Samsung WA56H9000AW/A2-01, WA56H9000AW/A2-00, WA56H9000AP/A2-01, WA56H9000AP/A2-00 Owner’s Manual

\
tsng
user manual
Thank you for purchasing this Samsung product. To receive more complete service or accessory
parts, please register your product at or contact
www.samsung.com/register
1-800-SAMSUNG (726-7864)
OPERATING INSTRUCTIONS
10 Unpacking your washer 10 Overview of your washer 11 Basic location requirements
11 Electrical 11 Grounding
11 Water 12 Drain facility
12 Flooring 12 Location considerations 12 Alcove or closet installation
13 Required dimensions for Installation
13 Important note to installer 17 Loading your washer
17 Getting started
_1
WASHING A LOAD OF LAUNDRY
MAiNTAiNiNG YOUR WASHER
TROUBLESHOOTING
18 Overview of the control panel 20 Child Lock [@]
21 Sound 21 Garment Plus
21 My Cycle 21 Delay End 22 Pre Soak
22 AquaJet TM 22 Eco Plus
22 Mist Shower 22 Smart Care
23 Washing clothes using the cycle selector 23 ATC (Auto Temperature Control) 24 Detergent use
24 Features 27 Cleaning the exterior
27 Cleaning the interior 27 Storing your washer
27 Preserving the top cover and the front frame 28 Cleaning the dispensers
29 Self Clean 30 Check these solutions if your washer.,.
32 Information codes
APPENDIX 34
/ ii
35 36
36 36
English- 2
Fabric care chart Cycle chart
Helping the environment Declaration of conformity Specification
Congratulations on your new Samsung Washer. This manual contains important
information on the installation, use, and care of your appliance. Please take time
to read this manual to take full advantage of your washer's many benefits and features.
WHAT YOU NEED TO KNOW ABOUT SAFETY INSTRUCTIONS
Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your washer.
IMPORTANT SAFETY SYMBOLS AND PRECAUTIONS
What the icons and signs in this user manual mean:
Hazards or unsafe practices that may result in severe personal injury
/_ or death.
WARNING To reduce the risk of fire, explosion, electric shock, or personal injury
when using your washer, follow these basic safety precautions: Hazards or unsafe practices that may result in minor personal injury or
CAUTION property damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions explicitly.
Unplug the power plug from the wall socket.
Make sure the machine is grounded to prevent electric shock.
Call the service center for help.
Note
These warning icons are here to prevent injury to you and others. Please heed them explicitly.
After reading this section, keep it in a safe place for future reference. _Read all instructions before the
using appliance.
SAVE THESE INSTRUCTIONS
Engl sh - 3
_f tv nforrn _ton
J
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your
WARNINGappliance, follow basic precautions, including the following:
1. Read all instructions before using the appliance.
2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.
3. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.
4. Before the appliance is removed from service or discarded, remove the lid of the washing or drying compartment.
5. Do not reach into the appliance if the drum is moving.
6. Do not install or store this appliance where it will be exposed to the weather.
7. Do not tamper with the controls.
8. Do not repair or replace any part of the appliance or attempt any servicing unless it is specifically recommended in the user-maintenance instructions or in published user- repair instructions that you understand and have the skills to carry out.
9. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.
10. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the
hot water system has not been used for 2 weeks or more, before using a washer or combination washer-dryer, turn on all hot water faucets and let the water flow from
each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.
State of California Proposition 65 Warnings:
WARN_.GWARNING: This product contains chemicals known to the State of California to cause
cancer and reproductive toxicity.
SAVE THESE INSTRUCTIONS
Engl sh- 4
CRiTiCAL iNSTALLATiON WARNINGS
WARNING
Plug the power cord into an AC 120 V / 60 Hz/wall socket rated at 15 amps or higher. Use the socket for this appliance only. In addition, do not use an extension cord.
Sharing a wall socket with other appliances, using a power strip, or extending the power cord may result in electric shock or fire. Do not use an electric transformer. It may result in electric shock or fire. Ensure that the power voltage, frequency, and current match the product's
specifications. Failing to do so may result in electric shock or fire.
Have this appliance installed by a qualified technician or service company.
Failing to do so may result in electric shock, fire, an explosion, problems with the product, or injury.
Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis.
Unplug the power plug and clean it with a dry cloth. Failing to do so may result in electric shock or fire.
Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor.
Ifyou plug the power plug into the socket in the opposite direction, the electric wires within the cable may be damaged and this may result in electric shock or fire.
This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
Improper grounding may result in electric shock, fire, an explosion, or problems with the product.
Never plug the power cord into a socket that is not grounded correctly. Make sure the socket you use is grounded in accordance with local and national codes.
Do not install this appliance near a heater or flammable material.
G
Do not install this appliance in a humid, oily, or dusty location, or in a location exposed to direct sunlight or water (rain drops). Do not install this appliance in a location where gas may leak.
This may result in electric shock or fire.
Plug the power plug into the wall socket firmly. Do not use a damaged power plug, damaged power cord, or loose wall socket.
This may result in electric shock or fire.
Do not pull or excessively bend the power cord. Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a heavy object on the power cord, insert the power cord between objects, or push the power cord into the space behind the appliance.
This may result in electric shock or fire.
Do not pull the power cord when unplugging the power plug.
Unplug the power plug by holding the plug. Failing to do so may result in electric shock or fire.
_lf the power plug or power cord are damaged, contact your nearest service center.
SAVE THESE INSTRUCTIONS
Engl sh - 5
J
INSTALLATION CAUTIONS
CAUTION
_ Position the appliance so that the power plug is easily accessible.
_ nplug the power plug when the appliance is not being used for long periods of time or
CRITICAL USAGE WARNINGS
WARNING
Failing to do so may result in electric shock or fire due to electric leakage.
Install your appliance on a level and hard floor that can support its weight.
Failing to do so may result in abnormal vibrations, noise, or problems with the product.
during a thunder/lightning storm.
Failing to do so may result in electric shock or fire.
If the appliance is flooded, cut the power immediately and contact your nearest service center.
If the appliance emits a strange noise, a burning smell, or smoke, unplug the power plug immediately and contact your nearest service center.
Failing to do so may result in electric shock or fire.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate the area immediately. Do not turn any appliance or light on or off.
Do not use a ventilating fan.
A spark may result in an explosion or fire.
Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or other flammable or explosive substances.
This may result in electric shock, fire, or an explosion.
Do not force the washer lid open while the washer is operating (high-temperature washing/ drying/spinning).
Water flowing out of the washer may cause burns or cause the floor to be slippery. This may result in injury.
Forcing the lid open can damage the product or cause injury.
Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the washer before using it.
Do not insert your hand under the washer.
This may result in injury.
SAVE THESE INSTRUCTIONS
Engl sh- 6
_Do not power plug wet
touch the with hands.
This may result in electric shock.
Do not turn the appliance off by unplugging the power plug while the washer is in operation.
Plugging the power plug into the wall socket again may cause a spark and result in electric shock or fire.
Keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children.
If a child places a bag over their head, the child may suffocate.
Do not let children or infirm persons use this washer unsupervised.
Failing to do so may result in electric shock, burns or injury.
Do not insert your hand or a metal object under the washer while it is operating.
This may result in injury.
Do not attempt to repair, disassemble, or modify the appliance yourself.
Do not use any fuse (such as copper, steel wire, etc.) other than the standard fuse. Ifyou need to repair or reinstall the appliance, contact your nearest service center. Failing to do so may result in electric shock, fire, problems with the product, or injury.
lf any foreign substance such as water enters the appliance in any area other than the tub, unplug the power plug and contact your nearest service center.
Failing to do so may result in electric shock or fire.
Ifthe water supply hose comes loose from the faucet and floods the appliance, unplug the power plug.
Failing to do so may result in electric shock or fire.
USAGE CAUTIONS
CAUTION
lf the washer is contaminated by a foreign substance such as detergent, dirt, food waste, etc., unplug the power plug and clean the washer using a damp, soft cloth.
The clear portion of the lid can be broken by a strong impact. Take care when using the
- If the clear portion is cracked or broken, it may result in injury.
After a water supply failure or when reconnecting the water supply hose, open the faucet
slowly. Open the faucet slowly after a long period of non-use.
Ifa drain error occurs during an operation, check if there is a draining problem.
Do not insert your hand under the washer.
Failing to do so may result in discoloration, deformation, damage or rust.
washer.
The air pressure in the water supply hose or the water pipe may result in damage to a part or in water leakage.
If the washer is used when it is flooded because of a draining problem, it may result in electric shock or fire due to electric leakage.
This may result in injury.
SAVE THESE INSTRUCTIONS
Engl sh- 7
J
Insert the laundry into the washer completely so that laundry does not get caught in the lid.
Iflaundry gets caught in the lid, it may result in damage to the laundry or the washer, or
result in water leakage.
Ensure that the faucet is turned off when the washer is not being used.
Ensure that the water supply hose connectors are properly tightened. Failing to do so may result in property damage or injury.
Open the faucet and check if the water supply hose connector is firmly tightened and that there is no water leaking before using the product.
Ifthe water supply hose connectors are loose, it may result in water leakage.
Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
This may result in electric shock, fire, problems with the product, or injury.
Do not operate the appliance with wet hands.
This may result in electric shock.
Do not spray volatile material such as insecticide onto the surface of the appliance.
As well as being harmful to humans, it may also result in electric shock, fire, or problems with the product.
Do not place an object that generates a electromagnetic field near the washer.
This may result in injury due to a malfunction.
Since the water drained during a high-temperature wash or drying cycle is hot, do not touch the water.
This may result in burns or injury.
For waterproof fabrics, only use the WATERPROOF cycle.
Do not use other cycles for waterproof fabrics.
* This may result in injury or damage to the washer, walls, floor, or clothing due to
abnormal vibrations.
Set the temperature and spin according to the attached care label.
Do not operate the washer when the detergent dispenser is removed.
This may result in electric shock or injury due to water leakage.
Do not insert your hand into the detergent dispenser after opening it.
This may result in injury as your hand may be caught.
SAVE THESE INSTRUCTIONS
Engl sh- 8
Do not place any non-laundry objects, such as shoes, food waste, or animals into the washer.
This can cause abnormal vibrations that can damage the washer, and, in the case of pets, cause severe injury or death.
Do not press the buttons using sharp objects such as pins, knifes, fingernails, etc.
This may result in electric shock or injury.
Do not wash laundry contaminated by oils, creams, or lotions usually found in skincare shops or massage clinics.
This may result in the rubber seal becoming deformed and water leakage.
Do not leave metal objects (safety pins, hair pins, etc.) or bleach in the tub for long periods of time.
This may cause the tub to rust. If rust appears on the surface of the tub, apply a neutral cleansing agent to the surface and use a sponge to clean it. Never use a metal brush.
Do not use dry cleaning detergent directly in the tub and do not wash, rinse, or spin laundry contaminated by dry cleaning detergent.
This may result in spontaneous combustion or ignition due to heat from the oxidation of the oil.
Do not use hot water from water cooling/heating devices.
This may result in problems with the washer.
Do not use natural hand-washing soap in the washer.
If it hardens and accumulates inside the washer, it may cause problems with the product, discoloration, rust, or bad odors.
Do not wash large laundry items such as bedding in the washing net.
Failing to do so may result in injury due to abnormal vibrations. Place smaller items, such as lace socks and lingerie in the washing net.
Do not use hardened detergent.
If it accumulates inside the washer, it may result in water leakage.
Do not wash throw rugs or doormats.
Ifyou wash throw rugs or doormats, the sand will accumulate inside the washer. It may result in error such as no draining.
CRITICAL CLEANING INSTRUCTIONS
WARNING
Do not clean the appliance by spraying water directly onto it.
Q
Do not use the strong acid cleaning agent. Do not use benzene, paint thinner, or alcohol to clean the appliance.
This may result in discoloration, deformation, damage, electric shock, or fire.
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
Failing to do so may result in electric shock or fire.
SAVE THESE INSTRUCTIONS
Engl sh - 9
UNPACKING YOUR WASHER
Unpack your washer and inspect it for shipping damage. Make sure you have received all the items shown below. If your washer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (1-800-726-7864).
To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.
/_ Packing materials can be dangerous to children; Keep all packing material (plastic bags, polystyrene,
....... etc.) well out of children's reach.
/_ When unpacking the washing machine, 2 person collaboration is needed. To remove the cushion
....... bottom of the packing materials, forward dumping is strictly prohibited.
OVERVIEW OF YOUR WASHER
Drain Hose -- Control panel
Lid
Hose guide User manual hook Pmasticzip hose tie Water intake cap
Water suppmy hoses
Tools needed
Wrench Flat screwdriver Level
--_ Adjustable legs
o o o_1
Engl sh - 10
BASIC LOCATION REQUIREMENTS
Electrical
120 Volt 60 Hz 15 AMP fuse or circuit breaker. Individual branch circuit serving only your Washer is recommended.
Your Washer is equipped with a power cord.
Z_ NEVER USE AN EXTENSION CORD.
CAUTION
Grounding
ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE,
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.
This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly installed and grounded outlet.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
An improperly connected equipment-grounding conductor can increase the risk of electrical
....... shock. Check with a qualified electrician or serviceman if you are not sure whether the
appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.
IMPORTANT SAFETY PRECAUTIONS
To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No.
70 Latest Revision and local codes and ordinances. It is the personal responsibility of the
appliance owner to provide adequate electrical service for this appliance.
/_ NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR
....... HOT WATER PIPES.
Water
To correctly fill your Washer in the proper amount of time, water pressure of 20 to 116psi (137 to 800kPa) is required.
Water pressure less than 20 psi may cause water valve failure, or may not allow the water valve to shut off completely, or may extend the fill time beyond what your Washer controls allow,
causing your Washer to turn off. A time limit is built into the controls to prevent flooding in your home if a hose becomes loose.
The water faucets must be within 4 feet / 122 cm to the back of your Washer to match the inlet hoses provided with your Washer.
Accessory inlet hoses are available in various lengths up to 10 feet / 275 cm for faucets that are further away from the back of your Washer.
To avoid the possibility of water damage:
,, Have water faucets easily accessible ,, Turn off faucets when the washer is not in use.
,, Periodically check that there is no leakage from the water inlet hose fittings.
CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.
WARNING
Engl sh - 11
Drain facility
The recommended height of the standpipe is 39 in / 99 cm. The drain hose must be routed through the drain hose clip to the standpipe. The standpipe must be large enough to accept the
outside diameter of the drain hose. The drain hose is attached to the washer at the factory.
Flooring
For best performance, you must install your washer on a solidly constructed floor. Wood floors may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting
and soft tile surfaces are contributing factors to vibration which can cause your washer to move slightly during the spin cycle.
Never install your washer on a platform or weakly supported structure.
Location considerations
Do not install your washer in areas where water may freeze, since your washer will always retain some water in its water valve, pump, and hose areas. Frozen water can damage the belts, the pump, hoses, and other components.
Alcove or closet installation
MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:
Sides - 1 in / 25 mm Closet Front - 2 in / 51 mm Rear- 6 in / 152 mm TOP- 21 in/ 533 mm
Gap between end of water valve and the wall
- Case 1. Assemble supply hose after installing : Over 3.9 in (10 cm).
- Case 2. Assemble supply hose before installing :Over 2.8 in (7cm). If the washer and dryer are installed together, the closet front must have at least a 72 in2 (465 cm2)
unobstructed air opening. Your washer alone does not require a specific air opening.
A
in.
(2,,_ :m)
..................................... J
li.. 30.0io.-- 1F- 30.0io. 1i..
(2.5cm) (76.2cm) (76.2cm) (2.5cm)
A. Recessed area B. Side view - closet or confined area
Engl sh - 12
B
21i°.T iiiiiiii
/53.3om _ Jiiiiiiiil
j!!caso, 39io,,ooo
2in. ---_--- 32.3 in. --_1_-6 in.
(5.1cm) (82.0cm) (15.2cm)
Required dimensions for Installation
-4[ 44.!in. (114.0cm)
39.2in. I
44.9in.
(114.0cm)
30.0 in.
(76.2cm)
58.7in.
149.0cm)
_._ 32.3in.
(82.0cm)
: !*_ 3,0
Closetor Door"_
*Required spacing
IMPORTANT NOTE TO INSTALLER
Please read the following instructions carefully before installing your washer.
These instructions should be retained for future reference. We recommend you hire a professional to install this washer.
Installation Flow chart
!r 3in.
_- (7.6cm)
-- ¥ (7.6cm)
No
Yes
_steps.
STEP 1 Selecting a Location
[_ Before you install the washer, make sure the location:
Has a hard, level surface without carpeting or flooring that may obstruct ventilation.
Isaway from direct sunlight.
Has adequate ventilation.
Is not exposed to freezing temperatures (temperatures under 32 °F or 0 °C).
Isaway from heat sources such as oil or gas.
Has enough space so that the washer doesn't rest on its power cord.
Engl sh- 13
STEP2 Connectingthewaterandthedrain
Connecting the water supply hose
Z_ Before installing the water supply hoses, make sure there are
....... rubber gaskets inside the fittings at both ends of each new
water hose. Installing the water supply hoses without rubber gaskets can cause water leakage.
Z_ When you initially install the washer, be sure to use new hoses.
....... Failing to do so may result in a water leakage or overflow and
may damage your property.
z_Do not connect multiple water supply hoses together to
....... increase the length of the supply hose. Hoses connected this
way can leak and the leakage can cause electrical shock. If a hose is too short, replace the hose with a longer, high pressure
hose.
1. Connect the ends of the water supply hoses to the HOT and COLD faucets.
2. Tighten the fittings by hand until they are snug, and then tighten them an additional two-thirds of a turn with a wrench.
When you fasten the fittings, do not fasten them too tightly or apply
....... tape or sealant to the faucets or water supply intakes. This can
damage the fittings. After you have connected the water supply hoses to the faucets,
ensure that they are connected correctly by pulling the water supply hoses downwards
3. Place the unconnected ends of the hoses into a bucket and open the faucets connected to the two water supply hoses for 10 or 15 seconds to remove any foreign substances from the hoses. Close the
faucets before continuing.
4. Connect the ends of the water supply hoses to the water supply
intake connections at the back of the washer.
Z_ The water supply hose connected to the HOT faucet must be
....... connected to the hot water supply intake and the water hose
connected to the COLD faucet must be connected to the COLD water supply intake.
5. Tighten the fittings by hand until they are snug, and then tighten them an additional two-thirds of a turn with a wrench.
CoLd
_rWasher
Hot
To ensure the correct water usage, connect both the HOT and COLD water faucets. Ifeither or both are not connected, an
"4E" (no fill) error can occur. If you do not want to use the HOT water supply hose, insert
the water intake cap into the HOT water supply intake hole. In this case, you must select the Tap Cold option for the water temperature. If you select the Tap Cold option, all the lamps for the water temperature options are turned off.
Z_ Confirm that the water supply hoses are not twisted or bent. If
....... the hoses are twisted or bent, the hoses can leak and cause
electric shock due to the water leakage.
6. Turn on the HOT and COLD water supplies and check all the water supply intake connections and the faucets for water leaks.
Engl sh - 14
Connectingthedrainhose
The end of the drain hose can be positioned in
three ways: Over the edge of a wash basin
Secure the guide to the side of the basin wall with a hook or to the tap with a piece of string to prevent the drain hose from moving.
In a standpipe or laundry tub
The standpipe must be no shorter than 39 in (99
cm) and no longer than 96 in (245 cm).
Make sure that the connection between the drain hose and the standpipe is not airtight.
_ onnect the hose guide within 4 in (10cm)
from the end of the drain hose. If the drain hose is
96
39 _ ag"Min
extended more than 4 in (10cm) beyond the end of the _ hose guide, mold or microorganisms could spread to the inside of the washer.
The Drain Hose can be installed to a 96 in (245cm)
maximum, but the draining capability can be reduced at this height. Itcan cause the washer to have an odor because of remaining water in the drain system.
lf the drain hose is installed below 39 in (99cm), water can be drained in cycles due to a siphon phenomenon. It
causes the washer to display a "4E" error code.
Laundry tub Standpipe
No more than
4 in (10cm) _
etainer
Hose
Tie )
strap
Hose Guide
STEP 3 Leveling your washer
See if the washer is level by checking the position of the tub:
1. Slide the washer into position.
2. Open the lid of the washer, and pour the water into the tub to just below the pulsator level.
3,
If the washer is level, the pulsator is positioned at the center of the water as shown in the figure. Ifnot, level your washer by turning the front leveling feet clockwise or counterclockwise as necessary.
Turn the front leveling feet clockwise to raise the washer, and counterclockwise to lower the washer.
Engl sh- 15
Adjustable legs
(three)
STEP4
Poweringyourwasher
Plug the power cord into a 3-prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or
comparable circuit breaker. Your washer is grounded through the third prong of the power
cord when plugged into a three-prong grounded electrical outlet.
Test run Make sure that you install your washing machine correctly by running the Rinse+Spin cycle
after the installation is complete.
STEP 5
Running a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1. Load about 6 pounds of laundry into the tub.
2. Press the Power button to turn on your washer.
3. Select the Rinse+Spin cycle by turning the Cycle Selector.
4. Press the Start/Pause button to start the test cycle.
5. The washer should not rock or vibrate excessively when water is supplied or when washing or spinning, and should drain well during the spin cycle.
lf water leaks while water is being supplied or drained, check the water connections. Refer to the "Connecting the water and the drain" section on pages 14-15 for instructions.
lf the washer rocks and vibrates excessively, level your washer again. Refer to the "Leveling your washer" section on page 15 for instructions.
STEP 6 Calibration Mode
Your Samsung washing machine detects the laundry weight automatically.
For more accurate weight detection, please run Calibration Mode after the installation.
To run Calibration Mode, follow these steps:
1. Remove laundry or any contents in the machine.
2. Press the Temp. and Delay End buttons more 3 seconds when the power is switched on.
3. Press the Start/Pause button to activate "Calibration Mode".
4. The spin drum rotates clockwise approximately 2 minute.
5. When "Calibration Mode" is finished, "End" appears on the display, and the machine automatically turns off. The washing machine is now ready for use.
Engl sh - 16
c eratna n tnActon
I
_ WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance,
WARNINGfollow basic precautions, including the following:
LOADING YOUR WASHER
,, You can fill the tub with dry, unfolded clothes, but DO NOT OVERLOAD the tub any more than 3/4 full. ,, Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or
wrinkling of the load.
,, Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle with similar
lightweight items.
,, When washing big bulky items or a few smaller items that don't fill the tub completely - a rug, a pillow,
stuffed toys, or one or two sweaters, for example - add a few towels to improve spin performance.
,, Do not insert bulky items except for Bedding in this cycle.
During the spin cycle, the washer may add additional water to redistribute the clothes and correct an
imbalance inside the drum.
,, When washing heavily soiled loads, do not overload your washer to ensure good cleaning results. ,, To add a forgotten item:
1. Press the Start/Pause button to pause the washer.
2. Wait for the door to unlock automatically, and then open the door.
3. Add the item, close the door, and then press the Start/Pause button. The cycle will resume.
GETTING STARTED
1. Load your washer.
2. Add liquid (or powde0 detergent and additives to the dispenser (see pages 24-26).
3. Select the appropriate cycle and options for the load (see pages 18-23).
4. Close the lid.
5. Press the Start/Pause button.
6. The Wash Indicator light illuminates.
7. The estimated cycle time will appear in the display. The time may fluctuate to indicate the time remaining in the cycle.
The actual time required for a cycle may differ from the estimated time in the display depending on the water pressure, water temperature, detergent, and laundry.
8. Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a
quick drain.
@* When the cycle is complete, the Door Lock light will go out and "End" will appear in the display.
,, Pressing the Power button cancels the cycle and stops your washer. ,, The Wash, Rinse, and Spin indicator lights will illuminate during those portions of the cycle.
Engl sh - 17
OVERVIEW OF THE CONTROL PANEL
' *(Hold 3 sec)
HEAVY DUTY _ NIAGARA WASH
COLORS/DARKS/_ _-- WATERPROOF
SANITIZE _/'/ _-- BEDDING
PERM PRESS _k / _ DELJEATES
ACTIVE WEARX_ /--SPIN
DEEP STEAM ___-_ RINSE + SPIN
[] AquaJet''
Select the appropriate cycle br the type of load. The cycle you select determines the tumble pattern and spin speed
for the cycle.
To minimize wrinkling of laundry, select the Perm Press cycle.
NORMAL - For most fabrics including cottons, linens, and normally soiled garments.
HEAVY DUTY - For sturdy, colorfast fabrics and heavily soiled garments.
COLORS/DARKS - For brightly or dark colored casual garments. SANITIZE - For heavily soiled, colorfast garments. This cycle heats
the water to 150 °F to eliminate bacteria.
For heavily soiled, colorfast garments. (less than 141bs)
Ifyou select pause during the heating portion of the Sanitize Cycle, your
Washer door will remain locked for your safety.
*Drum Li{_ht *Sound L*Ehild Lock _ *Smart Care
When selecting this cycle, the water heats to an extra high temperature
to remove 99.9 _/oof certain bacteria typically found on clothing, bedding,
o
or towels. This certification is conducted by NSF International, an independent third-party testing and certification organization.
Please check the garment care label to avoid garment damage. Only sanitizing cycles have been designed to meet the requirements of this
protocol for sanitization efficacy.
_ NSF Protocol P172
Sanitization Performance of Residential and Commercial, Family-Sized Clothes Washers
ALLERGEN - This cycle is applied to remove dust mites, pet dander or other allergic substances of the fabric.
Only ALLERGEN cycle has been designed to meet the requirement of P351 for allergen reduction efficacy.
_S_ NSF Protocol P351
Allergen Reduction Performance of Residential and
Commercial, Family-Sized Clothes Washers
PERM PRESS - For wash-and-wear, synthetic fabrics, and lightly to normally soiled garments.
ACTIVE WEAR - Use this cycle to wash exercise wear such as sports jerseys, training pants, shirts/tops and other performance
clothing. This cycle provides effective soil removal with gentle action for special fabric care.
DEEP STEAM - For heavily soiled, colorfast garments, this cycle provides a high washing temperature and steam and is effective for cleaning stains.
Engl sh - 18
NIAGARA WASH - This cycle uses more water during the wash and rinse cycle for enhancing rinsing performance. For most fabrics including cottons, linens, and normally soiled garments.
WATERPROOF - For waterproof, water-resistant items.
Do not wash waterproof items and non-waterproof items together. For waterproof, water-resistant items. (less than 141bs)
BEDDING - For bulky items such as blankets and sheets. When you are washing comforters, use liquid detergent.
QUICK WASH - For lightly soiled garments needed quickly. It takes about 33 to 48 minutes accorfing to amount of laundry.
DELICATES - For sheer fabrics, bras, lingerie, silks, and other handwash-only fabrics. For best results, use liquid detergent.
SPIN - Drains the water and spins at a high speed. RINSE + SPIN - Use for loads that need rinsing only or to add rinse-added
fabric softener to a load. Provides instructions and diagnostics while keeping you updated on the cycle
status and time remaining. Pressthe button repeatedly to cycle through the different water temperature
options. Extra Hot - Heavilysoiled, colorfast items. Onlyavailablewith the Sanitizecycle. Hot - Whites and heavilysoiled, colorfast items.
Warm - Colorfast items. Eco Warm - Moderately soiled, colorfast items; most wrinkle-free items.
Cold - Brightly colored, very lightly soiled items. Tap Cold - Cold water with no warm water added.
Ifyou select the Tap Cold option, all the lamps for the water
temperature options are turned off.
Press the button repeatedly to cycle through the different spin speed options. Extra High - Removes more water from loads during spin. High - Use for underwear, t-shirts, jeans, and sturdy cottons. Medium - Use for jeans, wrinkle-free or wash-and-wear items, and
synthetics. Low - Use for delicate items needing a slow spin speed.
No Spin - Drains your washer without spinning. Use for extremely delicate items that cannot tolerate any spin.
Rinse Hold - No Drain and Spinning after Rinse.
Ifyou select Rinse Hold, all the lamps for the Spin options are turned off.
Press the button to select the soil level/washing time. (Light-} T" ÷ Normal-> ,L ÷ Heavy)
Heavy - For heavily soiled loads.
A
Normal - For moderately soiled loads. This setting is best for most loads.
T
Light - For lightly soiled loads. Press these buttons to select different cycle options.
AquaJet TM Deep Clean - Improve washing performance through longer AquaJet spray action. Water Level can be adjusted.
Extra Rinse - Change from spray rinse mode to deep rinse mode, and rinse once again.
Eco Plus - To increase your energy savings on your wash cycles. (Less hot water consumption)
Fabric Softener - Add an additional rinse at the end of the cycle to more thoroughly remove laundry additives and perfumes.
My Cycle - Press and hold for 3 seconds to Save. Create and/or use a cycle
you create with customized temperature, spin, soil level, option, etc.
Delay End - Delay the End of any cycle for up to 19 hours in one-hour increments. Displayed hour indicates the time the wash will be ended.
Self Clean - Use to clean dirt and bacteria from the drum. Regular use (after every 20 washes) is recommended. No detergent or bleach is needed.
Pre Soak - Remove stains more thoroughly by specifying additional time. Press to pause and restart cycles.
Press once to turn your washer on. Press again to turn your washer off. If the washer is left on for more than 10 minutes without any buttons being
touched, the power automatically turns off.
Engiish- 19
\
Child Lock [@]
Child Lock prevents children from playing with your washer.
Activating the Child Lock function
Press and hold the Spin and Soil Level buttons simultaneously for approximately 3 seconds.
When you activate the Child Lock function, the "Child Lock [@]" lamp blinks.
Using the Child Lock function
Ifthe lid isopened when the Child Lock function ison, "dE" is displayed and an alarm sounds.
Ifthe water level in the tub is above the safe water level, "dE" is displayed on the LED display
and the washing machine starts to drain water by force after 30 seconds.
Ifthe water level in the tub is above the safe water level and the Child Lock function is turned
on while the door is open, "CL" is displayed on the LED display even if the power of the washing machine is turned off and the washing machine drains water by force.
Even if the power of the washing machine is turned off, if the lid is opened while the water
level in the tub is above the Reset water level, "CL" is displayed on the LED display without the alarm sounding and the washing machine starts to drain water. When the draining operation finishes, the power is automatically turned off again.
You have activated the Child Lock function while the washing machine is running, the Start/
Pause button will not work. After the compulsory drain, the "CL" code display blinks at 1 second intervals and the
product enters the "CU' mode. (When the product is in the "CU' mode, only the Power
button works.) To cancel the "CL" mode, you need to turn the power off and then on again.
To cancel the "dE" mode, deactivate the Child Lock function. To deactivate the Child Lock function, press and hold the Spin and the Soil Level buttons simultaneously for at least
3 seconds.
Adding laundry when Child Lock is on
To add laundry, deactivate the Child Lock function. To deactivate the Child Lock
function, press and hold the Spin and the Soil Level buttons simultaneously for at least 3 seconds. See "Pause Option" on page 23 for additional details.
Deactivating the Child Lock function
Press and hold both the Spin and Soil Level buttons simultaneously for approximately
3 seconds.
When you deactivate the Child Lock function, the "Child Lock [@]" is turned off. The Child Lock function prevents children or the infirm from accidently operating the washer
and injuring themselves.
_ Ifa child enters the washing machine, the child may become trapped and suffocate.
WARNING
®
Once you have activated the Child Lock function, it continues working even if the power is turned off.
CAUTION
Forcing the lid open can result in injury or damage to the product.
To add laundry after you have activated the Child Lock function, you must first deactivate
the Child Lock function.
Engl sh - 20
Sound
The Sound Off function can be selected during all cycles.
Garment Plus _++
You can add or take out laundry items even after the wash has started, as long as the "Garment
Plus" light is on. Pushing the Start/Pause button unlocks the lid. If you open the lid and want to continue the wash cycle, close the lid, and then press the Start/Pause button.
lf you have activated Child Lock, you must deactivate it first. See page 20.
My Cycle
Letsyou save a custom wash cycle (temperature,spin, soil level,etc.) and then recall and use it with one button convenience.
Tosavea cycle and selected options asyour MyCycle,followthese steps:
1. Press the Power button.
2. Select a cycle using the Cycle Selector.
3. After cycle selection, set each option. See the "Cycle Chart" on page 35 for available option settings with each cycle.
4. Youcan then store the selected cycle and options by pressing and holding the My Cycle button
for longer than 3 seconds. The cycle and options you select will be displayed the next time you choose the My Cycle function.
5. Press the My Cycle button to load and use the saved My Cycle options. The "My Cycle" light will
indicate activation. Also, the chosen course and option lights will flicker.
You can change the My Cycle settings by repeating the process above. The last saved settings will be displayed the next time you choose the My Cycle function.
lf you press My Cycle and release it within 3 seconds, the previously saved cycle and options appear. If you press and hold My Cycle for 3 second or longer, the currently set cycle and
options are saved and the LED blinks for 3 seconds.
Delay End
You can set the washing machine to start your wash automatically at a latertime, by choosing a delay time.
The hour displayed indicates the time at which the wash will be ended.
1. Set your wash cycle.
2. Press the Delay End button repeatedly until the delay time is set.
3. Press the Start/Pause button. The "Delay End" indicator will be lit, and the clock will begin
counting down until it reaches the set time.
4. Tocancel a Delay End function, press the Power button and then turn the washing machine on
again.
Engl sh- 21
Pre Soak
Use this function when the laundry is heavily contaminated or stained. This function improves the wash performance by adding a Pre Soak cycle.
Ifyou select this function, the total cycle time is increased by 15 minutes. When the Pre Soak cycle starts, the washing machine repeats a wash cycle after supplying water and then performs a 15-minute soak cycle. When the Pre Soak cycle is complete, the configured wash cycle starts without draining
water.
AquaJet TM
Through the strong spray and detergent water recirculation produced by the Pump of AquaJet TM, wash can be more gentle and thorough than conventional top loads.
AquaJet TM Deep Clean: If AquaJet TM Deep Clean mode is selected, washing performance can be further improved by addition spray action. Sufficient water quantity can be ensured by adjusting Water Level.
NORMAL, HEAW DUTY, COLORS/DARKS, SANITIZE,
ALLERGEN, PERM PRESS, ACTIVE WEAR, DEEP STEAM,
NIAGARA WASH, RINSE+SPIN
WATERPROOF,BEDDING,QUICKWASH, DELICATES,SPIN NotAvailable
Available
Eco Plus
This function sets the temperature somewhat lower than the typical washing cycle and extends the wash time slightly. With laundry time slightly extended, it's possible to keep the same level of washing performance with cooler water. This function reduces energy consumption and
maintains the quality of the wash.
Mist Shower
Mist Shower sprays water from a nozzle that is independent of the main water supply system. It states that is soaks the laundry with
water from the beginning of the rinse cycle and ensures an effective .........
wash, but it's not part of the wash cycle, it's part of the rinse cycle, so this needs to state that it ensures an effective RINSE.
(If there are too many clothes, the Mist Shower does not work.)
Smart Care
This function enables you to check the status of the washing machine using a smartphone.
1. Toenable the Smart Care function, press and hold the Soil
Level key for 3 seconds after turning the power on or when an error occurs.
The error code history is deleted after you use this function.
2. The Smart Care indicator is lit on the display.
3. Run the Smart Care app on your smart phone.
GalaxyS, GalaxyS2, GalaxyS3, GalaxyS4, GalaxyS2(HD), Galaxy Note, Galaxy Note2, Galaxy Note3 (Other devices may not be normal operation).
Supported operating system: Android 2.2 or higher
IPhone 3 G S, iPhone 4/4S, iPhone 5/5S. Supported operating system : OS 4.3 or higher
4. Focus your smart phone's camera on the display panel of the washing machine.
5. If the smart phone's camera is focused on the display panel of the washing machine, the panel and error message is automatically recognized and the error type and countermeasures are displayed on the smart phone.
Engl sh - 22
6. If the smartphone fails to recognize the error code more than twice, please enter the error code displayed on the display panel of the washer manually into the Smart Care app.
_ Downloading the Smart Care
Download the Samsung Laundry App into your mobile phone from the Android market or Apple App store. (Search word : Samsung Smart Washer/Drye0
_ Precautions when Smart Care
Iflight from a light bulb, fluorescent bulb, or lamp is reflected on the display panel of
the washing machine, the smartphone may not be able to recognize the panel or error
message easily.
,, Ifyou hold the smartphone at too large an angle relative to the front of the display panel,
it may not be able to recognize the error code. For best results, hold the smartphone so
that the front of the panel and the smartphone are parallel or nearly parallel.
using
app
Washing clothes using the cycle selector
Your new washing machine makes washing clothes easy, using Samsung's "Fuzzy Control" automatic control system. When you select a wash program, the machine will set the correct temperature, washing time, and washing speed.
1. Press the Power button.
2. Open the lid.
3. Load the articles of clothing one at a time loosely into the drum, without overfilling it.
4. Add liquid (or powder) detergent, softener, and/or bleach (if necessary) to the appropriate compartments. See pages 24-26.
5. Close the lid.
6. Use the Cycle Selector to select the appropriate cycle according to the type of material:
NORMAL, HEAVY DUTY, COLORS/DARKS, SANITIZE, ALLERGEN, PERM PRESS, ACTIVE
WEAR, DEEP STEAM, NIAGARA WASH, WATERPROOF, BEDDING, QUICK WASH,
DELICATES, SPIN, and RINSE+SPIN. The relevant indicators will illuminate on the control panel.
7. At this time, you can control the wash temperature, the number of rinse cycles, the spinning speed, and the delay time by pressing the appropriate option button.
8. Press the Start/Pause button on the Cycle Selector and the wash will begin. The process
indicator will light up and the remaining time for the cycle will appear in the display.
Pause Option
To remove or add laundry items, follow these steps:
1. Press the Start/Pause button to unlock the lid. The lid cannot be opened when the water is too HOT.
2. Remove or add laundry items.
3. Close the lid, and then press the Start/Pause button to restart the wash. lf you have Child Lock on, you must deactivate it first. See page 21.
When the cycle is finished:
After the total cycle has finished, the power will turn off automatically.3
1. Open the lid.
2. Remove laundry.
ATC (AUTO TEMPERATURE CONTROL)
ATC is the control function that the washer controls water temperature with temperature sensor (thermistor). _ ecause there are numerous water temperatures depending on the customer's environments (cold
areas, warm areas, various water temperature, settings of heater temperature, etc.), ATC function in our washer maintains the certain level of wash temperature to output the best washing performance at each cycle.
lf you select normal & heavy duty cycles, those cycles are the regulation and UL cycles. Since new
washers must reduce the amount of energy usage as a first priority, customers will notice more cold water entering the washer. But, this is normal, not a problem.
ln those regulation cycles, Hot temperature is similar to acceptable adult bath-water temperature and
warm temperature is similar to comfortable swimming-pool water temperature.
Ifcustomers want to wash clothes in specific water temperatures, customers should choose a different
cycle at each temperature (Hot/Warm/Eco Warm).
Engl sh- 23
DETERGENT USE
Your washer is designed to use high efficiency (HE) detergents.
For the best cleaning results, use high efficiency detergents, such as Tide HE, Wisk HE, Cheer HE or Gain HE*. High efficiency detergents
contain suds suppressors that reduce or eliminate suds. When fewer suds are produced, the load tumbles more efficiently and cleaning is
maximized.
Z'_ Regular detergent is not recommended. Use HE detergents only.
WARNING
_ educing the amount of detergent may reduce the quality of cleaning. It is important to pre-treat
stains, sort carefully by color and soil level, and avoid overloading.
* Brand names are trademarks of their respective manufacturers.
FEATURES
Automatic dispenser
Your washer has separate compartments for dispensing detergent and color-safe bleach and fabric softener. Add all laundry additives to their respective compartments before starting your
Washer. The automatic dispenser MUST ALWAYS be in place before you start your washer.
DO NOTopen the automatic dispenser when your washer is running.
_, Never exceed the manufacturer's recommendations when adding detergent.
This compartment holds liquid detergent for the main wash cycle, which is added to the load at the beginning of the cycle.
When using powdered detergent, remove the liquid detergent compartment from the detergent drawer. The washer will not dispense powdered detergent from the liquid
detergent compartment.
To add detergent to the automatic dispenser:
1. Open the dispenser drawer.
2. Load the recommended amount of liquid (or powdeO detergent into the detergent compartment before you start your wash.
3. Close the drawer slowly and smoothly to avoid spilling, splashing, or premature dispensing of the contents.
lt is normal for a small amount of water to remain in the dispenser compartments at the end of the cycle.
Do not put chlorine bleach in the dispenser drawer.
Liquid detergent compartment
Engl sh - 24
Loading the Liquid (or Powder) detergent compartment
1o Pour the recommended amount of laundry detergent
directly into the detergent compartment before starting your washer.
2o If you are using color-safe bleach, add it with the detergent
to the detergent compartment.
When adding color-safe bleach with detergent, it is best if
both laundry products are in the same form - liquid.
When using powdered detergent, remove the liquid
detergent compartment from the detergent drawer. The washer will not dispense powdered detergent from the liquid detergent compartment.
Liquid detergent
compartment
Loading the Bleach compartment
(Liquid chlorine bleach only) 1, Add chlorine bleach to the bleach compartment.
DO NOT exceed the MAX FILL line.
_ void splashing or over-filling the compartment.
Your washer automatically dispenses bleach into the tub at the appropriate time.
2, The dispenser automatically dilutes liquid chlorine bleach
before it reaches the wash load.
Never pour undiluted liquid chlorine bleach directly onto the load or into the tub. It is a powerful chemical
and can cause fabric damage, such as weakening of the fibers or color loss, if not used properly.
Ifyou prefer to use color-safe, non-chlorine bleach, add it to the appropriate detergent compartment.
DO NOT pour color-safe bleach into the Bleach compartment.
Bleach
compartment
///,
//
/ //
En91sh- 25
Loading the Fabric softener compartment
1,
Pour the recommended amount of liquid fabric softener into the softener compartment.
For smaller loads, use less than one capful.
2,
Dilute the fabric softener with water until it reaches MAX FILL in the compartment.
3,
The dispenser automatically releases liquid fabric softener at the proper time during the rinse cycle.
®.
Use the softener compartment ONLY for liquid fabric
softeners.
®
DO NOT use the Downy Ball* in the fabric softener compartment with this washer. It will not add fabric softener at the appropriate time.
Use the detergent compartment.
Do not use liquid fabric softener that is too sticky as it may not mix with the water sufficiently.
* Brand names are trademarks of their respective manufacturers.
Fabric softener
En91sh - 26
Loading...
+ 60 hidden pages