Samsung VC-8615E User Manual

VC8600-RU 6/23/01 11:00 AM Page 1

VC8600-RU 6/23/01 11:00 AM Page 2

VC8600-RU 6/23/01 11:00 AM Page 3

VC8600-RU 6/23/01 11:00 AM Page 4

VC8600-RU 6/23/01 11:00 AM Page 5

VC8600-RU 6/23/01 11:00 AM Page 6

VC8600-RU 6/23/01 11:00 AM Page 7

DJ68-00086C REV(0.1)

VC8600-RU 6/23/01 11:00 AM Page 8

Operating
Instructions

❈ Before operating this unit, please read the instructions carefully.

VACUUM CLEANER

VC8615-EN 6/23/01 10:57 AM Page 3

1

Features include automatic cord rewind, dust indicator, cyclone, and sterilization lamp.
NOTE: Not all models have the same features.

1. Read all instructions carefully. Before switching on, make sure that the voltage of your electricity sup­ply is the same as that indicated on the rating plate on the bottom of the cleaner.

2. WARNING: Do not use the vacuum cleaner when rug or floor is wet.

3. Close supervision is necessary when any appliance is used by or near children. Do not allow the vac­uum cleaner to be used as a toy. Do not allow the vacuum cleaner to run unattended at any time. Use
the vacuum cleaner only for its intended use as described in the instructions.

4. Do not use the vacuum cleaner without a dust bag. Change the dust bag before it is full in order to
maintain best efficiency.

5. Do not use the vacuum cleaner to pick up matches, live ashes or cigarette butts. Keep the vacuum
cleaner away from stoves and other heat sources. Heat can deform and discolour the plastic parts of
the unit.

6. Avoid picking up hard, sharp object with the vacuum cleaner as they may damage the cleaner parts.
Do not stand on the hose assembly. Do not put a weight on the hose. Do not block the suction or the
exhaustion part.

7. Switch the vacuum cleaner off at the machine before unplugging from the electrical outlet. Grasp the
plug to disconnect from power outlet to avoid damage to cord, plug, prongs or socket. Always discon­nect cord from electrical outlet before changing the dust bag.

8. The use of an extension cord is not recommended.

9. If your vacuum cleaner is not operating correctly, switch off the power supply and consult an autho­rized service agent.

10. Do not attempt to replace a damaged power supply cord. Only the manufacturer or qualified service

personnel can replace power cords. Serious injury may result.

1. Do not use to suck up water.

2. Do not immerse in water for cleaning.

3. The hose should be checked regularly and must not be used if damaged.

IMPORTANT SAFEGUARDS

WARNING

FEATURES

VC8615-EN 6/23/01 10:57 AM Page 4

2

IDENTIFICATIONS OF PARTS

❋Features marked * may vary according to model.

❋ ❋ ❋ ACCESSORIES

CREVICE TOOL DUSTING BRUSH UPHOLSTERY BRUSH

SUCTION REGULATOR

REMOTE POWER CON­TROL* (ONLY BUTTON TYPE
MODEL)
(ONLY SLIDE TYPE MODEL)

PIPE FRIC­TION*

CYCLONE
FILTER*

TUBE*

FLOOR NOZZLE*

RUG/FLOOR
SELECTOR

HOSE CLAMP

DUST INDICATOR

UV STERILIZATION LAMP*

CORD REWIND
BUTTON

POWER-CON­TROL SWITCH
OR ON/OFF
SWITCH*

SUCTION HOSE*

DUST COVER

VC8615-EN 6/23/01 10:57 AM Page 5

3



1. Slide the free end of the extension wand into the nozzle
tube.

2. Slide the narrow end of one extension wand into the other
extension wand.

3. Slide the extension wand into the handle end of the hose.

4. Slide the hose clamp into the suction inlet of the unit.

* Option •Assemble the CYCLONIC FILTER with the handle

and extension wand(depending on model). •Ajusting the
telescopic tubes(depending on model).

EXTENDING : Holding narrow
side of the telescopic tube with a
hand, pull the hadle to the oppo­site side of it with another hand.

SHORTENING : Push the handle
to the narrow side of the tube,
hoding it with another hand.

*OPTION

*OPTION

1) PULLING OUT

The power cord is long enough to be drawn out for conve­nience.

2) REWINDING

When you have finished cleaning, disconnect the plug from the
electrical outlet and simply press the cord rewind button ligtly
with your toe.

NOTE: When removing the power cord from the electrical outlet,

grasp the plug, not the cord.

NOTE: For your convenience, the handle has two functions. It can

be used as a “handle” to carry the carry the unit, It is also
the cord rewind button that can be used to rewind the
power cord.

POWER CORD

ASSEMBLING THE VACUUM-CLEANER FOR USE

VC8615-EN 6/23/01 10:57 AM Page 6

4

With the cord plugged into an electrical outlet,
start or stop the
vacuum cleaner by pushing lightly downward
on the switch.
The vacuuming power can be adjusted to suit
any situation with
the electrical power control.

MI N = For Delicate fabrics, e.g.net curtains.
MAX = For hard floors and heavily soiled car

pets.

-To adjust power output just turn it right or left.
NOTE: ON/OFF switch is combined with

POWER CONTROLLER - To start or
stop the unit just lightly press it down­ward.

If the “Dust-Full” indicator changes to “RED” while you are cleaning, the dust bag requires
replacement.
❋ As for the “Electronic control type Vac.”, all LEDs illumination is same as “RED sign”.

NOTE : If the “Dust-Full” indicator continues to display “RED” even after changing the dust

bag, turn the cleaner off and check whether the hose, tube or nozzle is clogged.

DUST - FULL INDICATOR

SUCTION POWER CONTROL(REMOTE POWER CONTROL TYPE ONLY)

POWER CONTROL SWITCH

(VARIABLE CONTROL ONLY TYPE )

1)

REMOTE POWER CONTROL

(BUTTON TYPE)

The vacuuming power can be
adjusted to suit any situation press
handle control button.

ON/OFF : Start or stop the vacuum

cleaner.

LOW/HIGH : Adjust the suction power

by press the button.

MAX : Clean at maximum power by

press this button.

NOTE: UV lamp is illuminated in case of power supplied on vacuum cleaner.

2)

REMOTE POWER CONTROL(SLIDE TYPE)

The suction capacity can be regulated
steplessly by moving the side “A” to the
desired position.

SLIDE IN THE STOP POSITION

Vacuum-cleaner switches off (stand by
mode)

SLIDE TOWARDS MAX

Suction capacity increases steplessly
up to max.

VC8615-EN 6/23/01 10:57 AM Page 7

5

INLET FILTER
To protect the motor, your cleaner features a secondary filter at the front of the motor in the
dust comaprtment. Do not allow the filter to become clogged. Suction power reduction or
motor dam-age may result. After cleaning the secondary filter attach it in place.

• Crevice tool for radia­tors, crevices, coners,
between cushions.

USING THE ACCESSORIES

Located on the top rear
side the vacuum clean­er, there is a nozzle sup­port that can be used to
park the nozzle during
pauses in cleaning.

PARKING POSITION



OUTLET FILTER



NOTE: The filters must be completely dried before being replaced in the dust compartment.

1) Separate the
exhaust filter.

2) Reassemble it
after cleaning or
replacing the filter
in the reverse
order.

CARE OF FILTERS

For easy storage and trans­portation, this vacuum cleaner
has a clip system built onto
the body, which will keep the
tube, hose and nozzle in a
verti-cal position.

• Dusting brush for funi­ture, shelves, books,
etc.

• Upholstery brush for
cushions and drapery.

CREVICE

DUSTING UPHOLSTERY

VC8615-EN 6/23/01 10:57 AM Page 8

6

You can use a dust bag in your cleaner for a long time thanks to the Cyclonic Filter system
and it main-tain the maximum cleaning efficiency.
The larger particle of dust filtered from Cyclonic Filter remain in Dust Barrel when suctioned
air and dust revolves in the Cyclonic Filter. So the dust bag contains only smaller ones.
When the Dust Barrel is filled with dust up to the indicating line, it needs disposing and clean­ing.
Dust Barrel can be cleaned in water.

1.Turn the Dust Barrel to the left and pull it.

2.Disconnect the Cyclonic Filter from extension wand and handle.

3.Remove thread and hair tangled around the net.

4.After cleaning the Dust Barrel and Cyclonic Filter,connect the Cyclonic Filter with extension
wand and handle(washed part should be dried in the shade throughly before assembling).

5.Push and turn the Dust Barrel to the right.
Adjust indicating marks each other carved on Dust Barrel and Cyclonic Filter.

• Open the Cover-Dust
and lift the Support­Filter.

• Change the old bag for
new one.

• Insert the Support-Filter
and close the Cover­Dust.

CYCLONIC FILTER(ONLY CYCLONIC FILTER TYPES)

After using, if the cloth filter bag is full of dust, clean the cloth filter bag and use it again.

FOR CLOTH FILTER BAG

REPLACING DUST BAG

CYCLONIC FILTER

Support

Filter

DUST BARREL

CREVICE TOOL

VC8615-EN 6/23/01 10:57 AM Page 9

7

IF YOU HAVE A PROBLEM

USAGE OF FLOOR NOZZLE

PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION

DJ68-00086C REV(0.1)

1. Motor dose not start.

2. Suction force is gradual­ly decreasing

3. Cord dose not rewind
fully.

1. No power supply.

2. Nozzle, suction hose or
tube is blocked.

3. Check that the cord is not
twisted or wound unevenly.

1. Check cable, plug and sock­et.

2. Romove the object.

3. Pull the cord out 2-3m and
push down the cord rewind
button.

FOR RUG / FLOOR SELECTOR

Before use make sure that the position of the selector is in the right position for the type of
surface to be cleaned.

Select the carpet indicator when cleaning carpets.
Select flat surface indicator ➁when cleaning the floors, tiles, etc.

FOR UNIVERSAL BRUSH

Use the floor nozzle for all cleaning surfaces.

This appliance was inspected thoroughly and was in dood operating condition when it was
shipped from the factory.
If a minor problem occurs, it can usually be solved quite easily when the cause is found.
Therefore, this check list is provided for your convenience.

NOTE: For optimum efficiency, clean floor brush with DUSTING BRUSH.

This Vacuum cleaner is approved the following
EMC Directive : 89/336/EEC, 92/31/EEC and 93/68/EEC
Low Voltage Safety Directive : 73/23/EEC and 93/68/EEC

VC8615-EN 6/23/01 10:57 AM Page 10