Samsung WA52M7750AW/A4-00, WA52M7750AV/A4-00 Owner’s Manual

Washer
User manual
WA52M7750A*/ WA52M7755A*
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 1 2016-12-13  1:21:23
SAVE THESE INSTRUCTIONS
Safety information 4
What you need to know about the safety instructions 4 Important safety symbols 4 Important safety precautions 5
Contents
Installation 13
Unpacking your washer 13 Overview of your washer 14 Basic location requirements 16 Important note to installer 20 Step-by-step installation 20
Operating instructions 28
Loading your washer 28 Getting started 29
Washing a load of laundry 30
Control panel 30 Cycle overview 32 Options 34 Washing clothes using the cycle selector 38 ATC (Auto Temperature Control) 39 The basics 40 Detergent use 42 Features 43
Maintaining your washer 48
Cleaning the exterior 48 Cleaning the interior 48 Storing your washer 48 Preserving the top cover and the front frame 49 Cleaning mesh lter 49 Cleaning the dispensers 49 Self Clean 51
2 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 2 2016-12-13  1:21:23
SAVE THESE INSTRUCTIONS
Troubleshooting 52
Checkpoints 52 Information codes 56
Specications 60
Fabric care chart 60 Helping the environment 62 Declaration of conformity 62 Specication sheet 63 Cycle chart 64
Contents
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 3 2016-12-13  1:21:23
English 3
SAVE THESE INSTRUCTIONS
Safety information
Congratulations on your new Samsung washer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your washer’s many benets and features.
What you need to know about the safety instructions
Safety information
Please read this manual thoroughly to ensure that you know how to safely and efciently operate the extensive features and functions of your new appliance. Please store the manual in a safe location close to the appliance for future reference. Use this appliance only for its intended purpose as described in this instruction manual. Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution and care when installing, maintaining and operating your washer. Because the following operating instructions cover various models, the characteristics of your washer may differ slightly from those described in this manual and not all warning signs may be applicable. If you have any questions or concerns, contact your nearest service center or nd help and information online at www.samsung.com.
Important safety symbols
What the icons and signs in this user manual mean:
Hazards or unsafe practices that may result in severe personal injury, death and/or property damage.
Hazards or unsafe practices that may result in personal injury and/or property damage.
WARNING
CAUTION
NOTE
Indicates that a risk of personal injury or material damage exists.
4 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 4 2016-12-13  1:21:23
SAVE THESE INSTRUCTIONS
These warning signs are here to prevent injury to yourself and others. Please follow them explicitly. After reading this manual, store it in a safe place for future reference.
Read all instructions before using the appliance.
As with any equipment that uses electricity and moving parts, potential hazards exist. To safely operate this appliance, familiarize yourself with its operation and exercise care when using it.
WARNING
State of California Proposition 65 Warning (US only)
This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Important safety precautions
WARNING
To reduce the risk of re, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:
1. Read all instructions before using this appliance.
2. Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or
spotted with gasoline, dry-cleaning solvents, other ammable or explosive substances as they give off vapors that could ignite or explode.
3. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.
4. Before the appliance is removed from service or discarded, remove the lid of the washing or drying compartment.
5. Do not reach into the appliance if the drum is moving.
6. Do not install or store this appliance where it will be exposed to the weather.
7. Do not tamper with the controls.
8. Do not repair or replace any part of the appliance or attempt any servicing unless it is
specically recommended in the user-maintenance instructions or in published user­repair instructions that you understand and have the skills to carry out.
9. Do not add gasoline, dry-cleaning solvents, or other ammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.
Safety information
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 5 2016-12-13  1:21:23
English 5
SAVE THESE INSTRUCTIONS
Safety information
10. Under certain conditions, hydrogen gas may be produced in a hot water system that
Safety information
Critical installation warnings
Plug the power cord into an AC 120 V / 60 Hz/wall socket rated at 15 amps or higher. Use the socket for this appliance only. In addition, do not use an extension cord.
Sharing a wall socket with other appliances, using a power strip, or extending the power
Do not use an electric transformer. It may result in electric shock or re.
Ensure that the power voltage, frequency, and current match the product’s specications.
has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for 2 weeks or more, before using a washer or combination washer-dryer, turn on all hot water faucets and let the water ow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is ammable, do not smoke or use an open ame during this time.
WARNING
cord may result in electric shock or re.
Failing to do so may result in electric shock or re.
Have this appliance installed by a qualied technician or service company.
Failing to do so may result in electric shock, re, an explosion, problems with the product, or injury.
Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis.
Unplug the power plug and clean it with a dry cloth.
Failing to do so may result in electric shock or re.
Plug the power plug into the wall socket in the right direction so that the cord runs towards the oor.
If you plug the power plug into the socket in the opposite direction, the electric wires within the cable may be damaged and this may result in electric shock or re.
6 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 6 2016-12-13  1:21:23
SAVE THESE INSTRUCTIONS
This appliance must be properly grounded. Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
Improper grounding may result in electric shock, re, an explosion, or problems with the product.
Never plug the power cord into a socket that is not grounded correctly. Make sure the socket you use is grounded in accordance with local and national codes.
Safety information
Do not install this appliance near a heater or ammable material. Do not install this appliance in a humid, oily, or dusty location, or in a location exposed to direct sunlight or water (rain drops). Do not install this appliance in a location where gas may leak.
This may result in electric shock or re.
Plug the power plug into the wall socket rmly. Do not use a damaged power plug, damaged power cord, or loose wall socket.
This may result in electric shock or re.
Do not pull or excessively bend the power cord. Do not twist or tie the power cord. Do not hook the power cord over a metal object, place a heavy object on the power cord, insert the power cord between objects, or push the power cord into the space behind the appliance.
This may result in electric shock or re.
Do not pull the power cord when unplugging the power plug.
Unplug the power plug by holding the plug.
Failing to do so may result in electric shock or re.
If the power plug or power cord are damaged, contact your nearest service center.
Installation cautions
CAUTION
Position the appliance so that the power plug is easily accessible.
Failing to do so may result in electric shock or re due to electric leakage.
Install your appliance on a level and hard oor that can support its weight.
Failing to do so may result in abnormal vibrations, noise, or problems with the product.
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 7 2016-12-13  1:21:24
English 7
SAVE THESE INSTRUCTIONS
Safety information
Unplug the power plug when the appliance is not being used for long periods of time or during a thunder/lightning storm.
Failing to do so may result in electric shock or re.
Critical usage warnings
Safety information
If the appliance is ooded, cut the power immediately and contact your nearest service center.
If the appliance emits a strange noise, a burning smell, or smoke, unplug the power plug immediately and contact your nearest service center.
Failing to do so may result in electric shock or re.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate the area immediately. Do not turn any appliance or light on or off.
Do not use a ventilating fan.
A spark may result in an explosion or re.
WARNING
Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or other ammable or explosive substances.
This may result in electric shock, re, or an explosion.
Do not force the washer lid open while the washer is operating (high-temperature washing/ drying/spinning).
Water owing out of the washer may cause burns or cause the oor to be slippery. This may result in injury.
Forcing the lid open can damage the product or cause injury.
Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the washer before using it.
Do not insert your hand under the washer.
This may result in injury.
Do not touch the power plug with wet hands.
This may result in electric shock.
Do not turn the appliance off by unplugging the power plug while the washer is in operation.
8 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 8 2016-12-13  1:21:24
SAVE THESE INSTRUCTIONS
Plugging the power plug into the wall socket again may cause a spark and result in electric shock or re.
Keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children.
If a child places a bag over their head, the child may suffocate.
Do not let children or inrm persons use this washer unsupervised.
Failing to do so may result in electric shock, burns or injury.
Do not insert your hand or a metal object under the washer while it is operating.
This may result in injury.
Do not attempt to repair, disassemble, or modify the appliance yourself.
Do not use any fuse (such as copper, steel wire, etc.) other than the standard fuse.
If you need to repair or reinstall the appliance, contact your nearest service center.
Failing to do so may result in electric shock, re, problems with the product, or injury.
If any foreign substance such as water enters the appliance in any area other than the tub, unplug the power plug and contact your nearest service center.
Failing to do so may result in electric shock or re.
If the water supply hose comes loose from the faucet and oods the appliance, unplug the power plug.
Failing to do so may result in electric shock or re.
Safety information
Usage cautions
CAUTION
If the washer is contaminated by a foreign substance such as detergent, dirt, food waste, etc., unplug the power plug and clean the washer using a damp, soft cloth.
Failing to do so may result in discoloration, deformation, damage or rust.
The clear portion of the lid can be broken by a strong impact. Take care when using the washer.
If the clear portion is cracked or broken, it may result in injury.
After a water supply failure or when reconnecting the water supply hose, open the faucet slowly.
English 9
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 9 2016-12-13  1:21:24
SAVE THESE INSTRUCTIONS
Safety information
Open the faucet slowly after a long period of non-use.
The air pressure in the water supply hose or the water pipe may result in damage to a
If a drain error occurs during an operation, check if there is a draining problem.
If the washer is used when it is ooded because of a draining problem, it may result in
Safety information
Do not insert your hand under the washer.
This may result in injury.
Insert the laundry into the washer completely so that laundry does not get caught in the lid.
If laundry gets caught in the lid, it may result in damage to the laundry or the washer, or
Ensure that the faucet is turned off when the washer is not being used.
Ensure that the water supply hose connectors are properly tightened.
Failing to do so may result in property damage or injury.
Open the faucet and check if the water supply hose connector is rmly tightened and that there is no water leaking before using the product.
If the water supply hose connectors are loose, it may result in water leakage.
part or in water leakage.
electric shock or re due to electric leakage.
result in water leakage.
Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
This may result in electric shock, re, problems with the product, or injury.
Do not operate the appliance with wet hands.
This may result in electric shock.
Do not spray volatile material such as insecticide onto the surface of the appliance.
As well as being harmful to humans, it may also result in electric shock, re, or problems with the product.
Do not place an object that generates a electromagnetic eld near the washer.
This may result in injury due to a malfunction.
Since the water drained during a high-temperature wash or drying cycle is hot, do not touch the water.
This may result in burns or injury.
For waterproof fabrics, only use the WATERPROOF cycle.
10 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 10 2016-12-13  1:21:24
SAVE THESE INSTRUCTIONS
Do not use other cycles for waterproof fabrics. This may result in injury or damage to the washer, walls, oor, or clothing due to abnormal vibrations.
Set the temperature and spin according to the attached care label.
Do not operate the washer when the detergent dispenser is removed.
This may result in electric shock or injury due to water leakage.
Do not insert your hand into the detergent dispenser after opening it.
This may result in injury as your hand may be caught.
Do not place any non-laundry objects, such as shoes, food waste, or animals into the washer.
This can cause abnormal vibrations that can damage the washer, and, in the case of pets, cause severe injury or death.
Do not press the buttons using sharp objects such as pins, knifes, ngernails, etc.
This may result in electric shock or injury.
Do not wash laundry contaminated by oils, creams, or lotions usually found in skincare shops or massage clinics.
This may result in the rubber seal becoming deformed and water leakage.
Do not leave metal objects (safety pins, hair pins, etc.) or bleach in the tub for long periods of time.
This may cause the tub to rust.
If rust appears on the surface of the tub, apply a neutral cleansing agent to the surface
and use a sponge to clean it. Never use a metal brush.
Safety information
Do not use dry cleaning detergent directly in the tub and do not wash, rinse, or spin laundry contaminated by dry cleaning detergent.
This may result in spontaneous combustion or ignition due to heat from the oxidation of the oil.
Do not use hot water from water cooling/heating devices.
This may result in problems with the washer.
Do not use natural hand-washing soap in the washer.
If it hardens and accumulates inside the washer, it may cause problems with the product, discoloration, rust, or bad odors.
Do not wash large laundry items such as bedding in the washing net.
Failing to do so may result in injury due to abnormal vibrations.
English 11
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 11 2016-12-13  1:21:24
SAVE THESE INSTRUCTIONS
Safety information
Place smaller items, such as lace socks and lingerie in the washing net.
Do not use hardened detergent.
If it accumulates inside the washer, it may result in water leakage.
Do not wash throw rugs or doormats.
If you wash throw rugs or doormats, the sand will accumulate inside the washer. It may
Safety information
Critical cleaning warnings
Do not clean the appliance by spraying water directly onto it. Do not use the strong acid cleaning agent. Do not use benzene, paint thinner, or alcohol to clean the appliance.
This may result in discoloration, deformation, damage, electric shock, or re.
result in error such as no draining.
WARNING
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
Failing to do so may result in electric shock or re.
12 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 12 2016-12-13  1:21:24
Installation
Follow these instructions carefully to ensure proper installation of the washer and to prevent accidents when using it.
Unpacking your washer
Unpack your washer and inspect it for shipping damage. Make sure you have received all the items shown below. If your washer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (1-800-726-7864). To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.
WARNING
Packing materials can be dangerous to children; Keep all packing material (plastic bags, polystyrene, etc.) well out of children’s reach.
CAUTION
When unpacking the washer, 2 person collaboration is needed. To remove the cushion bottom of the packing materials, forward dumping is strictly prohibited.
Installation
When you lay the washer down to remove carton base, should protect the side of washer and lay it carefully. Never lay your washer on its back or front.
English 13
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 13 2016-12-13  1:21:24
Installation
Overview of your washer
Make sure all the parts are included in the product package. If you have a problem with the washer or the parts, contact a local Samsung customer center or the retailer.
01
02
Installation
03
04
05
06
08
10
11
12
09
07
14 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 14 2016-12-13  1:21:24
01 Drain hose 02 Hose guide 03 Lid
04 Built-in sink 05 Tub 06 Water Jet
07 Leveling feet 08 Water hose (Cold) 09 Water hose (Hot)
10 Control panel 11 Detergent drawer 12 Power cord
Parts supplied
Hose guide User manual Plastic zip hose tie Water intake cap
Parts not supplied
Water supply hoses
Installation
Tools needed for installation
Wrench Flat screwdriver Leveller
Adjustable Plier Measuring tape
NOTE
If you lose an accessory and want to purchase a replacement, contact the Samsung service center (1-800-SAMSUNG (1-800-726-7864)).
The design of the parts and accessories may differ from the pictures above. Their design is subject to change without notice for product improvement.
Do not reuse old hoses. Only use new water supply hoses when you install the washer. Old water supply hoses can leak or burst causing ooding and property damage.
Conrm that there are rubber washers inside each coupling of the water supply hoses.
English 15
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 15 2016-12-13  1:21:25
Installation
Basic location requirements
Installation
Electrical
120 Volt 60 Hz 15 AMP fuse or circuit breaker.
Individual branch circuit serving only your Washer is recommended.
Your washer is equipped with a power cord.
CAUTION
Never use an extension cord.
Grounding
Electrical grounding is required for this appliance.
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly installed and grounded outlet. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING
An improperly connected equipment­grounding conductor can increase the risk of electrical shock. Check with a qualied electrician or serviceman if you are not sure whether the appliance is properly grounded. Do not modify the plug provided with the appliance – if it does not t the outlet, have a proper outlet installed by a qualied electrician.
Important safety precautions
To prevent unnecessary risk of re, electrical shock or personal injury, all wiring and grounding must be done in accordance with the National Electrical Code ANSI/ FNPA, No.70 Latest Revision and local codes and ordinances. It is the personal responsibility of the appliance owner to provide adequate electrical service for this appliance.
CAUTION
Never connect the ground wire to plastic plumbing lines, gas lines, or hot water pipes.
Water
To correctly ll your Washer in the proper amount of time, water pressure of 20 to 116psi (137 to 800kPa) is required. Water pressure less than 20 psi may cause water valve failure, or may not allow the water valve to shut off completely, or may extend the ll time beyond what your Washer controls allow, causing your Washer to turn off. A time limit is built into the controls to prevent ooding in your home if a hose becomes loose.
16 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 16 2016-12-13  1:21:25
The water faucets must be within 4 feet (122 cm) to the back of your Washer to match the inlet hoses provided with your Washer.
NOTE
Accessory inlet hoses are available in various lengths up to 10 feet (275 cm) for faucets that are further away from the back of your washer. To avoid the possibility of water damage:
Have water faucets easily accessible.
Turn off faucets when the washer is not
in use.
Periodically check that there is no leakage from the water inlet hose ttings.
WARNING
Check all connections at the water valve and faucet for leaks
Drain facility
The recommended height of the standpipe is 39 in (99 cm). The drain hose must be routed through the drain hose clip to the standpipe. The standpipe must be large enough to accept the outside diameter of the drain hose. The drain hose is attached to the washer at the factory.
Never install your washer on a platform or weakly supported structure.
Location considerations
Do not install your washer in areas where water may freeze, since your washer will always retain some water in its water valve, pump, and hose areas. Frozen water can damage the belts, the pump, hoses, and other components.
Alcove or closet installation
Minimum clearances for closet and alcove installations:
Sides
Rear
1 in /
25 mm
6 in /
152 mm
If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²) unobstructed air opening. Your washer alone does not require a specic air opening.
Closet
front
Top
2 in /
51 mm
21 in /
533 mm
Installation
Flooring
For best performance, you must install your washer on a solidly constructed oor. Wood oors may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile surfaces are contributing factors to vibration which can cause your washer to move slightly during the spin cycle.
English 17
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 17 2016-12-13  1:21:25
Installation
Installation
Recessed area
A
A
B B
A 1 in (2.5 cm)
B 27.0 in (68.6 cm)
Side view - closet or conned area
A
A
B
C
E
D
A 21 in (53.3 cm)
B 2 in (5.1 cm)
C 29 7/16 in (74.4 cm)
18 English
D 6 in (15.2 cm)
Gap between end of water valve and the wall
Case 1. Assemble supply
E
hose after installing : Over 4 in (10 cm).
Case 2. Assemble supply hose before installing : Over 3 in (8 cm).
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 18 2016-12-13  1:21:25
Required dimensions for Installation
B
A
C
A 27.0 in (68.6 cm)
B 39.2 in (99.5 cm)
C 46.0 in (116.8 cm)
B
A
A 59.8 in (152.0 cm)
A
B
Installation
C
C
A* 48.0 in2 (310.0 cm2)
A
B* 24.0 in
2
(155.0 cm2)
C 3.0 in (7.6 cm)
A 29.3 in (74.4 cm)
B 46.0 in (116.8 cm)
NOTE
* Required spacing
English 19
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 19 2016-12-13  1:21:26
Installation
Installation
Important note to installer
Please read the following instructions carefully before installing your washer. These instructions should be retained for future reference. We recommend you hire a professional to install this washer.
Installation ow chart
Removing the
Selecting a
location
Running a test cycle
Run Rinse+Spin with
small amount of
laundry (about 4~5
towels) as a test cycle
shipping bolts (Front loading washers only)
Does your washer
Connecting the
water and drain
vibrate?
Adjusting the
NO
Calibration Mode
leveling feet
Running
Powering your
washing machine
Finishing the
installation
YES
Check again before steps.
Step-by-step installation
STEP 1 Selecting a location
NOTE
Before you install the washer, make sure the location:
Has a hard, level surface without carpeting or ooring that may obstruct ventilation.
Is away from direct sunlight.
Has adequate ventilation.
Is not exposed to freezing temperatures (temperatures under 32 °F or 0 °C).
Is away from heat sources such as oil or gas.
Has enough space so that the washer doesn’t rest on its power cord.
20 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 20 2016-12-13  1:21:26
STEP 2 Connecting the water supply hose
CAUTION
Before installing the water supply hoses, make sure there are rubber gaskets (B) inside the couplings (A) at both ends of each new water hose. Installing the water supply hoses without rubber gaskets can cause water leakage.
Installation
B
When you initially install the washer, be sure to use new hoses. Failing to do so may result in a water leakage or overow and
CAUTION
A
may damage your property.
CAUTION
Do not connect multiple water supply hoses together to increase the length of the supply hose. Hoses connected this way can leak and the leakage can cause electrical shock. If a hose is too short, replace the hose with a longer, high pressure hose.
English 21
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 21 2016-12-13  1:21:26
Installation
BA
Installation
1. Connect the ends of the water supply hoses to the hot and cold faucets.
2. Tighten the ttings by hand until they are snug, and then tighten them an additional two-thirds of a turn with a plier.
CAUTION
When you fasten the ttings, do not fasten them too tightly or apply tape or sealant to the faucets or water supply intakes. This can damage the ttings.
NOTE
After you have connected the water supply hoses to the faucets, ensure that they are connected correctly by pulling the water supply hoses downwards.
22 English
3. Place the unconnected ends of the hoses into a bucket and open the faucets connected to the two water supply hoses for 10 or 15 seconds to remove any foreign substances from the hoses. Close the faucets before continuing.
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 22 2016-12-13  1:21:26
4. Connect the ends of the water supply hoses to the water supply intake connections at the back of the washer.
CAUTION
The water supply hose connected to the hot faucet must be connected to the hot water supply intake and the water hose connected to the cold faucet must be connected to the cold water supply intake.
5. Tighten the ttings by hand until they are snug, and then tighten them an additional two-thirds of a turn with a plier.
NOTE
To ensure the correct water usage, connect both the hot and cold water faucets. If either or both are not connected, an “4C” (no ll) code can be displayed.
Installation
NOTE
If you do not want to use the hot water supply hose, insert the water intake cap into the hot water supply intake hole. In this case, you must select the Tap Cold for the water temperature. If you select the Tap Cold, all the lamps for the water temperature options are turned off.
CAUTION
Conrm that the water supply hoses are not twisted or bent. If the hoses are twisted or bent, the hoses can leak and cause electric shock due to the water leakage.
6. Turn on the hot and cold water supplies and check all the water supply intake connections and the faucets for water leaks.
English 23
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 23 2016-12-13  1:21:27
Installation
A
C
Installation
STEP 3 Connecting the drain hose
The end of the drain hose can be positioned in three ways:
In a Wall standpipe or Floor standpipe
The height of end of standpipe must be no lower than 39 in (99 cm) and no higher than 96 in (245 cm). If drain pipe are built into the wall with water valves (A), fasten the drain hose to the water hose.
NOTE
Make sure that the connection between the drain hose and the standpipe is not airtight.
In a laundry tub
The height of the tub must be no lower than 39 in (99 cm) and no higher than 96 in (245 cm). Assemble the supplied Hose guide at the end of the drain hose, and put the hanger on laundry tub. And fasten the drain hose to the leg of laundry tub.
24 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 24 2016-12-13  1:21:27
*
A
NOTE
Connect the hose guide (A) within 3~5 in (7.6~12.7 cm)* from the end of the drain hose. If the drain hose is extended beyond the end of the hose guide, mold or microorganisms could spread inside the washer.
NOTE
The drain hose can be installed to a 96 in (245 cm) maximum, but the draining capability can be reduced at this height. It can cause the washer to have an odor because of remaining water in the drain system.
NOTE
If the drain hose is installed below 39 in (99 cm), water can be drained in cycles due to a siphon phenomenon. It causes the washer to display “4C”.
Installation
STEP 4 Leveling your washer
A
See if the washer is level by checking the position of the tub:
1. Slide the washer into position.
2. Open the lid of the washer, and pour
the water into the tub to just below the pulsator level.
NOTE
WA52M7750A* models have the Built-in sink over the pulsator level. That’s why the level is not revealed. Open the Built-in sink and check the level with eyes.
English 25
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 25 2016-12-13  1:21:28
Installation
B C
Installation
3. If the washer is level, the pulsator (A) is positioned at the center of the water as shown in the gure. If not, level your washer by turning the front leveling feet clockwise or counterclockwise as necessary.
NOTE
Turn the front leveling feet clockwise (B) to lower the washer, and counterclockwise (C) to raise the washer.
STEP 5 Powering your washer
Plug the power cord into a 3-prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded electrical outlet.
Test run
Make sure that you install your washer correctly by running the Rinse+Spin after the installation is complete.
26 English
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 26 2016-12-13  1:21:28
STEP 6 Running a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1. Load about 6 pounds of laundry into the tub.
2. Press Power to turn on your washer.
3. Select Rinse+Spin by turning the Cycle Selector.
4. Press Start/Pause to start the test cycle.
5. The washer should not rock or vibrate excessively when water is supplied or when
washing or spinning, and should drain well during the spin cycle.
NOTE
If water leaks while water is being supplied or drained, check the water connections. Refer to the “STEP 2 Connecting the water supply hose” section on page 21 for instructions.
NOTE
If the washer rocks and vibrates excessively, level your washer again. Refer to the “STEP 4 Leveling your washer” section on page 25 for instructions.
STEP 7 Calibration Mode
Your Samsung washer detects the laundry weight automatically. For more accurate weight detection, please run Calibration Mode after the installation. To run Calibration Mode, follow these steps:
1. Remove laundry or any contents in the machine.
2. Press and hold Temp. and Delay End simultaneously for at least 3 seconds when the
power is turned on.
3. Press Start/Pause to activate Calibration Mode.
4. The pulsator rotates clockwise and counterclockwise approximately 1 minute.
5. When Calibration Mode is nished, “End” appears on the display, and the washer
automatically turns off. The washer is now ready for use.
Installation
English 27
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 27 2016-12-13  1:21:28
Operating instructions
Operating instructions
WARNING
To reduce the risk of re, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:
Loading your washer
Fill the tub with dry, unfolded clothes evenly around in order to enhance washing efciency and prevent excess wear, or wrinkling of the load.
For optimal washing performance, make sure the laundry is piled up evenly.
Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle with similar lightweight items.
When washing big bulky items or a few smaller items that don’t ll the tub completely – a rug, a pillow, stuffed toys, or one or two sweaters, for example – add a few towels to improve spin performance.
Do not insert bulky items except for Bedding in this cycle.
28 English
NOTE
During the spin cycle, the washer may add additional water to redistribute the clothes and correct an imbalance inside the drum.
When washing heavily soiled loads, do not overload your washer to ensure good cleaning results.
CAUTION
Inatable items may cause damage to the laundry or the machine during the wash or drying process.
Regardless of the size, blankets or quilts are safer and cleaner to wash one item at a time. Two different-sized blankets in the same load may compromise the drying performance due to unbalanced loads.
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 28 2016-12-13  1:21:28
To input a blanket
Fold the blanket into the blanket-specic net as shown, and then insert in the tub below the plastic area of the tub.
CAUTION
Make sure the laundry is inserted completely.
Any exposed part of the laundry may cause damage to the machine or the laundry itself, or a water leak.
Do not overload the tub. Make sure no part of the laundry is exposed outside of the tub.
To add a forgotten item:
1. Press Start/Pause to pause the washer.
2. Wait for the door to unlock automatically, and then open the door.
3. Add the item, close the door, and then press Start/Pause. The cycle will resume.
Getting started
1. Load your washer.
2. Add liquid (or powder) detergent and additives to the dispenser (see the "Detergent use"
section on page 42).
3. Select the appropriate cycle and options for the load (see the "Washing a load of laundry" section page 30).
4. Close the lid.
5. Press Start/Pause.
6. The Wash Indicator illuminates.
7. The estimated cycle time will appear in the display.
The time may uctuate to indicate the time remaining in the cycle.
Operating instructions
NOTE
The actual time required for a cycle may differ from the estimated time in the display depending on the water pressure, water temperature, detergent, and laundry.
8. Before your washer starts to ll, it will make a series of clicking noises to check the door lock and do a quick drain.
NOTE
When the cycle is complete, the Door Lock indicator will go out and “End” will appear in the display.
Pressing Power cancels the cycle and stops your washer.
The Wash, Rinse, and Spin indicators will illuminate during those portions of the cycle.
English 29
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 29 2016-12-13  1:21:29
Washing a load of laundry
WA52M7750A*
WA52M7755A*
01
02
06
07
08
09
03 04 05
13
12
11
10
14
15
01
02
06
07
08
09
03 04 05
13
12
11
10
14
15
WARNING
To reduce the risk of re, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
Control panel
WA7700M_DC68-03774D-00_EN+CFR+MES.indb 30 2016-12-13  1:21:29
Washing a load of laundry
30 English
01 Cycle Selector
02 Display
Turn the Cycle Selector to select the desired cycle. The indicator by the cycle name lights up.
Provides instructions and diagnostics while keeping you updated on the cycle status and time remaining.
Loading...
+ 125 hidden pages