Page 1
WASHING MACHINE
User’s Manual
FEATURES 1
SAFETY INSTRUCTIONS 2
DESCRIPTION OF PARTS 3
CONTROL PANEL 4
WASHING PROCEDURE 5
Fuzzy course 5
Heavy course 5
Speedy course 5
Blanket course 5
Wool course 6
Shirt course 6
Memory course 6
Clean tub course 6
Delay start 6
MANUAL FUNCTIONS 7
INSTALLATION & MAINTENANCE 8
Environment 8
Levelling 8
Connecting the water supply hose 9
Assembling the part protection panel 10
Please read this manual before using and note
how to use in the proper manner.
Please be careful of keeping the manual.
Otherwise, it should be bought separately.
In case of pump-drained washer 10
Connecting the drain hose 10
How to add the fabric softener 10
How to put the detergent in 10
Water supply connector filter 11
Cleaning the filter net 11
How to clean the filter 11
TROUBLESHOOTING 12
SPECIFICATIONS
The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.
Page 2
FEA TURES
DFC SYSTEM
• Abbreviation of Digital Freewater Control system.
As an Ideal combination of Digital temperature
control function / Digital spin control function /
Speed control function, It controls the water temperature/way of rotation / speed properly according to the clothes. This system cleans the heavy
dirt completely and delicately without damaging
the clothes.
DIGITAL TEMPERATURE CONTROL FUNCTION
• Washing detergent has it’s own temperature for
the maximum activation. The water temperature
for this activation is slightly different according to
the detergents, but normally it shows the best
effect in 30˚C ~ 45˚C. Digital temperature control
function the water in the optimum temperature
mixing the hot water and cold water properly with
the censor in the washer tub.
• In each course, the optimum water temperature is
automatically set up, but you can adjust the water
temperature manually.
DIGITAL SPIN CONTROL FUNCTION
• Realizing multi rotary manners proper to the
laundry, control the rotation of washing board
/ tub and make the washing minutely without
damaging the laundry. It makes swift current by
spinning the washing board and tub each in an
opposite direction in heavy dirt course. In light dirt
course, increase the energy efficiency spinning
the washing board only. In case of highclass
clothes, spinning the washing board / tub in one
direction together and making the smooth current
like hand washing, It reduces the damage on the
clothes.
• No need to adjust the manner of spin separately
as it automatically sets up the optimum manner
of spin in each course.
POWER INVERTER MOTOR WITH LOW-NOISE
• Washing in silence by adapting inverter resin
motor.
POWERFUL AND CLEAN STAINLESS WASHING
BOARD
• Less tangled and damaged laundry through the
magic stream of water from the powerful clean
washing board even in case of the long-term use.
MAGIC FILTER OF DOUBLE POWER
(REMAINDERS FILTER)
• Two magic filters completely block the remainders
from the laundry regardless with the water level
and this is the feature that makes the dirt off with
out additional rinsing.
POWERFUL LIQUID SOAP DEVICE
• Automatically convert powder detergent to liquid
soap promptly before it flows into the laundry and
avoid covering the laundry. Therefore, it makes
sanitary laundry.
WATER WASTE PREVENTED WASHING
MACHINE
• Reducing the unnecessary water between the
inner & outside bodies, cut down the water
consumption.
DIGITAL SPEED CONTROL FUNCTION
• Adjusting the suitable speed of spin in the
washing board / tub for each washing course and
amount of laundry with the digital spin control
function ,It makes proper force of current.
Therefore it reduces the damage on the laundry
and makes the maximum effect of washing.
• It controls the speed automatically for every
course. So, it does not need to adjust the speed
separately.
1
Page 3
SAFETY INSTRUCTIONS
Please note that the following precautions for safety intend to prevent unpredictable danger and damage
by helping the proper use in safety.
When using hot water in washing, please make sure that the water should not exceed 50˚C.
• Plastic parts may be deformed or damaged, and an electric shock or a fire may take place.
WARNING
There might be serious injury or fatal accident when
you violate this instruction.
If the power supply cord or plug is damaged or
loosened, do not use.
• An electric shock or a fire may take place.
Do not pull the cord off or touch it with moist hands.
• An electric shock or a fire may take place.
Do not bend the power supply cord by force or
press it with heavy things.
• An electric shock or a fire may take place.
Do not install the washer nearby electric implement
or don’t put a candle light or cigarette light on the
washer.
• A fire may take place.
Do not disassemble, repair or remodel it recklessly.
• When you need to repair it, please call service
agent. An electric shock or a fire may take place.
During operation, do not put your hands or metal
materials under the washer.
• You may be hurt by spinning board beneath
the washer.
Stay away from the washer when the bottom of the
washer sinks into the water.
• There might be an electric shock. Please
wait until the water drains out completely.
Do not put laundry stained with gasoline, benzene,
or alcohol in the washer, and keep the materials
away from the washer.
• An explosion or a fire may take place.
During spinning, don’t put your hand in the
spinning tub.
• It may hurt your hands. If it does not stop within
15 seconds after you open the lid, call
service agent immediately.
CAUTIONS
There might be a slight injury or damage when you
violate this instruction.
Don’t’ install it in the area with moisture or outdoor
where it has rain or snow
• An electric shock or a fire may take place.
Please unplug the power supply cord when you do
not use it.
• An electric shock or a fire may take place.
If there is dust or water on the power supply plug
and its connected part, please remove it completely.
• An electric shock or a fire may take place.
Do not make your kids look into the inside of the
washer.
• If your kid falls into the washer, his life could be
in danger.
Ventilate immediately without touching the power
plug if gas is leaking.
• An electric shock or a fire may take place if it
catches flame.
If the washer makes strange noise, smell or smoke,
unplug it promptly and call service agent.
• An electric shock or a fire may take place.
When cleaning, don’t spray water to the parts of the
washer directly.
• It may make it’s life span shorten.
Also an electric shock or fire may take place
Don’t use several appliances together with an
outlet.
• A fire may take place due to unusual heat.
Don’t press the button with an awl or pin.
• An electric shock or a fire may take place.
2
Page 4
FILTER
Lint will be collected in
the filter during
washing.
FABRIC SOFTENER
DISPENSER
LID
Be sure to keep the lid
closed during washing
and spinning.
WATER SUPPLY HOSE(HOT)
WATER SUPPLY HOSE (COLD)
DRAIN-HOSE (PUMP)
DETERGENT BOX
SPIN BASKET
Make use of the User’s Manual depending upon your washing machine model.
DESCRIPTION OF PARTS
The User’s Manual is for common use.
3
POWER CORD
BLEACH INLET
PULSATOR
GROUND LEAD
FRONT CONTROL
PANEL
When the water pipe is
metal, make sure to cover
the end of the ground wire.
WATER DRAIN HOSE
ADJUSTABLE LEGS
Adjust the length
of the legs when
installing the washer.
SOUND ABSORPTION
PANEL
Page 5
For more details, see control panel of your washing machine.
CONTROL PANEL
POWER BUTTON
•
Select it when you put the power to “ ON ” or “ OFF ”.
•
Automatically turned off after washing.
•
Automatically turned off without pressing any other
button for 10 minutes in power-off condition.
START/ HOLD BUTTON
•
Press it when you start or want to pause
DELAY START BUTTON
•
Use this function when you finish the washing on the
time you want.
•
Press power to “ OFF ” in order to cancel the
reservation.
WASH BUTTON
•
Use this function when you want to wash separately
or adjusting the washing time.(5 minutes ~ 20 minutes)
•
Keep pressing this button when choosing soak washing.
RINSE BUTTON
•
Select this function when you want to rinse only and
change the rinsing frequency.
•
You can choose maximum 5 times.
POWER
WASH
RINSE
DELAY
START
RINSE
WATER TEMP BUTTON
•
Indicates the water temperature automatically,
but control it manually as occasion demands.
•
WASHING : Choose the temperature necessary
in washing.
•
RINSING : Choose the temperature necessary in
rinsing.
•
Alterable in the middle of working
✻
Adjusting the water temperature automatically, you
should open the taps of hot water and cold water for
optimum washing.
✻
In case of not opening the tap of hot water or the
hot water not being supplied, can not control the water
temperature and do washing with cold water only.
✻
In case of wool course, cold water only is selected.
❖ WATER TEMP INDICATOR
•
When washing / rinsing each course, indicates the
adequate water temperature automatically.
•
The temperature is indicated in 4 grades.
Hot water : Supply hot water only.
Cold water : Supply cold water only.
(There might be a difference in the water temperature
according to water pressure and temperature of hot water)
: Effective for heavy dirt and control in
: Effective for activating the detergent and
control in 25~ 35˚C.
WASH
35˚C~45˚C
.
SPIN BUTTON
•
Select this button when you want to spin only and
adjust the spinning time (1minute ~ 7 minutes)
•
If you want to protect wrinkles in spinning, select this
button for 1 minute spinning.
•
If you select “Spin” only, there is a gap shown between
the timer for spinning and the timer for whole working,
which included more time for draining and holding.
LEVEL METER
•
Set it for the water drop to come in the center, moving
the adjustable legs.
SUPER RINSE BUTTON
•
Use this function when you want clean rinsing with
more of water than washing.
•
Available to rinse in one step more than the water level
of washing
SPIN
SUPER
RINSE
WATER LEVEL BUTTON
•
Water level is automatically indicated,
but you can adjust it.
•
Alterable in the middle of working.
❖ WATER LEVEL DETERGENT INDICATOR
•
In proportion to the amount of laundry, the water level
and amount of detergent are automatically indicated.
•
Indicates water level in 10 grades.
❖ MOVEMENT INDICATOR
•
Indicates the state of moving inside of clean tub.
•
Shows the water supply and the spinning direction
of washing board and tub.Indicates the selected washing
course and shows error in trouble.
❖ TIME LEFT/ DELAY START/ ERROR SIGN INDICATOR
•
Indicates the left time until the end of the washing.
•
Indicates advance time
•
Indicates the trouble in the machine and take an action
for the error with them.
❖ PROCEDURE INDICATOR
•
Indicates the procedure of washing, the remaining time
and remaining frequency.
•
In it’s procedure, it flickers.
•
If you select the washing time more than 20 minute,
soak washing is indicated .
WATER
LEVEL
4
Page 6
WASHING PROCEDURE
Before starting washing, check the following;
Connect the water supply hose to the water tap. Leave a tap
open. Plug the power cord in. Make sure to lay down the
drain hose. (In case no drain pump)
FUZZY COURSE
POWER
START/
HOLD
1. Put the laundry into the washer and push the POWER
button to on.
•
Fuzzy course button lights on.
2. Press START / HOLD button.
•
Measuring the weight of laundry, washer moves it’s body
without water and then indicates adequate amount of
water and detergent.
•
The adequate temperature of water is automatically
selected.
3. Open the lid and put the detergent/ softener in proportion
to the water level indicated. Then close the lid.
- When you open the lid in operation, it stops washing
(But water supply will be continued).
- In case of using the hot water only, cold water is supplied
during the first 20 seconds to avoid damaging the laundry
by hot water.
- On it’s operation in every course, washing time, rinsing
frequency & spinning time can be adjusted.
- With the press of the function button on water
temperature, the water temperature in washing/ rinsing
is selected manually in every course (except wool course).
- With the press of the super rinse button, additional
water is supplied in rinsing the laundry.
(except CLEAN TUB course)
HEAVY COURSE
(For Jeans or laundry
with heavy dirt)
POWER
HEAVY
START/
HOLD
1. Put the laundry in the washer and press the POWER
button to on.
2. Select HEAVY course button.
3. Press START/HOLD button.
Put the detergent/softener in proportion to the water level
and then close the lid.
Put the laundry into the washer and add detergent, too.
Be careful not to overload. Use right detergent
for the fabrics you are washing.
SPEEDY COURSE
( For laundries with light
POWER
SPEEDY
START/
HOLD
dirt like towels in a short time)
1. Put the laundry in the washer and press the
POWER button to on.
2. Select SPEEDY course button.
3. Press START/HOLD button.
Put the detergent/softener in proportion to the
water level and then close the lid.
•
Spinning the washer board brings high energy
efficiency.
•
In case of heavy laundry, it automatically spin the
washer tub to improve the power of washing.
Note
- Measuring the weight of laundry, washer moves its body
without water in every courses, and then indicates
adequate water level and amount of detergent.
(except clean tub course)
- Every course automatically indicates the water temperature
and also it can be selected by pressing the water
temperature button as you want. (except wool course)
BLANKET COURSE
(For big laundry like quilts
POWER
BLANKET
START/
HOLD
or bedcovers)
1. Put the laundry in the washer and press the POWER
button to on.
2. Select BLANKET course button.
3. Press START/HOLD button.
Put the detergent/softener in proportion to the water level
and then close the lid.
•
Blanket may get stained with the detergent.
Therefore, detergent in the liquid detergent device
is suggested.
•
Here adjusted soaking course during 20 minutes to
remove the heavy dirt at the collar of laundry (When
need more soaking, press wash button select 40
minute soaking time manually.
•
The washing board and tub spinning in the opposition
way gives great efficiency washing.
5
Page 7
WOOL COURSE
(For laundries with wool washing
POWER
WOOL
START/
HOLD
mark like sweaters, cardigans or
delicate clothes)
1. Put the laundry in the washer and press
the POWER button to on.
•
Be sure the weight of laundry is less than 2kg.
2. Select WOOL course button.
•
Select the adequate water level manually in case of light
laundry for the size
3. Press START/HOLD button.
Put the detergent/softener in proportion to the water level
and then close the lid.
•
Slightly dry the laundry at the last to avoid
wrinkles.
•
Cold water only be selected.
•
Use neutral detergent
•
Spinning into a side together or spinning the
washer board only prevent the damage on
the laundry.
SHIRT COURSE
(For shirts with dirt on the collar
POWER
SHIRT
START/
HOLD
or cuff)
1. Put the laundry in the washer and press the POWER
button to on.
2. Select SHIRT course button.
3. Press START/HOLD button.
Put the detergent/softener in proportion to the water level
and then close the lid.
•
Adjusted 20 minutes soaking to remove the heavy
dirt on the collar.
•
The washing board and tub spinning in the opposition
way, gives great efficiency washing
MEMORY COURSE
(Memorize the functions frequently
used, and you can use it easily when
washing the next time)
POWER
MEMORY
START/
HOLD
1. Put the laundry in the washer and press the
POWER button to on.
•
Check to put the functions you need before washing.
•
Refer to the following instruction on how to set up the
memory course.
2. Press MEMORY course button.
•
Selected functions are displayed on the control panel.
3. Press START/ HOLD button.
Put the detergent/softener in proportion to the water level
and then close the lid.
❖
How to set up memory course
1) Press the POWER button to on.
2) Press MEMORY button to on.
It is shown same as the beginning of Fuzzy course.
3) Select the functions frequently used manually
(such as water temperature, time of washing/spinning and
rinsing.)
4) Press the momory button one-second or more to input
selected mode (Press the button until buzzer makes
sound once more).
•
Press the START/HOLD button to run input mode.
•
Repeat the above proceduce to change the Memory
mode.
•
Even when power system turns OFF, your final input
mode is memorized.
CLEAN TUB COURSE
(in cleaning the washing tub)
POWER
CLEAN
TUB
START/
HOLD
1. Press the POWER button.
2. Press the CLEAN TUB button.
3. Press START/HOLD button.
Put the detergent in proportion to water level and
close the lid.
•
Soak washing adjusted.
•
Water temperature select button only adjustable.
•
Ideal detergent : powder bleach
•
Remove the dirt in the outer wall of the
washing tub with powerful stream of current.
DELAY START
POWER
START
HOLD
START/
DELAY
1. Put the laundry in the washer
and press the POWER button to on.
•
Make sure to open the tab.
2. Press DELAY START course button.
1) Increase one hour more each press from 3 hours and
you can select by maximum 19 hours.
2) After selected time is over, it finishes washing.
•
You can choose a course separately as you want.
3. Press START/ HOLD button.
Put the detergent in proportion to water level and close
the lid.
•
Be sure of putting the detergent into the liquid soap
device.
•
In case of putting the detergent into the laundry directly,
it may be discolored according as the reservation is
longer.
•
Press the power button in order to cancel the
reservation.
•
It could be finished at slightly different time due to the
water pressure.
6
Page 8
MANUAL FUNCTIONS
Each washing course changes manually.
Ex) If you want to wash in the speedy course : Power - Select speedy course - Wash - Start/Hold button
WASH ONLY
POWER WASH
1. Press the POWER button to on.
2. Select WAS H.
•
Press the wash button and adjust the washing time.
•
START/
HOLD
You can adjust the washing time from 5 to
20 minutes per one minute.
•
Soak washing is available.
3.Press START/HOLD button (close the lid)
Note
•
It water still remains after wash
select SPIN only.
Remainder of water to be removed.
•
Even though the water level is auto
matically set up, select the adequate
water level according to the laundry.
RINSE ONLY
POWER RINSE
SPIN ONLY
POWER SPIN
WASH + RINSE
WASH
POWER
RINSE
RINSE + SPIN
RINSE
POWER
SPIN
1. Press the POWER button to on.
2. Select RINSE.
•
Press the rinse button and select the rinsing
frequency.
START/
•
HOLD
You can adjust the frequency from 1 to 5 times.
3.Press START/HOLD button (close the lid)
1. Press the POWER button to on.
2. Select SPIN.
•
START/
HOLD
Press the spin button and adjust the time of
spinning.
•
You can adjust from 1 minute to 7 minutes.
•
The washer spins slowly in order to prevent
the clothes being tangled.
3.Press START/HOLD button (close the lid)
1. Press the POWER button to on.
2. Select WAS H and RINSE.
•
START/
HOLD
Please adjust the washing time and rinsing
frequency.
3. Press START/HOLD button.
1. Press the POWER button to on.
2. Select RINSE and SPIN.
•
START/
HOLD
Adjust the rinsing frequency and spinning time.
3. Press Start/Hold button (close the lid)
Note
•
It water still remains after wash
select SPIN only.
Remainder of water to be removed.
•
Even though the water level is
automatically set up, select the
adequate water level in case that the
laundry is soaked.
Note
•
If you select SPIN only, there is a gap
shown between the timer for spinning
and the timer for whole working, which
included more time for draining and
holding. So, note it does not mean out
of order.
Note
•
It water still remains after wash
select SPIN only.
Remainder of water to be removed.
Note
•
If more rinsing is necessary,
select the rinsing water supplement.
7
Page 9
INSTALLATION & MAINTENANCE
LOCK
UNLOCK
LOCK
UNLOCK
LOCK
UNLOCK
The User’s Manual is for common use.
Make use of the User’s Manual depending upon your washing machine model.
ENVIRONMENT
Leave some space
Maintain at least 10cm between the washer and the wall.
Place the washer on a sturdy flat surface.
If the washer is placed on an uneven or weak surface,
noise or vibration occurs. (Allowable is 1˚)
Adjust the legs for even placement.
Never install the washer near water.
Do not place the washer in steamy rooms or where the
washer is directly exposed to rain.Moisture may destroy the
electrical insulation causing an electrical shock hazard.
Avoid direct sunlight or heaters.
As plastic and electrical components are affected by direct
heat,never place the washer near furnaces, boilers, etc.
Do not place under direct sunlight.
LEVELLING
•
If the washer is not leveled with the ground, it makes the machine tremble more or be out of order.
So, make sure that the washer is leveled properly.
•
Adjust the height control legs to make eve.
Lock
Lock Nut
Adjustable
Leg
Unlock
•
After slightly lifting up the machine, rotate the
adjustable leg counter-clockwise and pull
as much as need to adjust the reight.
•
After putting down the machine after adjustment.
Lock
•
Adjust the height and secure.
•
Secure the lock nut by rotating it firmly.
•
If the lock nut is not secured, the adjustable
Unlock
leg may be released.
Waterdrop mark
Cause
The front part is
lower
Adjustment of height
If not leveled, adjust the legs to level the washer.
•
Be careful not to put in your hand under the legs.
(It may cause some injury)
How to level
Level it by adjustable legs.
Pull the handles located at the
right and left of the front side
and slide off.
Adjust the water drop mark to
be in the red circle pulling back
the machine slightly, and then,
push it with a feet to fix.
Fix the handles by hand
completely.
The back part is
lower
The left part is
lower
The right part is
lower
Adjust the height by using the adjustable rubber
or prop at the back.
Adjust the left part by using the adjustable legs
at the front and the adjustable rubber at the back.
Adjust the right part of the washer by using the adjustable leg
at the front and the adjustable rubber at the back.
8
Page 10
a
b
a
b
c
LEVELLING
(TypeB)
SEE IF THE MACHINE IS PLACED LEVEL BY CHECKING
THE POSITION OF THE WASHING TUB.
•
Open the lid of the machine, pour water into the tub up to the level
just below the pulsator, and adjust the legs so that the pulsator is
positioned at the center of the water as shown in the figure.
•
Place the machine more than
10cm away from the wall.
•
Adjust the legs on feet
for levelling .
LockLoosen
CONNECTING THE WATER SUPPLY HOSE
1.Remove the adaptor
from the water
supply hose.
1. Adjust the side horizontally
first and the front
in same direction ❷next.
2. If the thread is not
within the limit, adjust
the height of
the legs.
5. Connect the other end of the water
supply hose to the inlet water valve
at the back of the washer.
Screw the hose clockwise all the
way in.
2.First,using a "+" type
screw driver, loosen the
four screws on the adaptor.
Next,take the adaptor and
turn part(b) following the
arrow for gap about 5mm
between them.
3. Connect adaptor to the
water tap by tightening
the screws firmly.
Then, turn part (b)
following the arrow and
put (a) and (b)together.
4.Connect the water supply
hose to the adaptor. Pull down
the part (c) of the water supply
hose .When the part (c)is released,
the hose is automatically
connected to the adaptor
making a 'click' sound.
5-1.Connect the other end of the water
supply hose to the inlet water valve
at the top of the washer.
Screw the hose clockwise all the way in.
If the water tap is a screw type,assemble
a water supply hose that fits to the
tap as shown.
NOTICE After completing connection, if water leaks from the hose,
then repeat the same steps.
Use the most conventional type of faucet for water supply.
In case the faucet is square or too big,remove the spacing
ring before inserting the faucet into the adaptor.
9
Page 11
Rear-side
ASSEMBLING THE RAT PROTECTION PANEL
Tilt the washer a little and lift up the panel until it clicks,
finally fix the panel with screw to the base as shown
in the figure.
IN CASE OF PUMP-DRAINED WASHER
Take out the cap-hose and
connect the outlet-hose.
Be sure to join tightly the drain hose into
the drain-outlet on the back of the
machine.
1.Insert the sound
absorbing panel
to the assembling
hole on front side
to the end.
2.If you have difficulty
inserting the panel
lift up the washer a
little and insert it
Be sure to join tightly the drain
hose into the drain-outlet
on the side of the machine.
Anti-rat cover
Install the drain hose in the
position of about 90~100cm
above the ground.
cap-hose
outlet-hose
CONNECTING THE DRAIN HOSE
(a)
After pressing the joint ring(a), insert the drain hose(b)
to drain direction.
(b)
HOW TO ADD THE FABRIC SOFTENER
•
When a proper amount (one time does) of fabric
softener is stored in the softener inlet,it is
automatically put in at the last rinsing cycle.
•
Do not use detergent, bleach or starch into
the Softener Inlet.
•
Using too much softener may produce
unsatisfactory results.
•
Do not open the lid during the Spin Dry cycle.
If added too early, its effectiveness will decrease.
•
Do not leave the softener
into the Softener
Dispenser for a long time.
Because softner became stiff.
HOW TO PUT THE DETERGENT IN
1.Open the detergent box by pulling in the direction of the arrow as shown in the
figure and then put the powder detergent in the detergent box.
2. Put in one-time amount of detergent evenly so the detergent may not brim over the box.
Detergent Device
Put the detergent
in proportion to
water level
90~100cm
Softener Device
CAUTION : If softener is stored over the above base line, it may flow down at any time.
Softener
baseline
10
Page 12
WATER SUPPLY CONNECTOR FILTER
1.
Pull out the filter and wash well.
inlet water
valve
2.
Pull in the filter and connect
the hose to the inlet water
valve tightly.
3.
Check if there is a leakage.
Note to tighten up the
connector.
CLEANING THE FILTER NET
1. Push the upper part
of the filter and pull in.
1. Push up and
pull out the filter net.
Clean the filter net often to keep the washer clean.
2. Open the cover as
shown in the figure.
2.
Remove the collected
lint from the filter net.
HOW TO CLEAN THE FILTER
1. Place a rag under the washer filter not to wet the floor.
2. Rotate the filter counterclockwise
and pull out the filter.
3. Remove dirts and rotate
the filter clockwise
until it locks in position.
3. Clean the filter. 4. Close the cover and insert the
3. Clean the filter. 4.
(pump drained washer)
1.Place a rag under washer filter not to wet the floor.
2.Turn the filter-cap to the left.
3.Take the filter out and
remove dirts.
4. Reassemble in
reverse order.
lower part of the filter in the
basket first and then push the
filter with "click" sound .
Pull down the filter net.
11
Page 13
TROUBLESHOOTING
WASHING MACHINE WON'T WORK
Is the water tap opened?
Is the washer plugged in?
Is the power cut off?
Is there enough water?
WATER IS NOT SUPPLIED
Is the water tap opened?
Is the water cut off?
Is the water supply hose
or hose connection clogged?
Is the water tap frozen?
If water is not supplied in 1 hour,a
buzzer will sound, and the remaining
time indicator will show "WATER ERR".
WATER ERR
WATER DOSE NOT DRAIN
Is the drain hose down?(No pump)
Is the drain hose frozen?
Is the drain hose clogged?
If the water dose not drain in 15
minutes, a buzzer will sound,
and the remaining time indicator
will show "DRAIN ERR".
DRAIN ERR
CHECK YOUR VOLTAGE
If the voltage power supply
is either too high or too low,
it appears with a buzzer.
Check voltage.
Call to service center
or agency.
SPINNING DOES NOT WORK
Is the laundry spread out
evenly in the washer?
Is the washer set on a sturdy flat
surface?
"UNBALANCE"
"DOOR OPEN"
UNBALANCE
DOOR OPEN
12
Page 14
IN CASE THE NEED FOR SERVICING ARISES.
If any problem occurs with your products,do not hestitate to call any nearby.
Name, address, telephone number is required.
SPECIFICATIONS
NORMAL
CAPACITY
DIMENSIONS(mm)
WEIGHT
WATER PRESSURE
WASHING TYPE
MOTOR
INPUT
MOTOR MAX
INPUT
WASH
SPIN
WASHING
SPINNING
WASHING
SPINNING
14 kg
14 kg
W630xD700xH1020
49 kg
0.05~0.78 MPa
(0.5 ~ 8.0 kg. f/cm2)
Stirring Type
480W
180W
480W
STANDARD
WATER LEVEL
WATER USAGE
PULSATOR
ROTATING SPEED
SPINNING TUB
ROTATING SPEED
NORMAL
CAPACITY
WASHING
SPINNING
HIGH
MED
M/LOW
LOW
E/LOW
CODE NO. : DC68-01091B
90 l
80 l
70 l
57 l
42 l
210
105 rpm
700 rpm
Continue
15 Minutes
l
Loading...