Samsung WF42H5600AW/A2-00, WF42H5600AP/A2-00 Owner’s Manual

the possibilities

Thank you for purchasing this Samsung product.

INSTALLING YOUR WASHER

OPERATING INSTRUCTIONS

11 Unpacking your washer
11 Overview of your washer
12 Electrical

12 Grounding
12 Water

13 Drain facility
13 Flooring
13 Location considerations
13 Alcove or closet installation

13 Undercounter installation (washer only)
14 With optional pedestal base or stacking kit

15 Important note to installer
15 Installation flow chart

18 Loading your washer
18 Washing clothes: Basic Instructions

WASHING A LOAD OF LAUNDRY

MAiNTAiNiNG YOUR WASHER

TROUBLESHOOTING

19 Overview of the control panel
21 Child Lock I_

22 Spin Only
22 Garment+ _+

22 Delay End
23 My Cycle

23 Smart Care
24 Washing clothes using the cycle selector

25 Using steam wash
25 ATC (Auto Temperature Control)

26 Detergent use
26 Features

28 Cleaning the exterior
28 Cleaning the interior
28 Cleaning the dispensers

28 Storing your washer
29 Cleaning the debris filter

30 Cleaning the door diaphragm
30 Preserving the top cover and the front frame

31 Self Clean+

32 Check these solutions if your washer.,.
34 Information codes

APPENDIX

i;

36 Fabric care chart
37 Cycle chart

39 Helping the environment
39 Declaration of conformity

39 Specification

_f tv nforrn _ton

J

Congratulations on your new Samsung washer. This manual contains important
information on the installation, use, and care of your appliance. Please take time

to read this manual to take full advantage of your washer's many benefits and

features.

WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and

situations that may occur. It is your responsibility to use common sense, caution, and care when installing,
maintaining, and operating your washer.

IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS

What the icons and signs in this user manual mean:

Hazards or unsafe practices that may result in severe personal injury

or death.

WARNING To reduce the risk of fire, explosion, electric shock, or personal injury

when using your washer, follow these basic safety precautions:

Z_ Hazards or unsafe practices that may result in minor personal injury or

CAUTION property damage.

Do NOT attempt.

Do NOT disassemble.

[_ Do NOT touch.

(_) Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.
_Read all instructions before the

using appliance.

SAVE THESE INSTRUCTIONS

English 3

/_ WARNING: To reduce the risk of fire, electric shock, or injury to when using

WARNINGappliance, follow basic precautions, including the following:

1. Read allinstructions before using the appliance.

2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked in,
or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances

as they give off vapors that could ignite or explode.

3. Do not allow children to play on or inthe appliance. Close supervision of children is
necessary when the appliance is used near children.

4. Before the appliance is removed from service or discarded, remove the door to the
washing or drying compartment.

5. Do not reach into the appliance ifthe drum is moving.

6. Do not install or store this appliance where it will be exposed to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any servicing unless
specifically recommended in the user-maintenance instructions or in published user-

repair instructions that you understand and have the skills to carry out.

9. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances
to the wash water. These substances give off vapors that could ignite or explode.

10. Under certain conditions, hydrogen gas may be produced in a hot water system that
has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. Ifthe hot

water system has not been used for such a period, before using a washer or combination
washer-dryer, turn on all hot water faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do
not smoke or use an open flame during this time.

persons your

_ State of California Proposition 65 Warnings:

WARNING

WARNING: This product contains chemicals known to the State of California to cause

cancer and reproductive toxicity.

SAVE THESE INSTRUCTIONS

SEVERE WARNING SIGNS FOR iNSTALLATiON

WARNING

Plug the power cord into an AC 120 V / 60 Hz / 15 A wall socket or higher and use the
socket for this appliance only. In addition, do not use an extension cord.

Sharing a wall socket with other appliances using a power strip or extending the power

cord may result in electric shock or fire.

Do not use an electric transformer. It may result in electric shock or fire.
Ensure that the power voltage, frequency and current are the same as those of the
product specifications. Failing to do so may result in electric shock or fire.

The installation of this appliance must be performed by a qualified technician or service
company.

Failing to do so may result in electric shock, fire, an explosion, problems with the
product, or injury.

Remove all foreign substances such as dust or water from the power plug terminals and
contact points using a dry cloth on a regular basis.

Unplug the power plug and clean it with a dry cloth.
Failing to do so may result in electric shock or fire.

Plug the power plug into the wall socket in the right direction so that the cord runs towards
the floor.

Ifyou plug the power plug into the socket in the opposite direction, the electric wires

within the cable may be damaged and this may result in electric shock or fire.

This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.

This may result in electric shock, fire, an explosion, or problems with the product

Never plug the power cord into a socket that is not grounded correctly and make sure

that it is in accordance with local and national codes.

Do not install this appliance near a heater or inflammable material.
Do not install this appliance in a humid, oily or dusty location, in a location exposed to direct

sunlight and water (rain drops).
Do not install this appliance in a location where gas may leak.

This may result in electric shock or fire.

Plug the power plug into the wall socket firmly. Do not use a damaged power plug,
damaged power cord or loose wall socket.

This may result in electric shock or fire.

Do not pull or excessively bend the power cord.
Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a heavy object on the power cord,
insert the power cord between objects, or push the power cord into the space behind the

appliance.

This may result in electric shock or fire.

Do not pull the power cord when unplugging the power plug.

Unplug the power plug by holding the plug.
Failing to do so may result in electric shock or fire.

SAVE THESE INSTRUCTIONS

English 5

When the power plug or power cord is damaged, contact your nearest service center.

CAUTION SIGNS FOR INSTALLATION

CAUTION

_This appliance should be positioned in such a way that it is accessible to the power plug.

Failing to do so may result in electric shock or fire due to electric leakage.

Install your appliance on a level and hard floor that can support its weight.

Failing to do so may result in abnormal vibrations, noise, or problems with the product.

_ nplug the power plug when the appliance is not being used for long periods of time or

during a thunder/lightning storm.

A

SEVERE WARNING SIGNS FOR USING

WARNING

Failing to do so may result in electric shock or fire.

lf the appliance is flooded, cut the power immediately and contact your nearest service
center.

Ifthe appliance generates a strange noise, a burning smell or smoke, unplug the power
plug immediately and contact your nearest service center.

Failing to do so may result in electric shock or fire.

In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without
touching the power plug. Do not touch the appliance or power cord.

Do not use a ventilating fan.
A spark may result inan explosion or fire.

Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or
other flammable or explosive substances.

This may result inelectric shock, fire or an explosion.

Do not open the washer door by force while it is operating (high-temperature washing/
drying/spinning).

Water flowing out of the washer may result in burns or cause the floor to be slippery.
This may result in injury.
Opening the door by force may result in damage to the product or injury.

Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the
washer before using it.

Do not insert your hand under the washer.

This may result in injury.

SAVE THESE INSTRUCTIONS

Do not touch the power plug with wet hands.

This may result in electric shock.

Do not turn the appliance off by unplugging the power plug while an operation is in
progress.

Plugging the power plug into the wall socket again may cause a spark and result in

electric shock or fire.

Keep all packaging materials well out of the reach of children, as packaging materials can
be dangerous to children.

Ifa child places a bag over their head, they may result in suffocation.

Do not let children or infirm persons use this washer unsupervised.

Failing to do so may result in electric shock, burns or injury.

Do not insert your hand or a metal object under the washer while it is operating.

This may result in injury.

Make sure the detergent drawer is closed before you put laundry into the washer or remove
laundry from the washer.

Ifthe detergent drawer is open, you could strike the drawer with your head and injure

yourself.

,} Do not attempt to repair, disassemble, or modify the appliance yourself.

Do not use any fuse ( such as cooper, steel wire, etc.) other than the standard fuse.

When repairing or reinstalling the appliance is required, contact your nearest service
center.

Failing to do so may result in electric shock, fire, problems with the product, or injury.

lf any foreign substance such as water has entered the appliance, unplug the power plug
and contact your nearest service center.

Failing to do so may result in electric shock or fire.

When the water supply hose comes loose from the faucet and floods the appliance, unplug
the power plug.

Failing to do so may result in electric shock or fire.

If any foreign substance enters the appliance, unplug the power plug and contact you
nearest service center.

Failing to do so my result in electric shock or fire.

SAVE THESE INSTRUCTIONS

English 7

CAUTION SIGNS FOR USING

CAUTION

When the washer is contaminated by a foreign substance such as detergent, dirt, food

waste, etc., unplug the power plug and clean the washer using a damp and soft cloth.

Failing to do so may result in discoloration, deformation, damage or rust.

The front glass may be broken by a strong impact. Take care when using the washer.

When the glass is broken, it may result in injury.

After a water supply failure or when reconnecting the water supply hose, open the faucet

slowly.
Open the faucet slowly after a long period of non-use.

The air pressure in the water supply hose or the water pipe may result in damage to a
part or in water leakage.

Ifa drain error occurs during an operation, check if there is a draining problem.

If the washer is used when it is flooded because of a draining problem, it may result in
electric shock or fire due to electric leakage.

Insert the laundry into the washer completely so that laundry does not get caught in the
door.

If laundry gets caught in the door, it may result in damage to the laundry or the washer,
or result in water leakage.

Ensure that the faucet is turned off when the washer is not being used.

Ensure that the screw on the water supply hose connector is properly tightened.
Failing to do so may result in property damage or injury.

Take care that the Rubber Seal and the Front Door Glass are not contaminated by a foreign

substance (e.g. waste, thread, hair, etc.).

If a foreign substance is caught in the door or the door is not completely closed, it may
cause a water leakage.

Open the faucet and check if the water supply hose connector is firmly tightened and that
there is no water leaking before using the product.

If the screws or the water supply hose connector are loose, it may result in water leak.

The product you have purchased is designed for domestic use only.
The use for business purposes qualifies as product misuse. In this case, the product will not

be covered by the standard warranty provided by Samsung and no responsibility can be
attributed to Samsung for malfunctions or damages resulting from such misuse.

Ifthe wash is not started and the laundry is left for a period of time after you have added
detergent or applied stain remover or pre-treatment onto the laundry, the laundry may be
discolored.

Select the recommended cycle and temperature on the basis of the laundry items, sort the
laundry by color on the basis of its colorfastness and select the appropriate cycle.

Make sure that foreign objects such as pins, buttons and coins are removed from clothing
items when adding laundry to the washer. Wash dirty laundry separately from relatively

clean items and wash fragile items separately from tougher textiles.
Ifan item is stained, wash it as soon as possible. Use stain remover or detergent only after

testing the colorfastness of the item by applying a small quantity to an inside seam.

SAVE THESE INSTRUCTIONS

Do not stand on top of the appliance or place objects (such as laundry, lighted candles,
lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.

This may result in electric shock, fire, problems with the product, or injury.

Do not operate the appliance with wet hands.

This may result in electric shock.

Do not spray volatile material such as insecticide onto the surface of the appliance.

As well as being harmful to humans, it may also result in electric shock, fire or problems
with the product.

Do not place an object that generates a electromagnetic field near the washer.

This may result in injury due to a malfunction.

Since the water drained during a high-temperature wash or drying cycle is hot, do not touch
the water.

This may result in burns or injury.

Do not wash, spin or dry water-proof seats, mats or clothing (*).

Do not wash thick, hard mats even if the washer mark is on the care label.

This may result in injury or damage to the washer, walls, floor or clothing due to
abnormal vibrations.

* Woolen Bedding, rain covers, fishing vests, ski pants, sleeping bags, diaper covers,

sweat suits, and bicycle, motor cycle, car covers, etc.

Do not operate the washer when the detergent box is removed.

This may result in electric shock or injury due to water leakage.

Do not touch the inside of the tub during or just after drying as it is hot.

This may result in burns.

Do not insert your hand into the detergent dispenser after opening it.

This may result in injury as your hand may be caught.

Do not place any objects (such as shoes, food waste, animals) other than laundry into the
washer.

This may result in damage to the washer, or injury and death in the case of pets due to
the abnormal vibrations.

Do not press the buttons using sharp objects such as pins, knifes, fingernails, etc.

This may result in electric shock or injury.

Do not wash laundry contaminated by oils, creams or lotions usually found in skincare
shops or massage clinics.

This may result in the rubber seal becoming deformed and water leakage.

Do not leave metal objects such as a safety pin or hair pin, or bleach in the tub for long
periods of time.

This may cause the tub to rust.

Ifrust starts appearing on the surface of the tub, apply a cleansing agent (neutral) to the

surface and use a sponge to clean it. Never use a metal brush.

SAVE THESE INSTRUCTIONS

English 9

Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry
contaminated by dry cleaning detergent.

This may result inspontaneous combustion or ignition due to the heat of the oxidation of
the oil.

Do not use hot water from water cooling/heating devices.

This may result in problems with the washer.

Do not use natural hand-washing soap for the washer.

If it hardens and accumulates inside the washer, it may result in problems with the
product, discoloration, rust or bad odors.

Do not wash large laundry items such as Bedding in the washing net.

Failing to do so may result in injury due to abnormal vibrations.
Place smaller items, such as lace socks and lingerie in the washing net.

Do not use hardened detergent.

If it accumulates inside the washer, it may result in water leakage.

Do not wash throw rugs or doormats.

Ifyou wash throw rugs or doormats, the sand will accumulate inside the washer. It may
result in error such as no draining.

Take care that children's fingers are not caught in the door when closing it. This may result

A

! SEVERE WARNING SIGNS FOR CLEANING

WARNING

in injury.

Do not clean the appliance by spraying water directly onto it.

G

Do not use the strong acid cleaning agent.
Do not use benzene, thinner or alcohol to clean the appliance.

This may result in discoloration, deformation, damage, electric shock or fire.

Before cleaning or performing maintenance, unplug the appliance from the wall socket.

Failing to do so may result in electric shock or fire.

SAVE THESE INSTRUCTIONS

UNPACKING YOUR WASHER

Unpack your washer and inspect it for shipping damage. Make sure you have received all the items
shown below. Ifyour washer was damaged during shipping, or you do not have all of the items, contact
1-800-SAMSUNG (726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.

Z_ Packing materials can be dangerous to children. Keep all packing material (plastic bags, polystyrene,

....... etc.) well out of the reach of children.

OVERVIEW OF YOUR WASHER

Detergent drawer

Control panel

Door

Tub

Debris filter

Drain tube

Filter cover

Hot water supply

hose

Cold water supply

Drain Hose

Adjustable legs

Wrench Bolt Hole Covers

Plastic Zip Hose Tie anti-slip pads

[_* Bolt hole covers ' The number of bolt hole covers depends on the model (3-6 covers).

Water Supply Hoses

Hose Guide

BASIC LOCATION REQUIREMENTS

Electrical

120 Volt 60 Hz 15 AMP fuse or circuit breaker

Individual branch circuit serving only your washer is recommended.
Your washer is equipped with a power cord.

Z_ NEVER USE AN EXTENSION CORD.

CAUTION

Grounding

ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE,

This appliance must be grounded. In the event of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a power cord having a three-prong grounding plug for use in a

properly installed and grounded three-prong outlet.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

_An improperly connected equipment-grounding conductor can increase the risk of electrical

....... shock. Check with a qualified electrician or serviceman if you are not sure whether the

appliance is properly grounded. Do not modify the plug provided with the appliance - if it
does not fit the outlet, have a proper outlet installed by a qualified electrician.

IMPORTANT SAFETY PRECAUTIONS

To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and
grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No.
70 Latest Revision and local codes and ordinances. It is the personal responsibility of the

appliance owner to provide adequate electrical service for this appliance.

/_ NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR

....... HOT WATER PIPES.

Water

Using bad quality water may cause the water supply valve to operate abnormally.

To correctly fill your washer in the proper amount of time, water pressure of 20-116 psi (137-

800 kPa)is required.

Water pressure less than 20 psi may cause water valve failure, may not allow the water valve to

shut off completely, or may extend the fill time beyond what your washer controls allow, causing

your washer to turn off. A time limit is built into the controls to prevent extensive flooding in your

home if an internal hose becomes loose.

The water faucets must be within 4 feet / 122 cm of the back of your washer to match the inlet

hoses provided with your washer.

[_ ccessory inlet hoses are available in various lengths up to 10 feet/305 cm for faucets that

are further away from the back of your washer.

To avoid the possibility of water damage:

,, Have water faucets easily accessible.
,, Turn off faucets when the washer is not in use.

,, Periodically check that there is no leakage from the water inlet hose fittings.
CHECK ALL CONNECTIONS AT THE WATER VALVEAND FAUCET FOR LEAKS.

WARNING

Drain facility

The recommended height of the standpipe is 18 in/46 cm. The drain hose must be routed
through the drain hose clip to the standpipe. The standpipe must be large enough to accept the
outside diameter of the drain hose. The drain hose is attached at the factory.

Flooring

For best performance, you must install your washer on a solidly constructed floor. Wood floors

may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting
and soft tile surfaces are contributing factors to vibration which can cause your washer to move
slightly during the spin cycle.

Never install your washer on a platform or weakly supported structure.

Location considerations

Do not install your washer in areas where water may freeze, since your washer will always retain
some water in its water valve, pump, and hose areas. Freezing water can damage the belts,the
pump, hoses and other components.

Alcove or closet installation

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides - 1 in / 25 mm Top - 17 in / 432 mm

Rear- 5.9 in / 150 mm Closet Front - 2 in / 51 mm

Ifthe washer and dryer are installed together, the closet front must have at least a 72 in2(465
cm 2)unobstructed air opening. Your washer alone does not require a specific air opening.
A. Recessed area

A

1 in,

(2.5cm)

_q rq

1in. ---_-14_- 27 in. ---"-_'1I_" 27in. _ 1in.

(2.5cm) (68.8cm) (68.6cm) (2.5cm)

B. Side view - closet or confined area

Undercounter installation (washer only)

m

(100.6 cm)

39.6in. _

I in. -..._I_.------ 27in. ----_I_ ..-I in.

(2.5ore) (68.6cm) (2.5ore)

With optional pedestal base or stacking kit

Required Dimensions for Installation With Pedestal (Model No : WE357"

51.2in.(130cm)toclearopendoor

(98.4)

387n:/

(84.8cm) (15cm)

[_e-5.9in.

......._ .... 53.4in. |

27in. ---------'_

(68.6cm)

(135.6cm)_

-_11_- 5in.

3 in,

(7.6cm)

3 in,

1in. -'_1 _'- 83.4in. ---_1 _- 5.9in.**

Closetor Door

Required Dimensions for Installation With Stacking Kit (Model No : SK-5A)

(7.80m)

(2.5cm) (84.8cm) (15cm) _,

(12.7cm)

©

77.5in.

(197cm)

©

* Required spacing
** External exhaust elbow requires

additional space.

IMPORTANT NOTE TO INSTALLER

Please read the following instructions carefully before installing the washer.

These instructions should be retained for future reference.
We recommend you hire a professional to install this washer.

Installation flow chart

Selectinga _ Removingthe shipping _ Connectingthewater

location bolts (*Drumonly) andthe drain

T

Please Adjusting the _ poweringyour washing

check again levellingfeet machine

before
steps.

[

Yes

STEP 1

Removing the Shipping Bolts

Before using your washer, you must remove allshipping bolts from the
back of the unit.

1, Loosen all the bolts with the supplied wrench.
2, Slide the bolt and spacer up and remove the bolt with the spacer

through the hole in the rear wall of your washer. Repeat for each
bolt.

3, Cover the holes with the supplied Bolt Hole Covers (Seepage 11).
4, Keep the shipping bolts and spacers for future use.

STEP 2
Selecting a Location

i i i ii i ii i

DOes

yourwasher

haveexcessvibration

ornoise?

No description)

Runninga Calibration mode

(RefertOthe following _ Finish the

installation

_ Before you install your washer, make sure the location:

Has a hard, level surface.
Is away from direct sunlight.
Has adequate ventilation.

Will not freeze (tempuratures are never below 32 °F or 0 °C).

Is away from heat sources such as oil or gas.
Has enough room for the power cord.
Doesn't have any carpeting that will obstruct ventilation openings.

STEP 3
Installing your Washer

1. If you use a standpipe, make sure the connection
between the drain hose and the standpipe is NOT

airtight. The standpipe must be at least 18 in or 46
cm high.

You must always exercise caution to avoid

collapsing or damaging the drain hose. For best
results, the drain hose should not be restricted

in any way - by elbows, couplings, or excessive
length. For situations where the drain hose cannot

be conveniently elevated to at least 18 in or 46 cm,
the drain hose must be supported.
If drain hose is installed below 18"(46cm), water
can be drained in cycle working cause of siphon
phenomenon. It causes the washer to "4E" error.

_ Drain Hose can be installed until 96"(245cm) maximum.

But drain capability can be reduced at this height.
It causes the washer to have an odor because of

remaining water in the drain system.

_ onnect the hose guide within 6"(15cm) from the end of

the drain hose. If the drain hose is extended more than
6"(15cm) beyond the end of the hose guide, mold or

microorganisms could spread to the inside of the washer.

2. Check the inlet hose to ensure a washer is inside each fill hose.
Thread the inlet hoses to the HOT and COLD faucet connections.

On the other end of the hose, check for one rubber washer per hose
and attach each fill hose to the water valve. Make sure the hose with
Hot printed on it is attached to the HOT faucet. Tighten by hand until
snug, then two-thirds of a turn with pliers.

For correct water use, connect both HOT and COLD water valves. If

either or both are not connected, an "4E" error can occur.

Laundry tub

Nomorethan!_i I_

6"(15cm)_...._

HoseGuide

Cold

Standpipe

Hot

Rubber

Washer

3. Turn on the "HOT" and "COLD "water supply and check the water
valve and the water supply connections for leaks.

Cold printed Hot printed

4, Slideyourwasherintoposition.
5, Levelyourwasherbyturningthelevelinglegsinoroutas

necessarybyhandorbyusingthewrenchincludedwithyour
washer.

Whenyourwasherislevel,tightenthelockingnutsusingthe
wrenchor(-)flatheadscrewdriver.

6, Plugthepowercordintoa3-Prong,wellgrounded120volt

60Hzapprovedelectricaloutletprotectedbya15-ampfuse
orcomparablecircuitbreaker.

Yourwasherisgroundedthroughthethirdprongofthe
powercordwhenpluggedintoathree-pronggrounded
receptacle.

Yourwashermustbeleveledonallfoursides.Acarpenter's

levelshouldbeusedonallfourcornersofyourwasher.We
recommendyourecheckyourwasherafteradozenorso
washestomakesureit'sstilllevel.

_ voiddamagetothelegs.Donotmove

thewasherunlesstheLocking-nutsare
fastenedtothebottomofthewasher.

Test run
Make sure that you install your washing machine correctly by running the Rinse+Spin cycle

after the installation is complete.

STEP 4
Calibration mode

Your Samsung washing machine automatically detects the weight of the laundry.

For more accurate weight detection, please run Calibration Mode after the installation.

To run Calibration Mode, follow these steps:

1. Turn on the washer.

2o Press the Tempo button and Belay End button simultaneously for at least 3 seconds.
3, Remove any contents in the tub and close the door.

4, Press the Start/Pause button.
5, The drum rotates clockwise and counterclockwise for approximately 3 minutes.

6, When Calibration Mode is finished, the "En/End" appears on the display and the washing

machine turns off automatically. The washing machine is now ready for use.

na n tnActon

I

/_To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

....... INSTRUCTIONS before operating this appliance.

LOADING YOUR WASHER

,, You can fill the tub with dry, unfolded clothes, but DO NOT OVERLOAD the tub. No more than 3/4 full.
,, Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or

wrinkling of the load.

,, Wash delicate items such as bras, hosiery, and other lingerie inthe Delicates cycle with similar

lightweight items.

,, When washing big bulky items or a few smaller items that don't fill the tub completely - a rug, a pillow,

stuffed toys, or one or two sweaters, for example - add a few towels to improve tumbling and spin

performance.

_ uring the spin cycle, the washer may add additional water to redistribute the clothes and correct an

inbalance inside the drum.

,, To ensure good cleaning result when washing heavily soiled loads, do not overload your washer.
,, When the "_+" light is ON (see page 22), you can add or remove laundry items during a wash.

1. Press the Start/Pause Button.
2, Wait for the Door Lock light to go out (5 seconds).
3, Add the item, close the door, and press the Start/Pause Button.

After a 10-second pause, the cycle will resume.

ensure

_To add items within five minutes of the wash

thorough cleaning, starting cycle.

WASHING CLOTHES: BASIC INSTRUCTIONS

1. Press the Power button, open the door, and then load the washer.

2, Close the door.
_Push the laundry into the drum completely to prevent the laundry from being caught in the door or

....... from falling out of the drum.

3, Add detergent and additives to the dispenser (see pages 27-28).
4, Select the appropriate cycle and options for the load (see pages 19 -21 and 24).
5, Press the Start/Pause Button.

The drum automatically rotates and measures the weight of the laundry without supplying water in
order to adjust the wash time. (The rotating display on the display panel indicates that the weight of the

laundry is being measured.)

6, The Wash Indicator light will illuminate.
7° The estimated cycle time will appear in the display.

The time may fluctuate to indicate the time remaining in the cycle better.

The actual time required for a cycle may differ from the estimated time inthe display depending on the
water pressure, water temperature, detergent, and laundry.

8. Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a
quick drain.

_ hen the cycle is complete, the Door Lock light will go out and "End" will appear in the display.

,, DO NOT attempt to open the door until the Door Lock light is off. To add a forgotten item, see the

"Loading your Washer" section above.
When your washer is restarted after a pause, expect a delay of up to 15 seconds before the cycle

continues.
,, Pressing the Power button cancels the cycle and stops your washer.
,, The Pre Wash, Wash, Rinse, and Spin indicator lights will illuminate during those portions of the

cycle.

ADo not place anything on top of your washer while it is running.

WARNING

DEEPSTEAM \ NORMAL/ ECOCOLD
HEAVYDUTY QUICKWASH
BEDDING PERMPRESS

SANITIZE__ WOOL

ALLERGE ICATES
RINSE+SPIN_X\ /_'_/J_ ACTIVE WEAR

[] Steam Cycles_

DEEP STEAM \ NORMAL i QUICK WASH

HEAVY DUTY TOWELS

BEDDING PERM PRESS

SANITIZE__ W00L

ALLEROE ICATES

RINSE+SPIN _,_\\ j/_-- ACTI ......

[] Steam Cycles _,L _//

\ /

I

@ @ @ @ @ @ @ @

Select the appropriate cycle for the type of load.
This will determine the tumble pattern and spin speed for the cycle.

To minimize of select the Perm Press

DEEP STEAM - For heavily soiled, colorfast garments, this cycle provides a

high washing temperature and steam and is effective for cleaning stains.

HEAVY DUTY - For sturdy, colorfast fabrics and heavily soiled garments.
BEDDING - For bulky items such as blankets, comforters and sheets. When

you are washing bulky items, use liquid detergent.
SANITIZE - For heavily soiled, colorfast garments. This cycle heats the water

to 150 °F to eliminate bacteria.

If you select pause during the heating portion of the Sanitize Cycle, your
Washer door will remain locked for your safety.

When selecting this cycle, the water heats to an extra high temperature

to remove 99.9% of certain bacteria typically found on clothing, bedding,
or towels. This certification is conducted by NSF International, an

independent third-party testing and certification organization.
Please check the garment care label to avoid garment damage. Only

sanitizing cycles have been designed to meet the requirements of this
protocol for sanitization efficacy.

wrinkling laundry, cycle.

_ [ NSF Protocol P172

Sanitization Performance of Residential and
Commercial, Family-Sized Clothes Washers

ALLERGEN - This course is applied to remove dust mites, pet dander or
other allergic substances of the fabric.

Only ALLERGEN cycle has been designed to meet the requirement of

P351 for allergen reduction efficacy.

_S_ [ NSF Protocol P351

_ Commercial,Family-Sized Clothes Washers

Allergen Reduction Performance of Residential and

RINSE + SPIN - Use for loads that need rinsing only or to add rinse-added
fabric softener to a load.

NORMAL - For most fabrics including cottons, linens, and normally soiled
garments.

ECO COLD - It provides useful daily care for normally and lightly soiled
laundry by using only cold water, saving energy and caring fabric.(Only for

WF42 H5700A*)

QUICK WASH - For lightly soiled garments needed quickly.
TOWELS - For bath towels, washcloths, and mats.(Only for WF42H5600A*)

PERM PRESS - For wash-and-wear, synthetic fabrics, and lightly to normally
soiled garments.

WOOL - For machine-washable wool. Loads should be under 8 pounds. For
best results, we recommend a load of 4.4 pounds or less.

The Wool cycle washes laundry by moving the wash drum horizontally
to maintain the characteristics of the wool fibers and to prevent damage
to the cloth. It then stops for a while to allow the laundry to soak in the
water. This pause in the operation of the Wool cycle is normal.

,, We recommend you use a neutral detergent to prevent damage to the

cloth and to improve the washing results.
DEUCATES - For sheer fabrics, bras, lingerie silk, and other handwash-only
fabrics. For best results, use liquid detergent.

ACTIVE WEAR - Use this cycle to wash exercise wear such as sports
jerseys, training pants, shirts/tops and other performance clothing. This cycle

provides effective soil removal with gentle action for special fabric care.

The large Digital Display is easy to use. It provides instructions and

diagnostics while keeping you updated on the cycle status and time
remaining.

Press the button repeatedly to cycle through the different water temperature
options.

Extra Hot - Heavily soiled, colorfast items. Only available with the Sanitize
cycle.

Hot - Whites and heavily soiled, colorfast items.
Warm - Colorfast items. When warm rinse is selected, only the final rinse will

be warm.

The other rinses will be cold to conserve energy.

Eco Warm - Moderately soiled, colorfast items; most wrinkle-free items.
Cold - Brightly colored, very lightly soiled items.
Press the button repeatedly to cycle through the different spin speed options.

(Rins hold (AllLampTurnOff) ---)No Spin ---)Low ---)Medium ---)High ---)Extra
High)

Extra High - Removes more water from loads during spin.

To minimize wrinkling of wrinkle-free and no-iron fabrics, DO NOT use

the Extra High spin option for these loads, nor overload your Washer.

High - Use for underwear, t-shirts, jeans and sturdy cottons.
Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics.

Low - Use for delicate items needing a slow spin speed.
No Spin - Drains your Washer without spinning. Use for extremely delicate

items that cannot tolerate any spin.
Rinse Hold (AllLampTurnOff) - The laundry remains soaking inthe final rinse
water. Either a drain or spin cycle must be performed to unload the laundry.

Press the button to select the soil level/washing time.
(Light ---)V --_Normal ---)/_ --_ Heavy)

eavy - For heavily soiled loads.

Normal - For moderately soiled loads. This setting is best for most loads.

V

Light - For lightly soiled loads.

Pressthesebuttonstoselectdifferentcycleoptions.

PreWash-Tousethisfeature,adddetergenttotheprewashsectionofthe
detergentcompartment.Whenturnedon,thewasherfillswithcoldwaterand
detergent,tumbles,thendrainsandadvancestotheselectedwashcycle.

Somecyclescannotbeselectedwiththisoption(Seepage27-28).

ExtraRinse-Addanadditionalrinseattheendofthecycletoremove
laundryadditivesandperfumesmorethoroughly.

ExtraSpin-Addadditionaltimetoremovemorewaterfromloads.
Steam- PressthisbuttontousetheSteamWashfunction.SteamWashis

availablewiththeNormal,HeavyDuty,Bedding,Sanitize,DeepSteamand
Allergencycles.Forheavilysoiled,colorfastgarments,SteamWashimproves
staintreatmentanduseslesswater(Seepage25).
Sound-WhenyouactivatetheSoundofffunction,the"_" lampilluminates.

MyCycle-Chooseyourfavoritecycleincludingtemperature,spin,soillevel,
options,etc.(seepage23)

DelayEnd-Anycyclecanbedelayedforupto24hoursinone-hour
increments.Displayedhourindicatesthetimeatwhichthewashwillbe

started.(Seepage22).
SelfClean+- Usetocleandirtandpossiblemoldfromthedrum.Regular
use(afterevery40washes)isrecommended.Nodetergentorbleachis
needed(seepage31).

SuperSpeed-Pressthisbuttonifyouneedtoshortenthewashingtime,
applicableforNormal,Deepsteam,HeavyDuty,BeddingorAllergencourse.
TheshortenedtimemaydifferdependingontheCycles/Load/Option.

Presstopauseandrestartprograms.

Pressoncetoturnyourwasheron,pressagaintoturnyourwasheroff.If
thewasherisleftonformorethan10minuteswithoutanybuttonsbeing
touched,thepowerautomaticallyturnsoff.

Child Lock 6

Child Lock prevents children from playing with your washer.
Once you have activated the Child Lock function, the control panel cannot be activated,

preventing children from playing with the washer.

Activating the Child Lock function

Pressand hold both the Soil Level and Spin buttons simultaneously for 3 seconds.
,, When you activate the Child Lock function, the door locks and the "Child Lock I_" lamp

illuminates.

,, If you press the START/PAUSE button after you have activated the Child Lock function, none of

the buttons will work except for the POWER button.

,, If you press a button when the buttons are locked, the "Child Lock _" lamp blinks.

Pausing the Child Lock function

When the door is locked or the buttons are locked by the Child Lock function, you can pause the
Child Lock operation for 1 minute by pressing and holding both the Soil Level and Spin buttons
simultaneously for 3 seconds.

Ifyou pause the Child Lock mode temporarily, the door lock is released for 1 minute for user

convenience. During this period, the "Child Lock _" lamp blinks.

Ifyou open the door after the minute is over, an alarm sounds for up to 2 minutes.
Ifyou close the door within the 2 minutes, the door is locked and the Child Lock function is

reactivated. If you close the door after the 2 minutes, the door is not locked automatically and
no alarm sounds.

Deactivating the Child Lock function

Pressand hold both the Soil Level and Spin buttons simultaneouslyfor 6 seconds,

• Whenyou deactivatethe Child Lockfunction, the door isunlocked andthe "Child Lock6" is turned off.

//_o TheChild Lockfunction preventschildrenor the infirmfrom accidently operatingthe washerand

....... injuring themselves,

Ifachild entersthe washing machine,the child may become trapped and suffocate,
Once you haveactivated the Child Lockfunction, it continues working even ifthe power is turned

off,
Openingthe door by force can resultin injurydue to damageto the product.

z_To add laundryafter you haveactivatedthe Child Lockfunction, you must first pause or deactivate the

....... Child Lock function.

lfyou want to open the door of the washing machinewhen the Child Lock function isactivated:

Pauseor deactivatethe Child Lock function.
Turnthe washing machineoff and then on again.

Spin Only

Ifyou press the POWER button and then press and hold the Spin button for 3 seconds, the
spin time will be displayed on the display panel.

Then, press the Spin button repeatedly until the required spin level is selected, and then press

the START/PAUSE button.

_ Before pressing the Spin Only button to use the Spin Only function, you can select a cycle

with the Cycle Selector. Ifyou have selected a cycle, you can only select the spin level
corresponding to the selected cycle.

Garment+ _+

You can add or take out laundry items even after the wash has started, as long as the "_++" light

is on. Pushing the START/PAUSE button unlocks the door, unless the water is too hot or if there
is too much water in your washer. Ifyou are able to unlock the door and wish to continue the
wash cycle, close the door, and then press the START/PAUSE button.

Delay End

You can setthe washing machineto startyour wash automaticallyat a latertime, choosing a delay time.
The hour displayed indicatesthe time at which the wash will be ended.

1. Set yourwash Cycles.

2. Pressthe Belay End button repeatedlyuntilthe delaytime is set.

3. Pressthe START/PAUSEbutton, The "Delay EndQ" indicator will be lit, andthe clock will begin
counting down until it reachesthe set time,

4. Tocancel a Delay Endfunction, press the POWER button and thenturn the washing machineon
again.

My Cycle

Lets you save a custom wash cycle (temperature, spin, soil level, etc.) and then recall and use it

with one button convenience.
To save a cycle and selected options as your My Cycle, follow these steps:

1. Select the cycle using the Cycle Selector dial.

2. After cycle selection, set each option.
_See 39 for available with each

page

option settings cycle.

3. You can then store the selected cycle and options by pressing and holding the My Cycle

button for longer than 3 seconds. The cycle and options you select will be displayed the next
time you choose the My Cycle function.

4. Press the My Cycle button to load and use the saved My Cycle options. The "My Cycle" light

will indicate activation. Also, the chosen course and option lights will flicker

You can change the "My Cycle" settings by repeating the process above.
The washer displays the last settings used the next time you choose "My Cycle".

lf you press My Cycle and release it within 3 seconds, the previously saved cycles and

options appear. If you press and hold My Cycle for 3 second or longer, the currently set
cycles and options are saved and the LED blinks for 3 seconds.

Smart Care

This function enables you to check the status of the washing machine using a smartphone.

1. To enable the Smart Care function, press and hold the Super Speed button for 3 seconds

within 10 seconds after turning the power on by pressing the Power button.

2. Ifthe Smart Care function is activated, the LED on the

window display rotates for 2 or 3 seconds and then the
Smart Care indicator is lit on the display.

3. Run the Smart Care app on your smart phone.

4. The Smart Care function is optimized with Galaxy and iPhone

Series.

5. Focus your smart phone's camera on the display panel of

the washing machine.

6.

Ifthe smart phone's camera is focused on the display panel of the washing machine,
the panel and error message is automatically recognized and the error type and
countermeasures are displayed on the smart phone.

7. Ifthe smartphone fails to recognize the error code more than twice, please enter the error
code displayed on the display panel of the washer manually into the Smart Care app.

_ Downloading the Smart Care

app

• Download the Samsung Laundry App into your mobile phone from the Android market
or Apple App store. (Search word : Samsung Smart Washer/Dryer}

_ Precautions when using Smart Care

Ifa lighting device (e.g. fluorescent or lamp) is reflected on the display panel of the

washing machine, the result on the display panel may not be recognized easily.

• Ifan error occurs more than twice, please manually enter the error code displayed on the

display panel of the washing machine into the Smart Care app.
Ifthe angle of the smartphone camera and the display panel of the washing machine is

incorrect, the error may not be recognized properly.
Please try to hold the smart phone at an angle to the display panel as shown by the

figure.

s

×tr-J _pin

/

Washing clothes using the cycle selector

Your new washing machine makes washing clothes easy, using Samsung's "Fuzzy Control"

automatic control system. When you select a wash program, the machine will set the correct
temperature, washing time, and washing speed.

1. Turn on your sink's water tap.

2. Press the Power button.

3. Open the door.

4. Load the articles of clothing one at a time loosely into the drum, without overfilling it.

5. Close the door.

6. Add detergent, softener, and pre-wash detergent (ifnecessary) into the appropriate
compartments.

Pre-wash is only available when selecting the NORMAL, DEEP STEAM, HEAVY DUTY,
BEDDING, SANITIZE, ALLERGEN, ACTIVE WEAR, PERM PRESS, TOWELS(Only for

WF42H5600A* model), ECO COLD(Only for WF42H5700A* model) cycles. It is only
necessary if your clothing is heavily soiled.

7. Use the Cycle Selector to select the appropriate cycle according to the type of material:
NORMAL,DEEP STEAM, HEAVY DUTY, BEDDING, SANITIZE, ALLERGEN, RINSE+SPIN,
ECO COLD(Only ForWF42H5700A* Model),QUICK WASH, TOWELS(ONLY FOR
WF42H5600A* MODEL),PERM PRESS, WOOL, DELICATES, ACTIVE WEAR. The relevant
indicators will illuminate on the control panel.

8. At this time, you can control the wash temperature, the number of rinse cycles, the spinning
speed, and the delay time by pressing the appropriate option button.

9. Press the Start/Pause button on the Cycle Selector and the wash will begin. The process
indicator will light up and the remaining time for the cycle will appear in the display.

Pause Option

1. Within 5 minutes of starting a wash, it is possible to add/remove laundry items to/from the
wash.

2. Press the Start/Pause button to unlock the door.

3. The door cannot be opened when the water is too HOT or the water level is too HIGH.

4. After closing the door, press the Start/Pause button to restart the wash.

When the cycle is finished:

After the total cycle has finished, the power will turn off automatically.

1. Open the door.

2. Remove laundry.

USING STEAM WASH

Ifyou select steam, the steam acts at the most effective times for the detected amount of laundry,
maximizing the effect of the steam, increasing the wash temperature, enhancing the Soak effect, and
improving wash performance.

1. Load the washer.

2. Press the Power button.

3. Turn the Cycle Selector and select a Steam Cycle. (The Deep Steam course automatically selects
Steam.)

4. Press the Steam button.

5. Add detergent to the dispenser tray and add fabric softener up to the marked line.

6. Press the Start/Pause button.
: The washer automatically selects the optimal wash conditions by sensing the weight of the laundry.

_ team may not necessarily be visible during the steam cycles. Steam may not be present during the

entire steam wash cycle.

ATC (AUTO TEMPERATURE CONTROL)

ATCis the control function that the washer controls watertemperaturewith temperaturesensor (thermistor).

_ ecause there are numerous water temperatures depending on the customer's environments ( cold

areas, warm areas, various water temperature, settings of heater temperature, etes), ATC function in
our washer maintains the certain level of wash temperature to output the best washing performance at
each cycle.

lf you select normal & heavy duty cycles, those courses are the regulation and UL cycles. Since new
washer must reduce the amount of energy usage at first priority, customers will notice more cold water

entering the washer. But This is Normal, not a problem.
In those regulation cycles, Hot temperature is similar to acceptable adult bath-water temperature and

_warm temperature is similar to comfortable swimming-pool water temperature.

Ifcustomers want to wash clothes in specific water temperature, customers should choose a different
cycles at each temperature (Hot/Warm/Eco Warm ).

DETERGENT USE

Your Washer is designed to use high efficiency (HE) detergents.

,, For best cleaning results, use a high efficiency detergents such as

Tide HE, Wisk HE, Cheer HE, or Gain HE*. High efficiency detergents
contain suds suppressors that reduce or eliminate suds. When fewer
suds are produced, the load tumbles more efficiently and cleaning is

maximized.

A Regular detergent is NOT recommended. Please use HE detergents

wAR'"_,,,only.

_ educing the amount of detergent may reduce the quality of cleaning. It is important to pre-treat

stains, sort carefully by color and soil level, and avoid overloading.
* Brand names are trademarks of their respective manufacturers.

FEATURES

Automatic dispenser

Your washer has separate compartments for dispensing

detergent and color-safe bleach, chlorine bleach, and
fabric softener. Add all laundry additives to their respective

compartments before starting your washer.

The automatic dispenser MUST ALWAYS be in place before
you start your washer.

DO NOT open the automatic dispenser when your washer is
running.

Usage Pointers:
,, Never exceed the manufacturer's recommendations when

adding detergent.

,, This compartment holds liquid detergent for the main wash

cycle, which the washer adds to the load at the beginning
of the cycle.

----4 Liquid Detergent

•......qPre wash

compartment

_ efore using powdered detergent, remove the Liquid

Detergent holder from the compartment. Powdered
detergent will not dispense from the Liquid Detergent

holder.

Detergent compartment

,, Pour the recommended amount of laundry detergent directly into the detergent compartment

before starting your washer.

Pre wash compartment

When using the Pre Wash option, add detergent to both the Pre Wash compartment and the
detergent compartment. The washer will automatically dispense the detergent during Pre Wash.

Ifyou use a high efficiency (HE) detergent, add 1/3 of the recommended amount to the Pre

Wash compartment and 2/3 of the recommended amount to the detergent compartment.

Bleach compartment

(Liquid chlorine bleach only)

1. Add chlorine bleach to the bleach compartment.
DO NOT exceed the MAX FILL line.

2. Avoid splashing or over-filling the compartment.

3. Your washer automatically dispenses bleach into the tub at
the appropriate time.

4. The dispenser automatically dilutes liquid chlorine bleach
before it reaches the wash load.

_* Never pour undiluted liquid chlorine bleach directly onto

the load or into the tub. It is a powerful chemical and
can cause fabric damage, such as weakening of the
fibers or color loss, if not used properly.

Oxi-type boosters or color-safe bleach can be added to
the drum prior to adding laundry.

Put the laundry into the drum only after confirming

that the oxi-type boosters or color-safe bleach has
completely entered the hole of the drum.

To use powdered detergent and powder oxi-type
boosters or powdered color-safe bleach at the same

time, it is more effective to put them in the drum
together before adding the laundry. When you use
powdered detergent, remember to remove the Liquid

Detergent holder from the detergent compartment.

Fabric Softener },,,-

compartment

Bleach },,,-

compartment

f LJ

Fabric softener compartment

1. Pour the recommended amount of liquid fabric softener into the softener compartment.
For smaller loads, use less than one capful.

2. Dilute the fabric softener with water until it reaches MAX FILL in the compartment.

3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse
cycle.

_ se the softener compartment ONLY for liquid fabric softeners.

DO NOT use a Downy Ball* in the Fabric softener compartment of this washer. It will not

be added at the appropriate time.

Use the detergent compartment.

* Brand names are trademarks of their respective manufacturers.

lf you overfill the detergent, bleach, or softener compartments, the contents of the
compartment will automatically be released into the washer. This could damage any

garments that are in the drum.

CLEANING THE EXTERIOR

Turn off the water faucets after finishing the day's washing.
This will shut off the water supply to your washer and prevent the unlikely possibility of damage from

escaping water. Leave the door open to allow the inside of your washer to dry out.

Use a soft cloth to wipe up all detergent, bleach or other spills as they occur.
Clean the following as recommended below:
Control Panel - Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray

cleaners directly on the panel.
Cabinet - Clean with soap and water.

CLEANING THE INTERIOR

Clean the interior of your washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial
residue that may remain in your washer as a result of washing clothes.

Failureto follow these instructions may result in unpleasant conditions, including odors and/or permanent
stains on your washer or laundry.

Hard water deposits may be removed, if needed. Use a cleaner labeled "Washer safe".

CLEANING THE DISPENSERS

You may need to clean the automatic dispenser periodically to remove
laundry additive buildup.

1. Pull out the Liquid Detergent holder from the detergent compartment.

2. Remove the siphon cap from the fabric softener and bleach

compartments.

3. Wash all of the parts under running water.

4. Clean the dispenser recess with a soft brush.

5. Reinsert the siphon cap and push itfirmly into place.

6. Push the Liquid Detergent holder back into place.

7. Run a Rinse+Spin cycle without any load in your washer.

i

Siphon

STORING YOUR WASHER

Washers can be damaged if water is not removed from hoses and internal components before storage.

Prepare your washer for storage as follows:

,, Select the Quick Wash cycle and add bleach to the automatic dispenser. Run your washer through the

cycle without a load.

,, Turn the water faucets off and disconnect the inlet hoses.

* Unplug your washer from the electrical outlet and leave your washer door open to let air circulate inside

the tumbler.

* Ifyou store your washer in below-freezing temperatures, make sure you allow time for any leftover water

in your washer to thaw before use.

CLEANING THE DEBRIS FILTER

We recommend cleaning the debris filter when water does not drain well or the "5E" error message is displayed.

1. Unplug the washing machine from the power supply. _

2. Open the filter cover using a coin or a key.

3. Holding the drain cap, pull the drain tube that step!
is hooked on the guide hook to the front. Do

not pull the drain tube with excessive force.

4. Place a bowl under the washing machine to
catch any remaining water. Then, hold the

drain tube with one hand, and turn the drain
cap counter clockwise with the other hand to

separate it from the drain tube.

5. Drain the remaining water completely. ,ramcap

6_

Turn the debris cap counterclockwise, and then pull
the debris cap and debris filter assembly out of the
washer.

/

Debris filter capl

7_

Wash any dirt or other material from the
debris filter. Make sure the drain pump
propeller behind the debris filter isnot

blocked.

8. When you have finished cleaning the filter, insert the debris
cap and filter assembly back into the washer. Turn the
debris filter cap clockwise until the indicator on the debris
filter cap is in the 12 o'clock position, pointing to the

indicator on the washer.

9. Re-attach the emergency drain cap to the drain tube, and
then hook the tube to the hook guide.

10. Re-install the filter cover.

_7} For models with the safety filter cap

• To open, push in, and then turn the safety fi ter 3aE
counterclockwise. The spring in the cap w maKe
opening the cap easy

• To close, turn the safety fi Iter cap ClOCKWISe.AS _ou
turn the cap, the spring will make a rattling sound The

rattling sound is normal.

Debris filter c_p _ Debrisfilter

CLEANING THE DOOR DIAPHRAGM

1. Open the washer door and remove any clothing or items from the washer.
Check if there are any breign substances on

the grey diaphragms (9 between the lid and the
drum.

Tocheck this, turn the diaphragm @ out.

3. If there are any foreign substances, remove them.

4. If you find stained areas, wipe them down using the procedure below:

a} Carefully combine s4cup (177 mL) of liquid chlorine bleach with 1 gal. (3.8 L) of warm

tap water.
b) Wipe the diaphragm area with the dilute solution using a damp cloth.
c) Let stand 5 minutes.

d} Wipe down the area thoroughly with a dry cloth and let the washer interior air dry with

the door open.

IMPORTANT:

Wear rubber gloves when cleaning for prolonged periods.
Refer to the bleach manufacturer's instructionsfor proper use.

PRESERVING THE TOP COVER AND THE FRONT FRAME

Do not place any heavy or sharp objects or a detergent box on the washing machine. They can scratch or

damage its top cover. Keep them in the pedestal (if purchased) or in a separate storage box.

Since the entire washing machine has a high-gloss finish, the surface can be scratched or damaged.
Avoid scratching or damaging the surface when using the washing machine.