SAMSUNG WF218AN User Manual
Washing Machine
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/global/register
WF218ANS
WF218ANB
WF218ANW
WF218ANS-02440D_EN.indd 1 2008-05-08 ¿ÀÈÄ 5:08:14
2_ Features of your new washer
features of your new washer
1. Extra Large Capacity
Even bulky garments and blankets get super clean. The large capacity leaves enough room
for a more thorough, cleaner wash.
2. Direct Drive Inverter Motor
The power to handle anything! Our direct-drive inverter motor delivers power right to the
washer tub from a variable speed, reversible motor. A beltless direct-drive motor generates
a higher spin speed of 1,150rpms for more effective, quiet operation. The washer also has
fewer moving parts.
3. Woolmark Certified
The machine wash wool cycle on the Samsung machines has been tested and passed the
required Woolmark Company specification for machine washable wool products. Fabrics
should be washed according to the instructions on the garment label as specified by
Woolmark and Samsung.
4. Pedestal with Storage Drawers (Model No : WE357A7W/S/R/L/G/
B)
An optional 15” pedestal is available to raise the washer for easier loading and unloading.
It also offers a built-in storage drawer that can hold a 100 oz. bottle of detergent
5. Stacking (Model No : SK-3A1/XAA , SK-4A/XAA , SK-5A/XAA)
Samsung washers and dryers can be stacked to maximize usable space. An optional
stacking kit is available for purchase from your Samsung retailer.
<Pedestal with Storage Drawers>
<Stacking>
WF218ANS-02440D_EN.indd 2 2008-05-08 ¿ÀÈÄ 5:08:14
Safety information _3
safety information
Congratulations on your new Samsung Washer. This manual contains important
information on the installation, use and care of your appliance. Please take time
to read this manual to take full advantage of your Washer’s many benefits and
features.
WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions in this manual do not cover all possible conditions and
situations that may occur. It is your responsibility to use common sense, caution, and care when installing,
maintaining, and operating your Washer.
IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS
WARNING
Hazards or unsafe practices that may result in severe personal injury or
death.
CAUTION
Hazards or unsafe practices that may result in minor personal injury or
property damage.
CAUTION
To reduce the risk of fire, explosion, electric shock, or personal injury when
using your washer, follow these basic safety precautions:
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions explicity.
Unplug the pwer plug from the wall socket.
Make sure the machine is grounded to prevent electric shock.
Call the service center for help.
Read all instructions before using the appliance.
With any equipment using electricity and moving parts, potential hazards exist.
To safely operate this appliance, become familiar with its operation and be careful when
using it.
Install and store your washer inside, away from exposure to weather.
Install and level your washer on a floor that can support its weight.
Your washer must be properly grounded. Never plug it into an ungrounded outlet. See page
7 for more information on grounding your washer.
WF218ANS-02440D_EN.indd 3 2008-05-08 ¿ÀÈÄ 5:08:14
4_ Safety information
To reduce the risk of fire or explosion:
• Do not wash items that have been washed, soaked, or treated with gasoline, dry
cleaning solvents, or other flammable or explosive substances. They give off vapors that
could ignite or explode. Rinse by hand any material that has been exposed to cleaning
solvent or other flammable liquids or solids before putting in your washer. Be sure that
all traces of such liquids, solids, and fumes have been removed. Dangerous substances
include acetone, denatured alcohol, gasoline, kerosene, certain liquid household
cleaners and spot removers, turpentine, waxes, and wax removers.
• Do not put gasoline, dry cleaning solvents, or other flammable or explosive substances
into the washer.
• Under certain conditions, hydrogen gas may be produced in a hot water system–such
as your hot water heater-- that has not been used for two weeks or more. HYDROGEN
GAS IS EXPLOSIVE. If your hot water system has not been used for two weeks or
more, turn on all hot water faucets in your home, and let the water flow for several
minutes before using your washer. This will release any hydrogen gas build–up. Since
hydrogen gas is flammable, do not smoke or light an open flame during this time.
Unplug the power cord before servicing your washer.
Do not reach into the appliance when the tumbler is moving.
Do not let children play on or in your washer. The washer door isn’t easily opened from the
inside, and a child could be seriously injured if trapped inside.
Do not tamper with the controls.
Do not repair, replace, or service any part of your washer yourself unless you fully
understand the recommended user–repair instructions and have the skills to carry them
out. Work done by an unauthorized person may void your warranty.
Store laundry detergents and other laundry supplies in a cool, dry place out of children’s
reach.
Do not wash or dry items that are soiled with vegetable or cooking oil. These items may
contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch
fire by itself.
Do not use chlorine bleach, ammonia, or acids (such as vinegar or rust remover) in the
same wash. Hazardous fumes can form.
Do not machine wash fiberglass materials. Small particles can stick to fabrics washed in
subsequent loads and cause skin irritation.
Before disposing of your washer, remove the door so that children or small animals cannot
get trapped inside.
Do not sit on top of your Washer.
Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically
for bulges, kinks, cuts, wear or leaks, and replace them every five years.
Ensure pockets are free from small irregularly shaped hard objects or foreign materials,
such as coins, knives, pins, etc. These objects could damage your washer.
Do not wash clothing with large buckles, buttons, or other heavy metal.
WARNING
WARNING
WARNING
CAUTION
WF218ANS-02440D_EN.indd 4 2008-05-08 ¿ÀÈÄ 5:08:15
Contents _5
contents
INSTALLING YOUR WASHER
6
6 Unpacking your washer
6 Overview of your washer
7 Electrica
l
7 Groundin
g
7 Wate
r
8 Drain facilit
y
8 Floorin
g
8 Location consideration
s
8 Alcove or closet installatio
n
9 Important note to installer
OPERATING INSTRUCTIONS
11
11 Loading your washer
11 Getting started
WASHING A LOAD OF LAUNDRY
12
12 Overview of the control panel
13 Child loc
k
13 Garment
+
14 Detergent use
14 Features
MAINTAINING YOUR WASHER
16
16 Cleaning the exterior
16 Cleaning the interior
16 Cleaning the dispensers
16 Storing your washer
17 Cleaning the debris filter
TROUBLESHOOTING
18
18 Check these points if your washer…
20 Information codes
APPENDIX
22
22 Fabric care chart
23 Helping the environment
23 Declaration of conformity
24 Specifications
25 Cycle chart
WF218ANS-02440D_EN.indd 5 2008-05-08 ¿ÀÈÄ 5:08:15
6_ Installing your washer
installing your washer
UNPACKING YOUR WASHER
Unpack your Washer and inspect it for shipping damage. Make sure you have received all of the items
shown below. If your Washer was damaged during shipping, or you do not have all of the items, contact
1-800-SAMSUNG(7267864).
OVERVIEW OF YOUR WASHER
( use for the Upper Bolt Hole )
Wrench Bolt hole covers Water Supply Hose
Hose guide Rubber Washers
Cold water supply hose
Hot water supply
hose
Drain Hose
Adjustable legs
Detergent drawer
Control panel
Door
WF218ANS-02440D_EN.indd 6 2008-05-08 ¿ÀÈÄ 5:08:17
Installing your washer _7
BASIC LOCATION REQUIREMENTS
Electrical
• 120 Volt 60 Hz 15 AMP fuse or circuit breaker
• Individual branch circuit serving only your Washer is recommended.
• Your Washer is equipped with a power cord.
NEVER USE AN EXTENSION CORD.
Grounding
ELECTRICAL GROUNDING IS REQUIRED ON THIS APPLIANCE.
This appliance must be grounded. In the event of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of least resistance for electric current.
This appliance is equipped with a power cord having a three-prong grounding plug for use in a
properly installed and grounded outlet.
Improper connection of the equipment-grounding conductor can result in a risk of electrical
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the
appliance is properly grounded. Do not modify the plug provided with the appliance – if it
does not fit the outlet, have a proper outlet installed by a qualified electrician.
IMPORTANT SAFETY PRECAUTIONS
• To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and
grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No.
70 Latest Revision and local codes and ordinances. It is the personal responsibility of the
appliance owner to provide adequate electrical service for this appliance.
NEVER CONNECT GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR HOT
WATER PIPES.
Water
To correctly fill your Washer in the proper amount of time, water pressure of 20 – 120 psi is
required.
Water pressure less than 20 psi may cause water valve failure, ,or may not allow the water valve
to shut off completely. Or, it may extend the fill time beyond what your Washer controls allow,
resulting in your Washer turning off. A time limit is built into the controls in the event of an internal
hose becoming loose and flooding your home.
The water faucets must be within 4 feet/122cm of the back of your Washer for the inlet hoses
provided with your Washer.
Accessory inlet hoses are available in various lengths up to 10 feet/305cm for faucets that
are further away from the back of your Washer.
To avoid the possibility of water damage:
• Have water faucets easily accessible
• Turn off faucets when the washer is not in use.
• Periodically check that there is no leakage from the water inlet hose fittings.
CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.
01 Installing your washer
CAUTION
CAUTION
WARNING
WARNING
WF218ANS-02440D_EN.indd 7 2008-05-08 ¿ÀÈÄ 5:08:17
8_ Installing your washer
Drain facility
The recommended height of the standpipe is 18 in/46 cm. The drain hose must be routed
through the drain hose clip to the standpipe. The standpipe must be large enough to accept the
outside diameter of the drain hose. The drain hose is attached at the factory.
Flooring
For best performance, your Washer must be installed on a solidly constructed floor. Wood floors
may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting
and soft tile surfaces are contributing factors in vibration and may cause your washer to move
slightly during the spin cycle.
Never install your washer on a platform or weakly supported structure.
Location considerations
Do not install your washer in areas where water may freeze, since your washer will always
maintain some water in its water valve, pump, and hose areas. This can cause damage the belts,
the pump, hoses and other components. Operating temperature should be above 60°F/16°C.
Alcove or closet installation
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides – 1 in / 25 mm
Rear – 4 in / 102 mm
Top – 17 in / 432 mm
Closet Front – 2 in / 51 mm
If the washer and dryer are installed together, the closet front must have at least 72 in² or 465
cm² of an unobstructed air opening. Your washer alone does not require a specific air opening.
installing your washer
WF218ANS-02440D_EN.indd 8 2008-05-08 ¿ÀÈÄ 5:08:17
Installing your washer _9
IMPORTANT NOTE TO INSTALLER
Please read the following instructions carefully before installing your Washer.
These instructions should be retained for future reference.
We recommend you hire a professional for installation of this washer.
STEP 1
Selecting a Location
Before you install your washer, make sure the location:
• Has a hard, level surface
• Is away from direct sunlight
• Has adequate ventilation
• Will not freeze (below 32°F or 0°C)
• Is away from heat sources such as oil or gas
• Has enough space so that your Washer need not stand on its power cord
• Doesn’t have any carpeting that will obstruct ventilation openings.
STEP 2
Removing the Shipping Bolts
Before using your Washer, you must remove the four
shipping bolts from the back of the unit.
1. Loosen all the bolts with the supplied wrench.
2. Slide the bolt and spacer up and remove the bolt with
the spacer through the hole in the rear wall of your
washer. Repeat for each bolt.
3. Fill the holes with the supplied plastic covers.
4. Keep the shipping bolts and spacers for future use.
STEP 3
Installing your Washer
1. Place the drain hose in the drain facility. Be
sure an airtight connection is NOT made
between the drain hose and the standpipe.
The standpipe must be at least 18 in or 46
cm high.
Caution must always be exercised to
avoid collapsing or damaging the drain
hose. For best results, the drain hose
should not be restricted in any way – by
elbows, couplings, or excessive lengths.
For situations where the drain hose
cannot be conveniently elevated to at
least 18 in or 46 cm, the drain hose must
be supported.
01 Installing your washer
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie strap
Laundry tub Stand pipe
WF218ANS-02440D_EN.indd 9 2008-05-08 ¿ÀÈÄ 5:08:18
10_ Installing your washer
2. Insert new rubber washer (supplied) into each end of the
inlet hoses. Firmly seat the washers in the couplings.
3. Check the inlet hose to ensure a washer is inside each fill
hose.
Thread the inlet hoses to the HOT and COLD faucet
connections.
On the other end of the hose, check for one rubber washer
per hose and install each fill hose to the water valve. Make
sure the hose with the Hot printed line is attached to the
HOT faucet. Tighten by hand until snug, then two-thirds of a
turn with pliers.
For correct water use, connect both HOT and COLD water
valves. If either or both are not connected, an “nF” (no fill)
error can occur.
4. Turn on the “HOT” and “COLD “water supply and check all
connections at the water valve and the faucet for leaks.
5. Plug the power cord into a 3-Prong, well grounded 120 volt
60 Hz approved electrical outlet protected by a 15-amp fuse
or comparable circuit breaker.
Your washer is grounded through the third prong of the
power cord when plugged into a three-prong grounded
receptacle.
6. Slide your washer into position.
7. Level your washer by turning the leveling legs in or out as
necessary by hand or the wrench included with your washer.
When your washer is level, tighten the nuts using the wrench
or (-) driver.
Your Washer must be leveled on all four sides. A carpenter’s
level should be used on all four corners of your Washer. It’s
a good idea after the first dozen washes to recheck your
washer’s levelness.
Avoid the damage to the legs, Do not
move the Washer unless the Lockingnuts are fastened to the bottom of the
Washer.
installing your washer
Cold Hot
Cold printed Hot printed
Rubber washer
WF218ANS-02440D_EN.indd 10 2008-05-08 ¿ÀÈÄ 5:08:22
Operating instructions _11
operating instructions
LOADING YOUR WASHER
• You can fill the tub with dry, unfolded clothes; but DO NOT OVERLOAD the tub.
• Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or
wrinkling of the load.
• Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle with similar
lightweight items.
• When washing big bulky items or a few smaller items that don’t fill the tub completely – a rug, a pillow,
stuffed toys, or one or two sweaters, for example – add a few towels to improve tumbling and spin
performance.
During the spin cycle, the washer may add additional water to redistribute the excessive unbalance
inside the drum.
• When washing heavily soiled loads, not overloading your Washer is very important to assure good
cleaning results.
• To add a forgotten item:
1. Press the Start/Pause Button.
2. Wait for the Door Lock light to go out (5 seconds)
3. Add the item, close the door, and press the Start/Pause Button.
After a 10-second pause, the cycle will resume.
To ensure thorough cleaning, add items within five minutes of starting the wash cycle.
GETTING STARTED
1. Load your Washer.
2. Close the door.
3. Add detergent and additives to the dispenser (see pages 15~16).
4. Select the appropriate cycle and options for the load (see pages 12~14).
5. Press the Start/Pause Button.
6. The Wash Indicator light will illuminate.
7. The estimated cycle time will appear in the display.
The time may fluctuate to better indicate the time remaining in the cycle.
The actual time required for a cycle may differ from the estimated time in the display depending on the
water pressure, water temperature, detergent, and laundry.
8. Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a
quick drain.
• When the cycle is complete, the Door Lock light will go out and “End” will appear in the display.
• DO NOT attempt to open the door until the Door Lock light is off. To add a forgotten item, see
“Loading your Washer” section. (page 11)
• When your Washer is restarted after a pause, expect a delay of up to 15 seconds before the cycle
continues.
• Pressing Power cancels the cycle and stops your washer.
• The Wash, Rinse and Spin indicator lights will illuminate during those portions of the cycle.
02 Operating instructions
WF218ANS-02440D_EN.indd 11 2008-05-08 ¿ÀÈÄ 5:08:22
12_ Washing a load of laundry
washing a load of laundry
OVERVIEW OF THE CONTROL PANEL
Digital graphic
display
Displays the remaining cycle time, all cycle information, and error messages.
Temperature
selection button
Press the button repeatedly to cycle through the different water temperature options.
Hot/Cold - Whites and heavily soiled, colorfast items.
Warm/Warm - Colorfast items. When warm rinse is selected, only the final rinse will
be warm.
The other rinses will be cold to conserve energy.
Warm/Cold - Moderately soiled, colorfast items; most wrinkle-free items.
Cold/Cold - Brightly colored, very lightly soiled items.
Spin selection
button
Press the button repeatedly to cycle through the different spin speed options.
High - Use for underwear, t-shirts, jeans and sturdy cottons.
Medium - Use for jeans, wrinkle-free or wash-and-wear items and synthetics.
Low - Use for delicate items needing a slow spin speed.
No Spin - Drains your Washer without spinning. Use for extremely delicate
items that cannot tolerate any spin.
Soil Level
selection button
Press the button to select the Soil Level/washing time.
Heavy - For heavily soiled loads.
Normal - For moderately soiled loads. This setting is best for most loads.
Light - For lightly soiled loads.
Signal selection
button
Press the button to increase or decrease the end of cycle signal volume or
turn off the signal.
Select Cycle
Option
Press these buttons to select different cycle options.
Delay Start - Any cycle can be delayed for up to 24 hours in one-hour
i
ncrements. Displayed hour indicates the time at which the wash will be started.
Extra Wash - Add additional time to the wash for better stain removal.
Extra Rinse - Add an additional rinse at the end of the cycle to more
thoroughly remove laundry additives and perfumes.
6
5
4
3
2
1
8
9
7
5
4
3
2
1
6
WF218ANS-02440D_EN.indd 12 2008-05-08 ¿ÀÈÄ 5:08:23
Washing a load of laundry _13
Cycle Selector
Select the appropriate cycle for the type of load.
This will determine the tumble pattern and spin speed for the cycle.
To minimize wrinkling of laundry, select the Perm Press cycle.
Heavy Duty - For sturdy, colorfast fabrics and heavily soiled garments.
Normal - For most fabrics including cottons, linens, and normally soiled garments.
Whites - For white fabrics with or without bleach.
Wool - For machine-washable wool. Loads should be under 8 pounds.
The wool wash cycle of this machine has been approved by
Woolmark for the washing of machine washable Woolmark
products provided that the products are washed according
to the instructions on the garment label and those issued by
the manufacturer of this washing machine, M0509.
Delicates - For sheer fabrics, bras, lingerie silk, and other handwash-only
fabrics. For best results, use liquid detergent.
Perm Press - For wash-and-wear, synthetic fabrics, and lightly to normally
soiled garments.
Towels - For bath towels, washcloths and mats.
Sanitize - For heavily soiled, colorfast garments. This cycle heats the water to
150°F to eliminate bacteria.
If Pause is selected during the heating portion of the Sanitize Cycle, your
Washer door will remain locked for your safety.
Spin Only - Provides a spin to remove more water.
Rinse + Spin - Use for loads that need rinsing only or to add rinse-added
fabric softener to a load.
Start/Pause
selection button
Press to pause and restart programs.
Power button
Press once to turn your washer on, press again to turn your washer off. If
the washer is left on for more than 10 minutes without any buttons being
touched, the power automatically turns off.
Child lock
A function that prevents children from playing with your washer.
ACTIVATING/DEACTIVATING
If you want to activate/deactivate the Child Lock function, press the Soil Level and Signal
buttons at the same time for 3 seconds.
How It Works:
1. “Child Lock” can be activated while your Washer is running.
2. Once you activate “Child Lock”, all controls (except for the Power button) will be locked
until you deactivate “Child Lock”.
3. The Child Lock button will be lit while it is in effect.
When buttons, other than the Power button, do not respond, please check if the “Child
Lock” function is on.
Garment+
You can add or take out laundry items even after the wash has started, as long as the
“Garment+” light is on. Pushing the Start/Pause button unlocks the door, unless the water is
too hot or if there is too much water in your Washer. If you are able to unlock the door and wish
to continue the wash cycle, close the door and press the
Start/Pause button.
03 Washing a load of laundry
7
8
9
WF218ANS-02440D_EN.indd 13 2008-05-08 ¿ÀÈÄ 5:08:24
14_ Washing a load of laundry
DETERGENT USE
Your Washer is designed to use high efficiency (HE) detergents.
• For best cleaning results, efficiency detergents such as Tide HE, Wisk
HE, Cheer HE or Gain HE*. High efficiency detergents contain suds
suppressors that reduce or eliminate suds. When fewer suds are
produced, the load tumbles more efficiently and cleaning is maximized.
Regular detergent is NOT recommended. Please use only HE
detergents.
Reducing the amount of detergent may reduce the quality of cleaning. It is important to pre–treat
stains, sort carefully by color and soil level, and avoid overloading.
* Brand names are trademarks of their respective manufacturers.
FEATURES
Automatic dispenser
Your Washer has separate compartments for dispensing
detergent and color-safe bleach, chlorine bleach, and fabric
softener. All laundry additives are added to their respective
compartments before starting your Washer.
The automatic dispenser MUST ALWAYS be in place before
starting your Washer.
DO NOT open the automatic dispenser when your Washer is
running.
To use:
1. Pull out the dispenser drawer on the left side of the control
panel.
2. Add recommended quantity of additive to the appropriate
compartments with laundry additives, and be careful not to
overfill or spill.
3. Slide the dispenser drawer carefully and completely back
into the compartment.
Detergent compartment
1. Pour the recommended amount of laundry detergent directly into the detergent compartment
before starting your Washer.
2. If color-safe bleach is to be used, it should be added with detergent to the detergent
compartment.
• When adding color-safe bleach with detergent, it is best if both laundry products are in
the same form – granular or liquid.
If using liquid detergent, lower the detergent selector and add the detergent to the
detergent compartment.
washing a load of laundry
WARNING
Detergent
selector
Detergent
compartment
WF218ANS-02440D_EN.indd 14 2008-05-08 ¿ÀÈÄ 5:08:25
Washing a load of laundry _15
Bleach compartment
(Liquid chlorine bleach only)
1. Add chlorine bleach to the bleach compartment.
DO NOT exceed the MAX FILL line.
2. Avoid splashing or over–filling the compartment.
3. Your Washer automatically dispenses bleach into the tub at
the appropriate time.
4. The dispenser automatically dilutes liquid chlorine bleach
before it reaches the wash load.
• Never pour undiluted liquid chlorine bleach directly
onto the load or into the tub. It is a powerful chemical
and can cause fabric damage, such as weakening of
the fibers or color loss, if not used properly.
• If you prefer to use color–safe, non–chlorine bleach,
add it to the appropriate detergent compartment.
DO NOT pour color–safe bleach into the Bleach
compartment.
Fabric softener compartment
1. Pour the recommended amount of liquid fabric softener into the softener compartment.
For smaller loads, use less than one capful.
2. Fabric softener should be diluted with water until it reaches MAX FILL in the compartment.
3. The dispenser automatically releases liquid fabric softener at the proper time during the rinse
cycle.
• Use the softener compartment ONLY for liquid fabric softeners.
• DO NOT use the Downy Ball* in Fabric softener Compartment with this Washer. It will
not add fabric softener at the appropriate time.
Use the detergent Compartment.
* Brand names are trademarks of their respective manufacturers.
03 Washing a load of laundry
Fabric Softener
compartment
Bleach
compartment
WF218ANS-02440D_EN.indd 15 2008-05-08 ¿ÀÈÄ 5:08:25
16_ Maintaining your washer
maintaining your washer
CLEANING THE EXTERIOR
Turn off the water faucets after finishing the day’s washing.
This will shut off the water supply to your Washer and prevent the unlikely possibility of damage from
escaping water. Leave the door open to allow the inside of your Washer to dry out.
Use a soft cloth to wipe up all detergent, bleach or other spills as they occur.
Clean the following as recommended:
Control Panel – Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray
cleaners directly on the panel.
Cabinet – Clean with soap and water.
CLEANING THE INTERIOR
Clean the interior of your Washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial
residue that may remain in your Washer as a result of washing clothes.
Failure to follow these instructions may result in unpleasant conditions, including odors and/or permanent
stains on your Washer or laundry.
Hard water deposits may be removed, if needed. Use a cleaner labeled “Washer safe”.
CLEANING THE DISPENSERS
The Automatic Dispenser may need to be cleaned periodically due to
laundry additive buildup.
1. Press the release lever on the inside of the dispenser and pull out.
2. Remove the Siphon Cap from the fabric softener and bleach
compartments.
3. Wash all of the parts under running water.
4. Clean the dispenser recess with a soft brush.
5. Reinsert the Siphon Cap, and push it firmly into place.
6. Push the dispenser back into place.
7. Run a Rinse & Spin cycle without any load in your Washer.
STORING YOUR WASHER
Washers can be damaged if water is not removed from hoses and internal components before storage.
Prepare your Washer for storage as follows:
• Select the Quick Wash cycle and add bleach to the automatic dispenser. Run your Washer through the
cycle without a load.
• Turn the water faucets off and disconnect the inlet hoses.
• Unplug your Washer from the electrical outlet and leave your Washer door open to let air circulate inside
the tumbler.
• If your Washer has been stored in below–freezing temperatures, allow time for any leftover water in your
Washer to thaw out before use.
1
2
Siphon cap
WF218ANS-02440D_EN.indd 16 2008-05-08 ¿ÀÈÄ 5:08:26
Maintaining your washer _17
CLEANING THE DEBRIS FILTER
We recommend cleaning the debris filter when water does not drain well or the “ND” error message is
displayed.
1. Open the filter cover by pressing and pulling the handle of
the filter cover with your finger.
2. Unscrew the drain cap by turning it counter-
clockwise.
3. Hold the cap on the end of the drain tube and
slowly pull it out about 6inches (15cm) and
drain off all the water.
4. Remove the debris filter cap.
5. Wash any dirt or other material from the debris filter. Make sure
the drain pump propeller behind the debris filter is not blocked.
6. Replace the debris filter cap.
7. Replace the filter cover
8. Close up the opening of drain tube with cap.
9. Don’t insert the drain tube in the hole
04 Maintaining your washer
Step 1 Step 2
WF218ANS-02440D_EN.indd 17 2008-05-08 ¿ÀÈÄ 5:08:29
Loading...