/O=Bi-
-
-
-
-
Table 3-2. Pin Descriptions
Ground
Ground
Ground
Ground
REV 0.1
-Mechanics
9/16
Samsung Electro
Electrical Characteristics
DC Characteristics
Parameter
Main input supply from battery to switcher
Table
Parameter
supply from battery to switcher
Table
vironmental Characteristics
Parameter
static discharge voltage
Operating temperature
perating temperature
Storage temperature
Extended operating temperature range is not fully 3GPP2 CDMA specification compliant.
Table
SCF-
V01
Proprietary and Confidential
Typ.
Typ.
3
Min
0
30
0
User Manual
4
4.1
Symbol
+3.3V
Symbol
+3.3 Main input
4.2 En
Symbol
Min
-0.5 -
4-1. Absolute Maximum Ratings
Min
3.0 3.
4-2. Recommended Operating Conditions
Conditions
Max Unit
+4.8 V
Max Unit
3.6 V
. Max. Unit
ESD Electro-
To
Te Extended o
Ts
※
HBM
-2
-
-4
4-3. Environmental Characteristics
Class 1C
+60 °C
+85 °C
+125 °C
REV 0.1
-Mechanics
10/16
Samsung Electro
Power Consumption
V01
Proprietary and Confidential
@ Room Temp
Cell Power
Tx Power 23.5
Cell Power
Tx Power 23.5dBm
Cell Power
Tx Power 23.5dBm
Cell Power
Tx Power 23.5dBm
4.3
SCF-
User Manual
Format RF Band
PCS
1x_RTT
Cellular
PCS
EVDO
[Rev 0]
Cellular
Mode
Idle Mode Typ 160mA
Min Tx Power Typ 250mA
Tx Max Power
Idle Mode Typ 160mA
Min Tx Power Typ 220mA
Tx Max Power
Idle Mode Typ 200mA
Min Tx Power Typ 340mA
Tx Max Power
Idle Mode Typ 200mA
Min Tx Power Typ 330mA
Tx Max Power
Typ 670mA
Max 750mA
Typ 610mA
Max 650mA
Typ 900mA
Max 940mA
Typ 800mA
Max 850mA
Current
@ 3.3V
Condition
-25dBm
dBm
-25dBm
-25dBm
-25dBm
REV 0.1
-Mechanics
11/16
Samsung Electro
RF Specifications
All measurements are made under
Basic performance of RF
Transmitter Specif
Operating Frequency
Conversion Method
Oscillation Method
RF Output Power
Frequency Stability
Receiver Specification
Operating Frequency
Conversion Method
Oscillation Method
Receiver Sensitivity
SCF-
V01
Proprietary and Confidential
temperature conditions
Value
824MHz ~ 849MHz (Cellular Band)
MHz~1910MHz(PCS Band)
OQPSK/H
IF (intermediate frequency)
IF radio technology
VCTCXO & PLL Synthesizer
Maximum 0.2W
Minimum 10nW (
300Hz
Value
869MHz ~ 894MHz (Cellular Band)
MHz~1990MHz
/HPSK
IF (intermediate frequency) & low
VCTCXO & PLL Synthesizer
FER 0.5%
FER 0.5% for EVDO
User Manual
5
5.1
Frequency : Band Class0 :
Band Class1 :
Impendence : 50ohm
VSWR : < 3
Modulation
nominal supply voltage and room
Specifications
TX:824MHz-849MHz; RX:869MHz-894MHz
TX:1850MHz-1910MHz; RX:1930MHz-1990MHz
ication
GCT`s intrinsic zero-
1850
& low-
.
PSK
+/-
Table 5-1. Transmitter Specifications
Modulation
Table 5-2. Receiver Specifications
1930
OQPSK
Zero-
-104dBm @
-105.5dBm @
-50dBm)
（
PCS Band）
for 1X
-IF
REV 0.1
-Mechanics
12/16
Samsung Electro
Typ
5
5
Table
SCF-
V01
Proprietary and Confidential
Test Condition
Cellular Band(824.7MHz,836.52MHz ,
PCS Band(1851.25MHz , 1880MHz ,
Cellular Band(824.7MHz,836.52MHz ,
PCS Band(1851.25MHz , 1880MHz ,
Cellular Band(824.7MHz,836.52MHz ,
PCS Band(1851.25MHz , 1880MHz ,
Cellular Band(824.7MHz,836.52MHz ,
PCS Band(1851.25MHz , 1880MHz ,
Cellular Band(824.7MHz,836.52MHz ,
PCS Band(1851.25MHz , 1880MHz ,
Cellular Band(869.7MHz,881.52MHz ,
105dBm , 95% Confidence
PCS Band(1931.25MHz , 1960MHz ,
105dBm , 95% Confidence
User Manual
ITEM
Tx Max
Power
Tx Min Power
Rho
Frequency
Error
Time Error -1
LCL
23.0 23.
23.0 23.
0.944
0.944
-300
-150
Spec
UCL Unit
24.0 dBm
24.0 dBm
-50 dBm
-50 dBm
1
1
300 Hz
150 Hz
1 us
848.41MHz) Cal Target : 23.7dBm
1908.75MHz) Cal Target : 23.7dBm
848.41MHz)
1908.75MHz)
848.41MHz)
1908.75MHz)
848.41MHz)
1908.75MHz)
848.41MHz)
1908.75MHz)
Rx Sensitivity
(Primary /
Secondary)
0.5 %
0.5 %
893.31MHz) Cell Power : -
1988.75MHz) Cell Power : -
5-3. RF Conduction Specifications
REV 0.1
-Mechanics
13/16
Samsung Electro
Information
The Label contains Model Name, Product Code, FCC ID, MEID and Serial Number.
Figure
: CEMF10V01D0101
Id
: Main Antenna connection
: GPS Antenna connection
Antenna connection
S/N(Serial Number)
Q
Custom Model
CEMF10V01D0101
Table
SCF-
V01
Proprietary and Confidential
User Manual
6 Label
6.1 Module Label
[Information]
① Model : SCF-V01
② Product Code
③ FCC ID : E2XSCF-V01
6-1. Label Information
④ MEID : Mobile Equipment
⑤ S/N : Serial Number
⑥
MAIN
⑦ GPS
⑧ AUX : Diversity
6.1.1
Ex)
S Q G B 000001
S
Company
S: Samsung
Q :
entifier
G B
6-1. Serial Number Information
Year F:2011 G:2012
Month
1~9:Jan~SEP
A:OCT, B:Nov,
C:Dec
000001
000001~FFFFFF
Serial No(Hex)
REV 0.1
-Mechanics
14/16
Samsung Electro
Safety Information
Warning: Exposure to Radio Frequency Radiation The radiated
output power of this device is far below the FCC radio frequency
exposure limits. Nevertheless, the device should be used in such a
manner that the potential for human co
is minimized. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the antenna
should not be less than 20 cm during normal operation. The gain of
the antenna for
must not exceed
Can be found under the Display Grant section of
FCC Compliance Information
is device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received.
Including interference that may cause u
Modifications not expressly approved by the party responsible for compliance could void the user
authority to operate the equipment.
SCF-
V01
Proprietary and Confidential
ntact during normal operation
dBi
www.fcc.gov/oet/ea/fccid
User Manual
7
7.1 Certification
FCC ID : E2XSCF-V01
Cellular band must not exceed 2
2 dBi.
and PCS band
after searching on
FCC ID: E2XSCF-V01
Th
7.2 Caution
ndesired operation.
’s
REV 0.1
-Mechanics
15/16
Samsung Electro
Descriptions
0.0 2012-02-10 Initial Release
0.1 2012
-06-18
Add Label Information, Add Safety Information
V01
Proprietary and Confidential
Revision History
SCF-
User Manual
Revision Date
REV 0.1
-Mechanics
16/16
REV 0.1
Samsung Electro-Mechanics Proprietary and Confidential
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
ˍ Reorient or relocate the receiving antenna. ˍ Increase the separation between the equipment and receiver. ˍ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ˍ Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
d your body.
For label requirement when transmitter module is installed in a host,
)RUODEHOUHTXLUHPHQWZKHQWUDQVPLWWHUPRGXOHLVLQVWDOOHGLQDKRVWWKHKRVWVKDOOKDYHDQDGGLWLRQDOSHUPDQHQWODEHOUHIHUULQJWRWKHHQFORVHGPRGXOH³&RQWDLQV7UDQVPLWWHU0RGXOH)&&,'%(-7:)0%'´)RUODEHOUHTXLUHPHQWZKHQWUDQVPLWWHUPRGXOHLVLQVWDOOHGLQDKRVWWKHKRVWVKDOOKDYHDQDGGLWLRQDOSHUPDQHQWODEHOUHIHUULQJWRWKHHQFORVHGPRGXOH³&RQWDLQV7UDQVPLWWHU0RGXOH)&&,'%(-7:)0%'´T7KLVUDGLRFDQQRWEHLQVWDOOHGLQKRVWZKHUHFRORFDWHGRURSHUDWLQJLQFRQMXQFWLRQZLWKDQ\RWKHUDQWHQQDRUWUDQVPLWWHUhis transmitter must not be collocated or operating in conjunction with any other antenna or transmitter unless authorized to do so by the FCC.
G
the host shall have an additional permanent label referring to the enclosed module
G
“Contains Transmitter Module FCC ID: lY
SCF-V01
8/8
SCF-V01 ETS(Engineer Test Software) User Manual
REV 0
Steve Heo, Software Application Engineer
Software Part WS Development Team Samsung Electro-Mechanics
2012-06-28
Background & Summary
This document describes how to use ETS.
© 2012 Samsung Electro-Mechanics. All rights reserved
The names of actual companies and products mentioned herein may be the trademarks of their respective owners.
This document is subject to change without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without the express written consent of Samsung Electro-Mechanics.
Samsung Electro-Mechanics Co., Ltd. Proprietary
Samsung Electro-Mechanics Co., Ltd. Proprietary
Table of Contents
REV 0
1 INTRODUCTION ................................................................................................................. 3
1.1 A
1.2 L
CRONYMS
IST OF TERMS
....................................................................................................................... 3
.................................................................................................................. 3
2 SETUP AND QUICK START .................................................................................................. 4
2.1 S
YSTEM REQUIREMENTS
2.2 I
NSTALLING AND REMOVING
2.3 R
UNNING
2.4 H
OW TO EXIT
2.5 O
2.6 ETS D
2.7 ETS O
ETS
PENING AND SAVING CONFIGURATION FILES
EFINES PTIONS
FOR THE FIRST TIME
.................................................................................................................... 7
.................................................................................................................. 10
.................................................................................................................. 11
....................................................................................................... 4
................................................................................................... 5
......................................................................................... 7
............................................................................. 7
3 IDLE MODE ....................................................................................................................... 12
3.1 RSSI
3.2 O
3.3 R
3.4 TX PWR D
3.5 HWD F
3.6 P
FOR
CDMA ............................................................................................................. 12
VERHEAD PAGING SPY
EGISTRATION MESSAGE SPY
ETECT MEASUREMENTS SPY
REQUENCY CHANNEL TRACE
ILOT STRENGTH SPY
...................................................................................................... 12
........................................................................................................ 15
............................................................................................... 13
.................................................................................... 13
........................................................................................ 14
4 IN-CALL MODE.................................................................................................................. 16
4.1 V
OICE CALL INITIATE
4.2 V
OICE CALL ANSWER
4.3 V
OICE CALL HANG UP
4.4 V
OICE CALL CONFIGURATION
4.5 R
ADIO CONTROL
......................................................................................................... 16
......................................................................................................... 17
........................................................................................................ 18
............................................................................................... 18
.............................................................................................................. 20
5 TEST/DEBUG CAPABILITY ................................................................................................ 21
5.1 B
ASICS
.......................................................................................................................... 21
5.2 T
EST MODES
5.3 RF I
NTERFACE AND CONTROL
................................................................................................................... 24
............................................................................................... 29
5.4 SMS ............................................................................................................................. 41
5.5 D
ATABASE UPLOAD/DOWNLOAD
5.6 S
OFTWARE OPERATION STATUS
5.7 CBP H
ARDWARE
............................................................................................................... 66
............................................................................................ 42
............................................................................................ 56
6 UTILITIES ......................................................................................................................... 67
6.1 V
IRTUAL
MMI ................................................................................................................. 67
6.2 S
CRIPT UTILITY
................................................................................................................ 67
REVISION HISTORY ................................................................................................................ 74
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page ii
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
1 Introduction
This document provides high-level functional descriptions of the CBP 5.X CDMA Baseband Processor
digital hardware subsystems.
1.1 Acronyms
ADC Analog-to-Digital Converter
AMPS Advanced Mobile Phone System
APB ARM Peripheral Bus
CBP5.X CDMA Baseband Processor version 4.1/5.0/5.1
CP Control Processor
DAI Digital Audio Interface
DAC Digital-to-Analog Converter
DSPM Digital Signal Processor - Modem
DSPV Digital Signal Processor – Voice
DUT Device Under Test
EBI External Bus Interface
ICE In-Circuit Emulator
MMI Man-Machine Interface
PCG Power Control Group
PLL Phase Locked Loop
PWM Pulse-Width Modulator
RTOS Real-Time Operating System
SAT Supervisory Audio Tones
SPI Serial Programming Interface
ST Signaling Tone
THRE Transmitter Holding Register Empty
UART Universal Asynchronous Receiver/Transmitter
UIM User Identity Module
WBD Wideband Data
1.2 List of Terms
Table 1 contains a list of terms and abbreviations used in this section.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 3
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Table 1 - External Interface Pin Attributes
Type Description
pu1
pd2 ldrv1 CMOS, low drive strength (1ma)
ldrv2 CMOS, low drive strength (2ma)
mdrv
hdrv CMOS, high drive strength (8ma)
_N Indicates an active low signal
z Tri-state
od Open-drain
vanlg Input or output with analog voltage levels
dvdd_c
dvss_c Digital VSS to core cells.
dvdd_r Digital VDD to pad ring (3V)
dvss_r Digital VSS to pad ring
avdd Analog VDD (3V)
avss Analog VSS
1
Internal pull-up resistors are non-linear elements; they have a resistance of about 80 K at
Internal pull-up
Internal pull-down
CMOS, medium drive strength (4ma)
Digital VDD to core cells (1.8V)
operating conditions of nominal process, 25o C and 3 V I/O supply voltage. They exhibit 140 K at
operating conditions of WC process, 125oC junction and 2.85 V I/O supply and 42 K at
conditions of BC process, 0o C and 3.15 V supply voltage.
2
Internal pull-down resistors: The same conditions apply as listed above for internal pull-up
resistors.
Table 2 - Reset Legend
Type Description
Z Tri-State H Tri-State with Pull-Up
L
1 CMOS High 0 CMOS Low
X Unknown
Tri-State with Pull-Down
2 Setup and Quick Start
2.1 System Requirements
The following are the minimum requirements for running ETS:
Operating System: Windows 2000/XP or later
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 4
Samsung Electro-Mechanics Co., Ltd. Proprietary
Memory: At least 128 MB of RAM
Processor: Pentium II or better
2.2 Installing and Removing
2.2.1 Installing ETS
REV 0
VIA Telecom delivers the installation program,
Telecom strongly recommends installing ETS in the default directory as the installing shell indicated.
The VIA Telecom software releases are typically numbered “rX.Y.Z” where:
X = Major Release Number
Y = Minor Release Number
Z = Patch to Minor Release
The VIA Telecom complete software package contains:
a. The VIA Telecom CP code, which executes on
the ARM7TDMI-S™ processor embedded in the CBP5.X chip.
b. An “.img” Image file, which contains code or code patches that will run on the DSPM and DSPV
embedded Oak processors.
c. The “ETS.exe” and “ETS_Config_x.exe” package, which installs ETS.
Example
Assume that the VIA Telecom software release is: r6.0.6.
1. The ETS installation program would be: <Customer Path>\ PCTools\ ets\ ETS_6.0.6.exe and
“ETS.exe”
, as part of the software release package. VIA
ETS_Config_0.14.2_vtui2_5x.
2. Run ETS_6.0.6.exe and ETS_Config_0.14.2_vtui2_5x . For this example, ETS is installed in
"C:\ Program Files\ VIA Telecom\ VTC-ETS\ ", ETS_Config is in “C:\ Program Files\ VIA
Telecom\ ETS_Config\ ".
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 5
Samsung Electro-Mechanics Co., Ltd. Proprietary
3. For other items which will meet in installing process, use default setting is fine. Since from now on,
all of CBP5.X reference software will use same ETS.exe, you NEED NOT pay additional attention to
associate version number between the software release and ETS.
REV 0
2.2.2 Removing ETS
Use the standard Windows method to remove (uninstall) software.
1. Go to the Control Panel and select Add or Remove Programs.
2. Select ETS and click the Add/Remove button. Follow the standard procedure for uninstalling
Windows-based software.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 6
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
2.3 Running ETS for the First Time
Continuing with the example in Section 2.21, start ETS by selecting:
Windows Desktop →ETS(Config 0.14.2_vtui2_5x_Selle_P1):
Now follow the steps in Section 2.5.1.
2.4 How to Exit
1. From the ETS menu, select File Exit
See Section 2.5.2 for details on how to save the ETS configuration when exiting.
→→→→
.
2.5 Opening and Saving Configuration Files
2.5.1 Opening Configuration Files
1. From the ETS menu, select File → Open...
2. Continuing with the
Example
of Section 2.2.1, in the Window below select the Path:
C:\ Program Files\ VIA Telecom\ ETS_Config\ 0.14.2_vtui2_5x_Selle_P1\ config\ cdma and
then select the file default.cfg
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 7
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 8
Samsung Electro-Mechanics Co., Ltd. Proprietary
3. After opening default.cfg you should see a screen, which looks similar to the picture below. This
screen has all the standard ETS sub-windows which are typically used at VIA Telecom.
REV 0
2.5.2 Saving Configuration Files
1. If you have used any special ETS commands during your present session which you’d like to use in a
future session then you can explicitly save the present configuration by using the ETS Main Menu
command:
File Save As→
2. Enter the name and path for your configuration file in the dialog box below, or you can choose to
overwrite the present configuration file (typically, “default.cfg”).
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 9
Samsung Electro-Mechanics Co., Ltd. Proprietary
2.6 ETS Defines
File Defines→
REV 0
ETS allows the user to configure the tool for various standard definitions:
Note:
1. This defines must be configured correct as the target HW you using. Else it will case some UN-expect
error. If you don’t sure which option you should select, call VIA application engineer for help.
2. After you changed the definition, should close and restart ETS to make the effort available.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 10
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
2.7 ETS Options
File Options→
There are some parameters you can modify, the value depend on the CP request. Special for Flash
Download Timeout (Sec), we recommend you adjust it longer than the total CP erase time (the lager
CP size is, the longer erase time is). 200s is the typically value VIA internal used.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 11
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
3 Idle Mode
3.1 RSSI for CDMA
CDMA: DSPM → Spy → RFC → DSPM Rfc RxTx
Usually this window is opened from loading the “default.cfg” configuration file.
Window Entries Definition
Print If checked, the window will be printed onto the main log as a trace:
15:17:28.8> ETS, Id=DSPM Spy, SpyId=DSPM Rfc RxTx, Sys Time=0xa248d231, Received Power (dBm)=-68.13, Receive PDM Value=0x0000, Rx Gain State=3, Transmit Power (dBm)=-150.00, Transmit PDM Value=0x0000, Tx Gain State=0,
Bitsel=-5, Gain=7, HwVal=0xfec7 Sys Time Recorded system time for reference purposes. Received Power (dBm) Received power from the BS interpreted by the MS. Receive PDM Value Received power from the BS interpreted by the MS in PDM. This area used for
superhet solution. Rx Gain State Gain state that the MS receiver is in. Transmit Power (dBm) Transmit power to the BS interpreted by the MS in dBm. Transmit PDM Value Transmit power to the BS interpreted by the MS in PDM. Tx Gain State Gain state that the MS transmitter is in. RxDAgc Value Received power from the BS interpreted by the MS, this area used for DCR solution.
3.2 Overhead Paging Spy
CP → SPY → PS → Call Proc → Engine → Eng_Layer2_TR → CP PE ENG_LAYER2_TR 13 13 (for
CDMA)
The spy is enabled automatically once the “default.cfg” is loaded. This spy displays all CDMA overhead
paging messages broadcast from the base station.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 12
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
3.3 Registration Message Spy
CP → SPY → PS → Call Proc → Engine → ENG_ACCESS_PROC_TR → CP
ENG_ACCESS_PROC_TR 1 40
The spy is enabled automatically once the “default.cfg” is loaded. This spy displays all messages from
mobile to the base station during idle mode, through access channel.
3.4 Tx PWR Detect Measurements Spy
CP → Spy → HWD → CP Tx Pwr Detect Measurements
This spy only works in the following conditions:
Tx Pwr Detect cal tables “Tx Pwr Detect” and “Tx Pwr Det Freq Adj” and “Det Temp Adj” are
populated.
Mobile is transmitting beyond the threshold that AUX ADC actually kicks in (typically +15dBm or
above)
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 13
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections Definition
Print If checked, the window will be printed onto the main log as a trace:
10:40:50.1> ETS, Id=CP Spy, SpyId=CP Tx Pwr Detect Measurements, Sys Time=0x823ee47e, Measured AUX ADC=0x04de, Tx Pwr (dBm)=-24.781250, Tx Pwr Freq Adj (dBm)=5.000000, Tx Pwr Temp Adj (dBm)=0.000000, Unadj
Tx Pwr (dBm)=19.781250 Sys Time Display system time for reference. Measured AUX ADC Reads AUX ADC value of Tx Pwr Detect. Tx Pwr (dBm) Displays mobile’s final transmitting power in dBm. Tx Pwr Freq Adj (dBm) Display corresponding Adj read from cal table. Tx Pwr Temp Adj (dBm) Display corresponding Adj read from cal table. Unadj Tx Pwr (dBm) Display the unadjusted Tx power transmitted.
3.5 HWD Frequency Channel Trace
CP → Trace → HWD → CP Freq Channel
This trace is enabled automatically once the “default.cfg” is loaded. This trace displays the channels that
the mobile searches in the Trace Log Window when the protocol stack is on:
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 14
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
3.6 Pilot Strength Spy
CP → Spy → L1D → CP Search Results Active
Usually this window is opened from loading the “default.cfg” configuration file. This spy display
information of Active PNs involved, candidate PNs that are possible for handoffs, and neighbor PNs that
are available for possible handoffs.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 15
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections
Print If checked, the window will be printed onto the main log as a trace:
15:36:10.1> ETS, Id=CP Spy, SpyId=CP Search Results Active, Sys Time=0xa249ad32, Num Act=0x01, Num Cand=0x00, Num Nghbr=0x17
, Stale.0=0, Pilot PN.0=54, Phase.0=3457, Strength.0=-4.4224 , Stale.1=1, Pilot PN.1=0, Phase.1=0, Strength.1=-1.#INF , Stale.2=1, Pilot PN.2=0, Phase.2=0, Strength.2=-1.#INF , Stale.3=1, Pilot PN.3=0, Phase.3=0, Strength.3=-1.#INF , Stale.4=1, Pilot PN.4=0, Phase.4=0, Strength.4=-1.#INF , Stale.5=1, Pilot PN.5=0, Phase.5=0, Strength.5=-1.#INF
, Stale.0=1, Pilot PN.0=0, Phase.0=0, Strength.0=-1.#INF , Stale.1=1, Pilot PN.1=0, Phase.1=0, Strength.1=-1.#INF , Stale.2=1, Pilot PN.2=0, Phase.2=0, Strength.2=-1.#INF , Stale.3=1, Pilot PN.3=0, Phase.3=0, Strength.3=-1.#INF ,
(etc. up to Stale39=…) Sys Time Display system time for reference. Num Act Number of PNs currently on the active list. Num Cand Number of PNs currently on the candidate list. Num Nghbr Number of PNs currently on the neighbor list. Stale “1” = such PN is actually available for communications to mobile. Pilot PN Display the PN number(s) of the pilot(s) that the mobile is aware of. Phase Display the phase of the pilot seen by the mobile. Strength Display the strength of the pilot seen by the mobile.
Definition
4 In-Call Mode
4.1 Voice Call Initiate
Utilities -> Virtual MMI Utility
To initiate a call, first click “Power” then dial any number and click “Send” Key on the Virt MMI.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 16
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
As an alternative to using the Virtual MMI, calls can be initiated using:
CP → PS → UI Command → CP Call Initiate
Window Selections Definition
Send Send to perform call initiate command. Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”. Otasp Check if it is an OTASP call. Otasp Mode If it is an OTASP call, entry OTASP mode. E911 Call Check if it is calling “E911”. Request Mode Service Option Choice a service option Privacy Mode Encoded Digit Mode Number Type Number Plan Number of Digits Digits
4.2 Voice Call Answer
Similar to section 4.1, there are two ways of achieving this: through Virtual MMI or CP command.
1. Using Virtual MMI, click “Send” when “Call Alert” is displayed.
2. Or use CP PS
→ →
UI Command CP Call →Answer and click “Send”
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 17
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
4.3 Voice Call Hang Up
Similar to section 4.1, there are two ways of achieving this: through Virtual MMI or CP command.
Using Virtual MMI, click “End” to terminate a call.
Or use CP PS
→ →
UI Command CP Call Hangup and click “Send”→
4.4 Voice Call Configuration
4.4.1 Voice Privacy Enable/Disable
CP → UI → CP Set Privacy Mode
CP → PS → Voice Privacy → CP Voice Privacy Enable (or Disable)
4.4.2 Protocol Rev in Use
CP → PS → CP Protocol Rev in use
This command returns the protocol revision in use for the mobile which responds as follows:
17:05:46.6< ETS, Id=CP Protocol Rev in use
17:05:46.7> ETS, Id=CP Protocol Rev in use, P_REV in use=IS_2000
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 18
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
4.4.3 OOS Parameters
CP → PS → CP OOS Area Parms
Sending this command with the default values shown disables the phone from going out of service
(sleep) when the base station is not available for an extended period of time.
Window Selections Definition
P1-P4 # of attempts in phase 1-4 P1 Delay-P4 Delay sec delay between phase 1-4 attempts P1 Cycles-P3 Cycles number of repeats of N attempts + a delay
4.4.4 Set Deep Sleep Slice Time
CP → UI → CP Set Deep Sleep Time Slice
Window Selections Definition
Send Send to perform the command. Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
Time Slice
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 19
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
4.5 Radio Control
4.5.1 Tx Pwr Detect Measurements Spy
Please refer to section 3.4 for detailed description.
4.5.2 RSSI for AMPS and CDMA
Please refer to section 3.1 for detailed description.
4.5.3 DSPM AFC Frequency Error Spy
DSPM → Spy → Rfc → DSPM Rfc Afc Freq Error
Window Selections Definition
Print If checked, the window will be printed onto the main log as a trace:
16:01:30.6> ETS, Id=DSPM Spy, SpyId=DSPM Rfc Afc Freq Error, Sys Time=0xa24ad630, Frequency Error (Hz)=-10, AFC PDM Value=0x087f,
AFC Enabled=1, Coarse Freq Error(Hz)=2100 Sys Time Display system time for reference. Frequency Error (Hz) Frequency error recorded. AFC PDM Value AFC PDM Value used. AFC Enabled AFC enabling state. Coarse Freq Error (Hz) Display coarse frequency error.
4.5.4 HWD Freq Channel Trace
Please see section 3.5 for detailed descriptions.
4.5.5 Pilot Strength Spy
Please see section 3.6 for detailed descriptions.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 20
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
5 Test/Debug Capability
5.1 Basics
5.1.1 Communication Port Configuration
USB Port
Debug -> Comm -> USB
Then the ETS will show the connect port as USB
Serial Port
Debug → Comm → Serial, to select a COM port for communicate with DUT.
CP -> Options, set the Initial Baud Rate as 115200.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 21
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
5.1.2 Loopback Test
Debug → Loopback
This function used to test the USB/COM communications with CP, DSPM, or DSPV.
Calls CP Loopback, DSPM Loopback, and DSPV Loopback.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 22
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections Definition
Number of Messages Number of messages sent. Number of Timeouts Number of failures. Number of Mismatches Number of differences between what was sent and what was received. Send One Start Loopback test, one click will only sends out one command. Cycle When checked, loopback test will continuously run until either Cycle is un-
checked or the Loopback window is closed. Will stop if you double clicked.
Windowed When checked, four loopback requests are sent before any reply is received.
Fixed Pattern The user can supply a pattern of choice. Multiple words can be sent with a size
Stop On Error Test will stop on timeout or mismatch errors. CP Tests the loopback with the CP. DSPM Tests the loopback with the DSPM. DSPV Tests the loopback with the DSPV. Message timeout in seconds Length of time the system will wait for a reply before issuing the message,
Disable Printing When checked, messages to the Main Log window are suspended.
Then sends and replies will alternate.
of: CP 0x00 – 0xff and 0x0000 – 0xffff for both DSPV and DSPM.
“15:44:32.4: Timeout on message loopback”
CP, DSPM, DSPV
Referring to Section 5.1.2 above, selecting CP, DSPM or DSPV for the loopback debug ensures
functionality of the specific sector in the mobile.
5.1.3 Raw Rx/Tx Serial Data
File → Raw → Tx or Rx
This command enables printing the raw data onto the Main Log window that describes the transfer of
serial data between ETS and the board.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 23
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
5.1.4 Enable Generic Ack
Debug → Enable Generic Ack
This command controls the display of the acknowledgement to any command sent from ETS to the
mobile. If enabled, a response message for each command is returned. A check mark displays next to the
command if enabled.
5.2 Test Modes
5.2.1 CP Sleep Control
CP → MON → CP Sleep Control
This command enables/disables the sleep operation of the CBP5.X software so the unit does/does not
power down for a sleep period and wakes up for only the wake-up period duration.
5.2.2 Slotted Mode Enable/Disable
CP → PS → Test mode → CP Test Modes
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 24
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
To disable slotted: Set Qualifier to “Off” and click “Send” (Value entry is ignored).
To enable slotted: Set Qualifier to “On” and click “Send” (Value entry is ignored).
5.2.3 Pwr Savings Mode Config
CP → HWD → Pwr Savings → CP Power Savings Mode Config
sets the power savings mode
Window Selections
Send -- Send to perform power savings mode configuration. Tack -- If checked, the window will remain after clicking “Send”. If not
Ctrl Mode Automatic Stack values are used – selections in Band and Channel are ignored. Disable Manual Values selected in Band and Channel are used Pwr Saving Mode Power Up Power Up Qpch CDMA Rx Acq CDMA Rx Voice/Data Mode Idle Mic On Spkr On Mic+Spkr On
Options Definition
checked, window will close after clicking “Send”.
5.2.4 Pwr Savings Config
CP → HWD → Pwr Savings→ CP Pwr Savings Config
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 25
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections
Send -- Send to perform power savings configuration. Tack -- If checked, the window will remain after clicking “Send”. If not
Ctrl Mode Automatic Stack values are used – Hw Blks and Status are ignored. Disable Manual Selections made under “Hw Blks” and “Status” are used. Hw Blks All Blocks This is the recommended setting for manual control. Status On To turn blocks ON. Off To turn blocks OFF.
Options Definition
checked, window will close after clicking “Send”.
5.2.5 Pwr Savings Status Get
CP → HWD→ Pwr Savings → CP Pwr Savings HW Status Get
This command responds with the ON/OFF states of blocks within the chip. An example is shown below:
5.2.6 Pwr Savings Get Mode
CP → HWD → Pwr Savings→ CP Pwr Savings Get Mode
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 26
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Below shows the command and respond while the mobile is in traffic:
5.2.7 Diagnostic Parameters (L1D, LMD)
5.2.8 Phone State And Event Control
CP → PS →CP Phone State and Event Count
Below shows an example when the mobile is on paging:
5.2.9 Get Retrievable Statistics
CP → PS →Retrievable Stat → CP Get Retrievable Statistics
Window Selections
Send Send to perform the command, with a response as follow:
Options Definition
16:24:10.6< ETS, Id=CP Get Retrievable Statistics, Statistics Counter Group=MUX1_REV_FCH
16:24:10.6> ETS, Id=CP Get Retrievable Statistics , Statistics Counter Group=MUX1_REV_FCH , MUX1 REV FCH 1=0x000000a7 , MUX1 REV FCH 2=0x0000000a , MUX1 REV FCH 3=0x00000000 , MUX1 REV FCH 4=0x00000014 , MUX1 REV FCH 5=0x00000024 , MUX1 REV FCH 6=0x00000049
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 27
Samsung Electro-Mechanics Co., Ltd. Proprietary
, MUX1 REV FCH 7=0x00000000 , MUX1 REV FCH 8=0x0000047e , MUX1 REV FCH 9=0x00000000 , MUX1 REV FCH 10=0x00000000 , MUX1 REV FCH 11=0x00000000 , MUX1 REV FCH 12=0x00000000 , MUX1 REV FCH 13=0x00000000 , MUX1 REV FCH 14=0x00000000
Tack If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”.
Statistics Counter Group
MUX1_FOR_FCH PAG ACC
MUX1_REV_FCH
REV 0
5.2.10 Timer Enable
5.2.11 PS Enable/Disable
CP Power:
CP → PS → UI Command → CP Power
This command enables/disables the protocol stack but does not perform any resets to the system. It
serves the same purpose as the “Power” button on the MMI, which in turn performs a soft reset to the
system.
5.2.12 OOS Parameter
Please refer to section 4.4.3.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 28
Samsung Electro-Mechanics Co., Ltd. Proprietary
5.2.13 Service Option - SO (TBD)
5.3 RF Interface and Control
5.3.1 CDMA Configuration
CP PLL Channel Config
RF → CP PSW PLL Channel Config
REV 0
Window Selections
Send -- Send to perform the PLL channel configuration. Tack -- If checked, the window will remain after clicking “Send”. If not
Ctrl Mode Automatic Stack values are used – selections in Band and Channel are ignored. Disable Manual Values selected in Band and Channel are used Band PCS Selects BAND_CLASS_1 AMPS (NONE) Cellular Selects BAND_CLASS_0 JTACS Selects BAND_CLASS_3 (Japanese Cellular) Korean KPCS Selects BAND_CLASS_4 (Korean PCS) 450M NMT Selects BAND_CLASS_5 Channel User defined channel number
Options Definition
checked, window will close after clicking “Send”.
CP PLL Register Config
CP Cal initialize
RF → CP Cal Initialize
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 29
Samsung Electro-Mechanics Co., Ltd. Proprietary
Window Selections Options Definition
Send -- Send to perform the Cal Initialize command. Tack -- If checked, the window will remain after clicking “Send”. If
Calib Mode NVRAM This loads DBM cache of the DB templates onto the SRAM
Default This loads a default cal file onto flash. Command “CP CAL
REV 0
not checked, window will close after clicking “Send”.
cache for execution.
Init NVRAM” (under RF) is needed in conjunction after the Cal Initialize command.
CP PDM Config
RF → CP PDM Config
Window Selections Options Definition
Send -- Send to perform PDM Configuration Control. Tack -- If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”.
Ctrl Mode Automatic Stack values are used – selections in PDM Number and Value
Manual Values selected in Band and Channel are used Disable PDM Number Battery Charge Battery Charge PDM value set Afc Automatic Frequency Control PDM value set Tx Agc TX AGC PDM value set Rx Agc RX ACG PDM Value set Value Hex value in the format of 0x0000
are ignored.
CP PDM Read value
RF → CP PDM Read Value
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 30
Samsung Electro-Mechanics Co., Ltd. Proprietary
Window Selections Options Definition
Send -- Send to perform specified PDM Read. Tack -- If checked, the window will remain after clicking “Send”.
PDM Number Battery Charge Battery Charge PDM value set Afc Automatic Frequency Control PDM value set Tx Agc TX AGC PDM value set Rx Agc RX ACG PDM Value set
REV 0
If not checked, window will close after clicking “Send”.
CP Get PLL Channel
RF → CP Get PLL Channel
Window Selections Definition
Send Send to perform the command of getting PLL channel, response as shown:
16:35:21.8< ETS, Id=CP Get PLL Channel 16:35:21.8> ETS, Id=CP Get PLL Channel, Band=BAND_A, Channel=0x00c9
Tack If checked, the window will remain after clicking “Send”. If not checked, window
will close after clicking “Send”.
Note, the returned value is in Hex mode.
CP RF Rx Reg Read (TBD)
RF RF Registers CP RF Rx Reg Read
→ →
This message will select the relevant RF registers based on the Radio Design selected by the “RF Target
Option” in Section 2.6
CP RF Rx Reg Write (TBD)
RF RF Registers CP RF Rx Reg W
→ →
rite
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 31
Samsung Electro-Mechanics Co., Ltd. Proprietary
This message will select the relevant RF registers based on the Radio Design selected by the “RF Target
Option” in Section 2.6
REV 0
CP RF Tx Reg Read (TBD)
RF RF Registers CP RF Tx Reg Read
→ →
This message will select the relevant RF registers based on the Radio Design selected by the “RF Target
Option” in Section 2.6
CP RF Tx Reg Write (TBD)
RF RF Registers CP RF Tx Reg Write
→ →
This message will select the relevant RF registers based on the Radio Design selected by the “RF Target
Option” in Section 2.6
5.3.2 CDMA Receiver
CP CDMA Receiver Control
RF → CDMA → CP CDMA Receiver Ctrl
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 32
Samsung Electro-Mechanics Co., Ltd. Proprietary
Window Selections Options Definition
Send Send to perform CDMA Receiver Control command. Tack If checked, the window will remain after clicking “Send”.
Mode Off Turn CDMA Receiver OFF. On Turn CDMA Receiver ON.
REV 0
If not checked, window will close after clicking “Send”.
CDMA PLL Channel Config
Freq Error Trace
RSSI Trace
HWD CP Serializer Trace
CP TRACE HWD CP Serializer
→ → →
This trace is useful for monitoring all the activity on the serializer bus, particularly for control of the RF
chips
HWD Freq Channel Trace
CP TRACE HWD CP Freq Channel
→ → →
This trace shows the channels which the CP cycles through while trying to acquire a Base Station.
L1D Search Results Active
Refer to 3.6
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 33
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Rx AGC Parameters (L1D)
Clear FER
5.3.3 CDMA Transmitter
CP CDMA Transmitter Control
RF → CDMA → CP CDMA Transmitter Ctrl
Window Selections Options Definition
Send Send to perform Transmitter control command. Tack If checked, the window will remain after clicking “Send”.
If not checked, window will close after clicking “Send”. Mode On Turn CDMA transmitter ON. Off Turn CDMA transmitter OFF.
DSPM Tx AGC Get Params
RF → CDMA → DSPM Tx AGC Get Parms
Window Selections Definition
Send Send to get the HW Value of the Tx AGC currently operating at, response as shown:
16:55:08.8< ETS, Id=DSPM Tx Agc Get Parms 16:55:08.8> ETS, Id=DSPM Tx Agc Get Parms, Power=0.000000, HW
Value=0x0994
Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
DSPM Tx AGC Config
RF → CDMA → DSPM Tx AGC Config
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 34
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections Options Definition
Send Send to perform Tx AGC control command. Tack If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”.
Ctrl Mode Automatic Stack values are used – selections in preceding entries are
ignored. Manual Values entered in the preceding entries are used. Method HW Value Set to use PDM value from the Tx AGC Cal table. Selecting
this ignores the field “Power(dBm)”. dB Gain Set to use “power” column from the Tx AGC Cal table for
reference to transmit. Selecting this ignores the field “HW
Val”. HW Val PDM value in Hex referenced from CP DB HWD Tx AGC
Hyst State Low/Mid/High Gain state for the transmitter. Power(dBm) Actual transmitted power in dBm referenced from CP DB
table.
HWD Tx AGC table.
CP CDMA Tx Test
RF → CDMA → CP Tx CDMA Test
Window Selections Options Definition
Send Send to enable TX CDMA test in specified Tx rate. Tack If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. Rate Tx Test Off Turn Tx OFF. Access Turn TX ON to full rate but transmit through Access channel. Tr Full Rate Turn Tx ON to full rate. This is used for debug purposes most. Tr ½ Rate Turn Tx ON to half rate. Tr ¼ Rate Turn Tx ON to quarter rate. Tr 1/8 Rate Turn Tx ON to eighth rate.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 35
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Tx Tone Test
RF → CP TX Tone Test
Window Selections Options Definition
Send -- Send to transmit a single tone from the transmitter instead of a
CDMA spectrum. Tack -- If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. Enable On/Off Turn TX tone ON or OFF. Amplitude -- Amplitude of tone desired, typical value: 0x0200, in Hex.
HWD CP Serializer Trace
HWD Freq Channel Trace
Tx AGC Parameters (L1D)
CP Tune Radio
Get RSSI
Rx Calibration
Signaling Tone Mode (TBD)
DSPV DSPV Amp Rev Path DSPV Amp Signalling Tone Mode
→ →
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 36
Samsung Electro-Mechanics Co., Ltd. Proprietary
Set Busy Idle Status
Tx Fixed Freq
Tx Calibration
5.3.4 AFC
DSPM AFC Get Params
DSPM AFC Config
AFC Cal Parameters (L1D)
5.3.5 RF Pin Control
REV 0
CP TXON Control
RF → CP TXON Control
Window Selections Options Definition
Send -- Send to enable TXON Control Tack -- If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. TxOn [0:4] Off Turn TxOn OFF. On Turn TxOn ON. Auto Allow CBP software to control the TxOn
CP RXON Control
RF → CP RXON Control
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 37
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections Options Definition
Send Send to enable RFON Control Tack If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. RfOn [0:7] Off Turn RfOn OFF. On Turn RfOn ON. Auto Allow CBP software to control the RfOn
CP TXON Read
RF → CP TXON Read
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 38
Samsung Electro-Mechanics Co., Ltd. Proprietary
CP RXON Read
RF → CP RXON Read
REV 0
5.3.6 GPIO Control
GPIO Read / GPIO Write
CP → MON → GPIO → CP Read GPIO
Window Selections Options Definition
Send --
Tack -- If checked, the window will remain after clicking “Send”. If not
GPIO Num [0:47] Read the Relevant GPIO
Send to read the relevant GPIO. Caution: This command will set the GPIO to INPUT mode and perform the read. The original state is not preserved so this command should only be performed on GPIOs which are known to be Inputs.
checked, window will close after clicking “Send”.
CP → MON → GPIO → CP Set Clear GPIO
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 39
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections Options Definition
Send Send to read the relevant GPIO Tack If checked, the window will remain after clicking “Send”.
If not checked, window will close after clicking “Send”. GPIO Num [0:47] Read the Relevant GPIO Action SET Sets the GPIO to “0” CLEAR Clears the GPIO to “1”
GPIO Read Monitor
CP → MON →GPIO → CP Monitor GPIO
Window Selections Options Definition
Send -- Send to Monitor the relevant GPIO Tack -- If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”.
GPIO Num [0:47]
GPIO (trace ???)
5.3.7 Serializer
This section should be read in conjunction with the Serial Programmer chapters in References [2][3].
Serializer Configuration
CP → HWD → CP Serializer Config
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 40
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections Definition
Send Send to set the Serializer Configuration Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
Control Programs the register SER0_CTRL (listed as SER#_CTRL in Reference [3]). The PTR
field can only be set to “000”. Load Enable Programs the register SER0_LE (listed as SER#_LE in Reference [3]) NumBits-1 to Shift Programs the register SER0_BC (listed as SER#_BC in Reference [3])
Serializer Write
CP → HWD → CP Serializer Write
Window Selections Definition
Send Send to set the Serializer Configuration Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
Data Write Data to Serializer, which has been configured (see Section 0). This data is
loaded into the registers SER0_D1, SER0_D0 (listed as SER#_D1, SER#_D0 in Reference [3])
5.4 SMS
Here, we only provide a brief summary to allow the user the user to access the SMS menu. The details of
the SMS messages are covered in great detail in [6], while background information on SMS is provided in
[5].
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 41
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
5.4.1 Connect (CP PS SMS CP SMS Connect)
5.4.2 Disconnect (CP PS SMS CP SMS Disconnect)
5.4.3 Broadcast Connect (CP PS SMS CP SMS Bcast Connect)
5.4.4 Broadcast Disconnect (CP PS SMS CP SMS Bcast Disconnect)
5.4.5 User Ack (CP PS SMS CP SMS User Ack)
5.4.6 Service Option Pref (CP PS SMS CP SMS Srv Opt Pref)
5.4.7 Cancel (CP PS SMS CP SMS Cancel)
5.4.8 Broadcast Parameters (CP PS SMS CP SMS Bcast Parms)
5.4.9 Term Status (CP PS SMS CP SMS Term Status)
→→→→ →→→→ →→→→
→→→→ →→→→ →→→→
→→→→ →→→→ →→→→
→→→→ →→→→ →→→→
→→→→ →→→→ →→→→
→→→→ →→→→ →→→→
→→→→ →→→→ →→→→
→→→→ →→→→ →→→→
→→→→ →→→→ →→→→
5.4.10 Cause Code Status (CP PS SMS CP SMS Cause Code Stat
→→→→ →→→→ →→→→
5.5 Database Upload/Download
5.5.1 Flash Device
Flash Download for Reference Phones
1. Phone has been connected to the ETS.
2. Before you begin to download cp.rom, set Flash Download Timeout to 200. Open File-
>Options and then set Flash Download Timeout to 200, then click OK button, see the following
dialog box.
us)
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 42
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
3. Open File->Flash Download, you can see the flash memory download dialog, see the following
bitmap. Select the drop down box CP Boot for Flash Section; click the Browse to set your new
boot.rom path, set “wait for boot load command” check box on, then the “Download”
button will be disabled.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 43
Samsung Electro-Mechanics Co., Ltd. Proprietary
4. Power OFF the phone, connect the phone with PC and Power ON the phone, “Wait for boot
load command” check box becomes unchecked, and “Download” button is enabled.
REV 0
You will see “CP Boot Loader” in the ETS Log Window.
5. Click “Download” button to begin download boot.rom, you can see the CP Flash Download
dialog. ETS erases the flash, and then begin to write boot.rom in flash, and you can see the
download progress.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 44
Samsung Electro-Mechanics Co., Ltd. Proprietary
6. Open File->Flash Download, you can see the flash memory download dialog, see the following
bitmap. Select the drop down box CP for Flash Section; click the Browse to set your new
cp.rom path, set “wait for boot load command” check box on, then the “Download” button
will be disabled.
REV 0
7. Power OFF the phone, then Power ON the phone again, “Wait for boot load command” check
box becomes unchecked, and “Download” button is enabled.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 45
Samsung Electro-Mechanics Co., Ltd. Proprietary
You will see “CP Boot Loader” in the ETS Log Window.
8. Click “Download” button to begin download cp.rom, you can see the CP Flash Download dialog.
ETS erases the flash, and then begin to write cp.rom in flash, and you can see the download
progress.
REV 0
9. After download finished, power off the phone (If there is a battery in your phone, please
remove and re-insert), then power on the phone.
Flash Download FOR CDS Products (NOT FOR Reference Phones)
File → Flash Download
Use to download CP Boot, CP, DSPM, and DSPV code to flash memory. System must be in boot mode to
download any section of flash. See Reference [8] for more details.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 46
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections
Flash Section: CP Boot Downloads CP Boot code to flash memory when Download is
CP Downloads CP code to flash memory when Download is clicked. DSPM Downloads DSPM code or DSPM patches to flash memory when
DSPV Downloads DSPV code or DSPV patches to flash memory when
ALL FLASH Downloads FLASH Image to flash memory when Download is
FSM_DATA/FSM
Path Select recent paths or Browse mounted disks Print Cmds Used to print the commands sent from ETS to the Flash. Print Response Used to print the responses sent from Flash to ETS. Download Execute download of selected file Exit Close window
Options Definition
clicked.
Download is clicked.
Download is clicked.
clicked. Downloads File system to flash memory when Download is clicked.
_USER
Flash Program
CP → Flash → CP Flash Program
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 47
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Flash ID
CP → Flash → CP Flash ID
Used to display the type and manufacture of the Flash device in usi. The customer must update
hwdflash.c
if any other than the AMD AM29DL163CB flash is used.
Window Selections Definition
Send Data that is displayed in the Main Log window when Send is clicked in the above
example.
10:17:40.1< ETS, Id=CP Flash Id 10:17:40.1> ETS, Id=CP Flash Id, Manf Id=0x0001, Dev Id=0x002b
In this example, the flash used is an AM29DL163CB manufactured by AMD. See hwdflash.c for more details.
Tack When checked, window will remain on screen after every Send. When not
checked, window will close after a Send
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 48
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Flash Erase
CP → Flash → CP Flash Erase
Window Selections Options Definition
Send Data that is displayed in the Main Log window when Send is clicked
in the above example.
Tack When checked, window will remain on screen after every Send.
When not checked, window will close after a Send Section Type CP Boot Selects the CP Boot section of Flash. CP Selects the CP section of Flash. DSPM Selects the DSPM section of Flash. DSPV Selects the DSPV section of Flash All Selects all sections of Flash.
Configure Timers
IQ Polarity
Tx Voice Mode
Random Distribution
Rx Word Sync
Rx RSSI
AFC
Tx Levels
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 49
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
5.5.2 RF Calibration Data
Hwd AFC Data
CP→DB→DB Templates→Common→CP DB HWD AFC Data
Hwd Battery Data
CP→DB→DB Templates→Common→CP DB HWD Battery Data.
Hwd Temperature Data
CP→DB→DB Templates→Common→CP DB HWD Temperature Data
Hwd Aux ADC Data
Hwd PDM Data
CP→DB→DB Templates→Common→CP DB HWD PDM Voltage Data
Hwd Bandgap Trim Data
CP→DB→DB Templates→Common→CP DB HWD BandGap Trim Data
Hwd Misc Cal Data ?
PCS Tx AGC
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx AGC
PCS Tx AGC Freq Chan Adj
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx AGC Freq Chan Adj
PCS Tx AGC Temp Adj
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx AGC Temp Adj
PCS Tx AGC Battery Voltage Adj
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx AGC Batt Volt Adj.
PCS Tx AGC Limit Freq Chan Adj
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx Limit Freq Chan Adj
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 50
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
PCS TxAGC Limit Temperature Adjustment
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx Limit Temp Adj.
PCS TxAGC Closed Loop RF Power Measurement
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx Pwr Detect
PCS TxAGC Closed Loop Frequency Channel Adjustment
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx AGC Pwr Det Freq Chan Adj.
PCS TxAGC Closed Loop Battery Voltage Adjustment
CP→DB→DB Templates→ BAND B → CP DB HWD BAND B Tx Pwr Det Max Pwr Batt Voltage Adj.
PCS TxAGC Closed Loop Temperature Adjustment
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Tx AGC Pwr Det Temp Adj.
PCS Rx AGC
CP->DB->DB Templates-> BAND B ->CP DB HWD BAND B RxAGC CP DB HWD PCS RxAGC
PCS Rx AGC Freq Chan Adj
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Rx AGC Freq Chan Adj
PCS Rx AGC Temp Adj
CP→DB→DB Templates→ BAND B →CP DB HWD BAND B Rx AGC Temp Adj
CELL Tx AGC
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx AGC
CELL Tx AGC Freq Chan Adj
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx AGC Freq Chan Adj
CELL Tx AGC Temp Adj
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx AGC Temp Adj
CELL Tx AGC Battery Voltage Adj
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx AGC Batt Volt Adj.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 51
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
CELL Tx AGC Limit Freq Chan Adj
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx Limit Freq Chan Adj
CDMA TxAGC Max Power Limit Temperature Adjustment
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx Limit Temp Adj.
CELL TxAGC Closed Loop RF Power Measurement
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx Pwr Detect
CELL TxAGC Closed Loop Frequency Channel Adjustment
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx AGC Pwr Det Freq Chan Adj.
CELL TxAGC Closed Loop Battery Voltage Adjustment
CP→DB→DB Templates→ BAND A → CP DB HWD BAND A Tx Pwr Det Max Pwr Batt Voltage Adj.
CELL TxAGC Closed Loop Temperature Adjustment
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Tx AGC Pwr Det Temp Adj.
CELL Rx AGC
CP->DB->DB Templates-> BAND A ->CP DB HWD BAND A RxAGC CP DB HWD CELL RxAGC
CELL Rx AGC Freq Chan Adj
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Rx AGC Freq Chan Adj
CELL Rx AGC Temp Adj
CP→DB→DB Templates→ BAND A →CP DB HWD BAND A Rx AGC Temp Adj
5.5.3 Non-RF Database
Init MS capabilities
CP → PS → Database → CP Init MS Cap Db
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 52
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Clear MRU
CP → PS →Database→ CP Clear MRU
Window Selections Definition
Send The MRU (Most Recently Used Channels) is a list of (Band, Channel #) which is
stored in Flash. At Power Up the CBP4 software first scans the channels in the MRU, and then goes to the PRL. Clearing the MRU ensures that the PRL will be scanned first.
This command is particularly useful when a new PRL is downloaded to the phone.
Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
Init NAM
CP → PS →Database→ CP Init Nam
Window Selections Definition
Send Initializes the NAM with default values Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
Select Active NAM
CP → PS → Database → CP Select Active NAM
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 53
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections Options Definition
Send -- Send to set the active NAM Tack -- If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. Active NAM NAM1 Select “NAM1” as the active NAM NAM2 Select “NAM2” as the active NAM
Get active NAM
CP → PS → Database → CP Get Active Nam
Window Selections Definition
Send Send to get the active NAM Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
NAM Lock, Unlock
CP → DB → CP DB NAM Lock
Window Selections Options Definition
Send Send to Lock/Unlock the Active NAM Tack If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. DB NAM Status Lock This option locks the NAM and prevents modifications Unlock This option unlocks the NAM and allows modifications Confirm Change Yes Confirm the change you will perform No
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 54
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Set the A-Key
CP PS
→ →
Database CP Enter A Key→
Window Selections Options Definition
Send Send to write the A-Key A-Key 20 decimal digit A-Key Checksum 6 digit checksum ESN 32-bit (8 hexadecimal) ESN
Some Notes Regarding this command:
1. The A-Key is only updated in the Active NAM. Therefore the Select Active NAM command
should be executed prior to this Akey command to explicitly select the NAM where the Akey
should be updated.
2. The ValidAkey field in the NAM is asserted after this command is executed
3. The entire Checksum of the NAM structure is updated after this command is executed. To
be explicit, please note that this NAM checksum is independent of the A-key checksum.
4. There is also a tool help you calculate A-Key checksum, find it from Utilities->A Key
Calculator. Put the Akey and ESN number into calculator, click “Calculate Checksum” .
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 55
Samsung Electro-Mechanics Co., Ltd. Proprietary
Data services
PRL
Voice Memo 1
Voice Memo 2
Voice Rec 1
Voice Rec 2
5.5.4 DB Clear, Flush, Cache
5.5.5 DB Write
REV 0
5.5.6 DB Read
5.6 Software Operation Status
5.6.1 Software Version CP, DSPM, DSPV, ETS
CBP Version
CP → MON → CBP Version
Window Selections Definition
Send Send to Log Details of CBP version in the ETS Main Log Window Tack If checked, the window will remain after clicking “Send”. If not checked, window
will close after clicking “Send”.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 56
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
CP Version
CP → MON → CP Version
Window Selections Definition
Send Send to Log Details of CP Flash code in the ETS Main Log Window Tack If checked, the window will remain after clicking “Send”. If not checked, window
will close after clicking “Send”.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 57
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
DSPM Version
DSPM → DSPM Version
Window Selections Definition
Send Send to Log Details of DSPM Flash code in the ETS Main Log Window Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
DSPV Version
DSPV →MON → DSPV Version
Window Selections Definition
Send Send to Log Details of DSPV Flash code in the ETS Main Log Window Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
ETS Version
Help → About EtsMain
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 58
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
5.6.2 Memory Peek
CP Peek
CP → MON → CP Peek
Window Selections Options Definition
Send -- Send to Peek the CP Memory Location(s) or Register(s) Tack -- If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”.
Address -- Address of CP Memory or Register
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 59
Samsung Electro-Mechanics Co., Ltd. Proprietary
Window Selections Options Definition
Words(16) -- Number of words, up to 16 to Peek. Valid values: 1-16 Addr Adv Memory (advanced by
2 bytes)
Register (advanced by
4 bytes)
REV 0
Use this option to Peek Memory
Use this option to Peek Registers
DSPM Peek
DSPM → DSPM Peek
Window Selections Options Definition
Send Send to Peek the DSPM Memory Location(s) or Register(s) Tack If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. Address Address of DSPM Memory or Register Words(16) Number of words, up to 16 to Peek. Valid values: 1-16
DSPV Peek
DSPV → MON → DSPV Peek
Window Selections
Send -- Send to Peek the DSPV Memory Location(s) or Register(s) Tack -- If checked, the window will remain after clicking “Send”. If not
Address -- Address of DSPV Memory or Register Words(16) -- Number of words, up to 16 to Peek. Valid values: 1-16
Options Definition
checked, window will close after clicking “Send”.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 60
Samsung Electro-Mechanics Co., Ltd. Proprietary
5.6.3 Memory Poke
CP Poke
CP → MON → CP Poke
REV 0
Window Selections
Send -- Send to Poke the CP Memory Location(s) or Register(s) Tack -- If checked, the window will remain after clicking “Send”. If
Address -- Address of CP Memory or Register Words(16) -- Number of words, up to 16 to Poke. Valid values: 1-16 Addr Adv Memory (advanced by 2
bytes)
Register (advanced by 4
bytes)
Options Definition
not checked, window will close after clicking “Send”.
Use this option to Poke Memory
Use this option to Poke Registers
DSPM Poke
DSPM → DSPM Poke
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 61
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Window Selections Options Definition
Send Send to Poke the DSPM Memory Location(s) or Register(s) Tack If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. Address Address of DSPM Memory or Register Words(16) Number of words, up to 16 to Poke. Valid values: 1-16
DSPV Poke
DSPV → MON → DSPV Poke
Window Selections Options Definition
Send Send to Poke the DSPV Memory Location(s) or Register(s) Tack If checked, the window will remain after clicking “Send”. If not
checked, window will close after clicking “Send”. Address Address of DSPV Memory or Register Words(16) Number of words, up to 16 to Poke. Valid values: 1-16
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 62
Samsung Electro-Mechanics Co., Ltd. Proprietary
5.6.4 Disabling All Spies And Traces
5.6.5 Msgs Buffer Stats Spy
CP → Spy → MON → CP Msg Buff Stats
REV 0
示消息 冲 的信息。
显 缓
Print
Sys Time Num Msg Buffs In Use
Max Num Msg Buffs Used
Num Msg Buffs[1:4] In Use
Max Num Msg Buffs[1:4]
Max Msg Buff[1:4] Size
区
Window Display Description
如果选中，窗口中的信息将显示在
当前从缓冲区 曾经从缓冲区 缓冲区 缓冲区 缓冲区
5.6.6 Msgs Mbox Stats Spy
CP → Spy → MON → CP Msg Mbox Stats
1-4
中分配的消息总数量
1-4
中分配的消息的最大数量
1-4
中，当前分配的消息数量
1-4
中，曾经分配的消息的最大数量
1-4
中，可分配的消息的最大字节数
main log window中
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 63
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
示任 消息 列的 。
显 务 队
Window Display Explanation
Print
Sys Time Task Id
Num Msgs
状
态
如果选中，窗口中的信息将显示在
任务
ID
任务消息队列中的消息数量
5.6.7 Msgs Buf Ptr Stats Spy
CP → Spy → MON → CP Msg Buff Ptr Stats
Samsung Electro-Mechanics Co., Ltd.
main log window中
Proprietary Page 64
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
示消息指 的有 信息。
显 针 关
Window Display Explanation
Print
Sys Time Alloc By Task
Sent To Task
Msg Id
如果选中，窗口中的信息将显示在
创建消息的任务 接收消息的任务 消息
ID
5.6.8 Action Time Stats
CP->Spy->MON->CP Action Time Stats
main log window中
Window Display Explanation
Print Sys Time Num Action Times In Use Max Num Action Times Used
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 65
Samsung Electro-Mechanics Co., Ltd. Proprietary
5.6.9 Clear TDSO Stats
5.6.10 Clear FER
5.7 CBP Hardware
5.7.1 HW Version
5.7.2 Reset Processor
CP, DSPM, DSPV
5.7.3 Initializing Hardware Control
5.7.4 Hwd Init
REV 0
CP → HWD → HWD Init
Window Selections Definition
Send Send to Initialize Hardware Drivers Tack If checked, the window will remain after clicking “Send”. If not checked, window will
close after clicking “Send”.
5.7.5 Aux ADC Get
CP → HWD → CP AUX ADC Get
Window Selections Options Definition
Send -- Send to Read the AUX ADC Channel
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 66
Samsung Electro-Mechanics Co., Ltd. Proprietary
Window Selections Options Definition
Tack -- If checked, the window will remain after clicking “Send”. If
AUX ADC Channel AUX ADC Ch[0-15] Read the Relevant AUX ADC Channel. There are 16
Tx PCG Sync Off Take the AUX ADC reading immediately On Wait till an Active PCG to make a measurement. This is
REV 0
not checked, window will close after clicking “Send”.
channels [0-15]
especially usefully for measuring Transmit Power from the Power Amplifier; selecting this option ensures that the Power Amplifier is ON.
6 Utilities
6.1 Virtual MMI
Utilities -> Virtual MMI Utility, operate the handset just link press keypad.
6.2 Script Utility
Utilities -> Script Utility
The following steps descript how to record an ETS script. Give an example of record data of command
cp->DB->DB Templates->common->cp DB NAM 1, CP/DB/DB Templates/cellular/CP DB HWD Rx AGC.
1. Connect the phone to your computer, make sure all connection is ok.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 67
Samsung Electro-Mechanics Co., Ltd. Proprietary
2. Open ETS.
3. Run script thru Utilities -> Script Utility. In the Script, Select Script->Record command to let
Script application in Recording status. Then Script.exe will record all commands that printed in ETS main
window.
REV 0
4. In ETS application, select CP->DB->CP DB NAM LOCK command to unlock the NAM. Then select
CP->DB->DB Templates->common->CP DB NAM 1 command to open the dialog of CP DB
NAM1. And select CP->DB->DB Templates->BAND A->CP DB HWD BAND A Rx AGC to open
the dialog of CP DB HWED Rx AGC. If you want record more you can select the commands you want
to record.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 68
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 69
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
5. Click the “Read” commands in all dialog, For example In CP DB NAM1 dialog press the key “Read” to
read NAM1 data from the phone, and in “CP DB HWD BAND A Rx AGC “ dialog , press the key “Read”
to read Rx AGC data from the phone.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 70
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 71
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
6. Then in ETS, click “Write” in all dialogs that you have opened. In CP DB NAM1 dialog press the key
“Write” to write NAM1 data into the phone, then this command will be printed in ETS main window
and be sent to Script.exe. It will be recorded in the Script.exe main window. In “CP DB HWD BAND A
Rx AGC “ dialog press the key “Write”, the Rx AGC data will be recorded into script main window.
(See Picture <4>)
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 72
Samsung Electro-Mechanics Co., Ltd. Proprietary
REV 0
7. Switch to script, select Script->Record, to stop recording the script, and save the script in a file.
The file will be saved as *****.srp. Then you have recorded the NAM1 data in a script file.
Note: Usually if you want to run the write NAM data into the phone, you should set the NAM unlock.
So you need add the command “
Change=No
“ in the first line of script file. This command can also be directory recorded into script
ETS, Id=CP DB NAM Lock, DB NAM Status=Unlock, Confirm
file. The script file is TXT file, so you can edit it, copy some ETS command into the file.
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 73
Samsung Electro-Mechanics Co., Ltd. Proprietary
1 2012-06-05
Created
2
2
Revision History
Revision Date Descriptions
REV 0
Samsung Electro-Mechanics Co., Ltd.
Proprietary Page 74
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use