1 2
BEFORE USING THE WASHER DESCRIPTION OF PARTS
SPIN DRYER LID
SPIN DRYER
BASKET
WASH TUB
WASH TUB LID
LINT FILTER
WASHING
WATER INLET
WATER DRAIN
HOSE
(WITHOUT PUMP)
SPRAY WATER
INLET
POWER CORD
INNER LID
PULSATOR
DRAIN FILTER
(With pump)
CAUTIONS
PRECAUTIONS WHEN OPERATING
In case of pump drained washer,
remove the cap-hose from
the drain hole.
Be sure that the washer is grounded.
To avoid electrical shock,use
a metal pipe for the ground
connection. But, don't ground
the washer with gas pipes or
telephone lines to avoid
dangers of explosion or lightning strike.
Do not put your hands into the spin
dryer basket when it is spinning.
Yo ur fingers can be caught
by spinning laundry and
damaged.
Ventilation
opening must not be obstructed
by carpeting when the washing machine is
installed on a carpeted floor.
If the supply
cord of this appliance is damaged,
it must only be replaced by a repair shop
appointed by the manufacturer,because
special purpose tools are required.
Warning to avoid overfilling and damages
this appliance must be filled with the operator
present using a moderate water supply
pressure only.
Never allow children to operate
or play with the washer.
Children playing with the washer
may accidentally fall into the
washing tub.
Be sure to cover with the inner
cover on laundry before spinning.
This prevents laundry from
being tossed out and damaged.
Before washing,check all pockets.
If nails or pins remain in pockets,they may
damage the washer or clothes.
Close the water tap a little if the
water pressure is too high.
To avoid water splashes,
close the wash tub lid.
Be sure lay the drain hose down
(in case no drain pump)
Never splash water on the control panel.
Disconnect the power cord from the
power supply when not in use.
Don't use excessively hot water.
(50˚C or more)
Plastic parts may be deformed or damaged.
Also, clothing may be deformed or decolored.
Be sure to keep the lid
closed during washing
and spinning.
When you open this lid while
the spin basket is spinning,
the spinning will be stopped
by brake system.
The plug’s shape
may not correspond
with this drawing.
1. WASH SELECTOR
This is used to select Soft or Normal mode.
2. WASH TIMER
This is used to set the wash time, 1-15 minutes.
3. CYCLE SELECTOR
This is used to select the Washing or draining.
4. SPIN DRY TIMER
This is used to set the spin time, 1-5 minutes.
5. WASH WATER INLET
Connect water supply hose here.
6. SPIN WATER INLET
Connect water supply hose here.
5 1 2 3 4 6
CONTROL PANEL
Soft
Drain
Wash Water Inlet
Wash Selector
Wash Timer
Cycle Selector
Spin Dry Timer
Spin Water Inlet
Normal
OFF
If the wash and spin time is set less than 1 minute, sometimes the timer will not be reset,
so you should first set the wash and spin timer to 2 minutes and then turn it back to
desired time.
WASHING PROCEDURE
3
SPIN DRY
1. Set the Cycle Selector knob to "OFF".
2. Connect the water supply hose to the Wash
Water Inlet.
3. Set the Wash Selector knob to "Soft" or
"Normal".
1. Transfer the clothes into the spin basket
and arrange the clothes evenly.
2. Be sure to attach the safety cover and
close the inner lid.
3. Close the spin dryer lid.
4. Set the Spin Dry Timer 1-5 minutes.
TO WASH
4. Add appropriate amount of detergent and
load laundry in the wash tub.
Connect the other end of the water supply hose
to a water tap and then open the tap.
When a suitable water level is reached, turn the
tap off.
5. Set the Wash Timer 1-15 minutes.
6. After washing, set the Cycle Selector knob
to 'Drain' for draining.
4
OVERFLOW RINSE
3. As soon as the Wash Timer shuts off,
turn off the water tap.
4. Set the Cycle Selector knob to 'Drain' for
draining ".
1. Connect the water supply hose to the
Wash Water Inlet and the other end to a
water tap.
Be sure to select an appropriate flow (adjusting
the water tap) to prevent waste and splash of
water.
2. Set the Wash Timer to 6-8 minutes.
SPRAY RINSE
1. Load the laundry evenly into the
spin basket.
2. Press the laundry evenly, put the safety
cover into the basket and close the inner lid.
3. Close the spin dryer lid.
4. Connect the water supply hose to a water
tap and open it to supply water.
5. Set the Spin Timer to 2-3 minutes.
RINSING
1. Set the Cycle Selector knob to "OFF".
2. Load the laundry into the basket and
connect the water supply hose to the Wash
Water Inlet. Be sure that water does not
overflow the top of the wash tub.
3. Set the Wash Timer to 2-3 minutes.
4. After washing, set the Cycle Selector knob
to 'Drain' for draining.
Repeat this cycle until drain water is clean.
(2-3 cycles)
If the washer is placed on an uneven or weak surface, noise or vibration may be occurred.
Leave some space.
Decide the laying route of drain hose.
Space at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface.
Place the washer in good ventilation and
avoid direct sunlight.
Never place the washer in cold weather
condition or the place with fumes.
ENVIRONMENT
INSTALLATION